This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.

For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.

< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
        Filter policy: White list is not used (0x00)
        Own address type: Public (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Initiating PHYs: 0x01
        Entry 0: LE 1M
          Scan interval: 60.000 msec (0x0060)
          Scan window: 60.000 msec (0x0060)
          Min connection interval: 50.00 msec (0x0028)
          Max connection interval: 70.00 msec (0x0038)
          Connection latency: 0 (0x0000)
          Supervision timeout: 420 msec (0x002a)
          Min connection length: 0.000 msec (0x0000)
          Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
      LE Extended Create Connection (0x08|0x0043) ncmd 2
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
      LE Enhanced Connection Complete (0x0a)
        Status: Success (0x00)
        Handle: 3585
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Connection interval: 67.50 msec (0x0036)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
        LE Address: DB:7E:2E:1D:85:E8 (Static)
        Flags: 0x00000000
        Data length: 27
        Name (complete): Designer Mouse
        Appearance: Mouse (0x03c2)
        Flags: 0x05
          LE Limited Discoverable Mode
          BR/EDR Not Supported
        16-bit Service UUIDs (complete): 1 entry
          Human Interface Device (0x1812)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.

The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the controller supports the Read LE Resolv List size feature, the
maximum list size are read and now stored.

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 17.979791
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 17.980629
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 17.980786
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 17.981627
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #59 [hci0] 17.981786
> HCI Event: Command Complete (0x0e) plen 12               #60 [hci0] 17.982636
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040
Signed-off-by: NAnkit Navik <ankit.p.navik@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This function allows to send a HCI command without expecting any
controller event/response in return. This is allowed for vendor-
specific commands only.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.

This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C

Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6          #11350 [hci0] 84680.231216
        Address: 56:BC:E8:24:11:68 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4                        #11351 [hci0] 84680.246022
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7         #11352 [hci0] 84680.246417
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                        #11353 [hci0] 84680.248854
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11354 [hci0] 84680.249466
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                        #11355 [hci0] 84680.253222
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                          #11356 [hci0] 84680.458387
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
        RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11357 [hci0] 84680.458737
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                        #11358 [hci0] 84680.469982
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25          #11359 [hci0] 84680.470444
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                          #11360 [hci0] 84680.474971
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0    #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4                        #11362 [hci0] 84682.551014
      LE Create Connection Cancel (0x08|0x000e) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                          #11363 [hci0] 84682.551074
      LE Connection Complete (0x01)
        Status: Unknown Connection Identifier (0x02)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Connection interval: 0.00 msec (0x0000)
        Connection latency: 0 (0x0000)
        Supervision timeout: 0 msec (0x0000)
        Master clock accuracy: 0x00

After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7    #210 [hci0] 667.152459
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                   #211 [hci0] 667.153613
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2        #212 [hci0] 667.153704
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                   #213 [hci0] 667.154584
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                     #214 [hci0] 667.182619
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
        RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2       #215 [hci0] 667.182704
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                  #216 [hci0] 667.183599
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6    #217 [hci0] 667.183645
        Address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4                  #218 [hci0] 667.184590
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25    #219 [hci0] 667.184613
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                    #220 [hci0] 667.186558
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                    #221 [hci0] 667.485824
      LE Connection Complete (0x01)
        Status: Success (0x00)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13          {0x0002} [hci0] 667.485996
        LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
        Flags: 0x00000000
        Data length: 0
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

We don't actually need the full rculist.h header in sched.h anymore,
we will be able to include the smaller rcupdate.h header instead.

But first update code that relied on the implicit header inclusion.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Since we need to change the implementation, stop exposing internals.

Provide kref_read() to read the current reference count; typically
used for debug messages.

Kills two anti-patterns:

	atomic_read(&kref->refcount)
	kref->refcount.counter
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.

This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch enables prepending appearance value to scan response data.
It also adds support for setting appearance value through mgmt command.
If currently advertised instance has apperance flag set it is expired
immediately.
Signed-off-by: NMichał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This adds support for tracing all management commands and events via the
monitor interface.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The mgmt version information will be also needed for the control
changell tracing feature. This provides a helper to pack them.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Commit 5177a838 ("Bluetooth: Add debugfs fields for hardware and
firmware info") introduced hci_set_hw_info() and hci_set_fw_info().
These functions use kvasprintf_const() but are not marked with a
__printf attribute.  Adding such an attribute helps detecting issues
related to printf-formatting at build time.
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The led_trigger field in hci_dev should be conditional based on if
CONFIG_BT_LEDS is set or not.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some Bluetooth controllers allow for reading hardware and firmware
related vendor specific infos. If they are available, then they can be
exposed via debugfs now.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The protoypes for hci_recv_frame and hci_recv_diag are in the wrong
location in the header file. Move them close to all the other hci_dev
related exported functions.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

If link is disconnected due to Authentication Failure (PIN or Key
Missing status) userspace will be notified about this with proper error
code. Many LE profiles define "PIN or Key Missing" status as indication
of remote lost bond so this allows userspace to take action on this.

@ Device Connected: 88:63:DF:88:0E:83 (1) flags 0x0000
        02 01 1a 05 03 0a 18 0d 18 0b 09 48 65 61 72 74  ...........Heart
        20 52 61 74 65                                    Rate
> HCI Event: Command Status (0x0f) plen 4
      LE Read Remote Used Features (0x08|0x0016) ncmd 1
        Status: Success (0x00)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
      ATT: Read By Group Type Request (0x10) len 6
        Handle range: 0x0001-0xffff
        Attribute group type: Primary Service (0x2800)
> HCI Event: LE Meta Event (0x3e) plen 12
      LE Read Remote Used Features (0x04)
        Status: Success (0x00)
        Handle: 3585
        Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
          LE Encryption
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
        Handle: 3585
        Random number: 0x0000000000000000
        Encrypted diversifier: 0x0000
        Long term key: 26201cd479a0921b6f949f0b1fa8dc82
> HCI Event: Command Status (0x0f) plen 4
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Encryption Change (0x08) plen 4
        Status: PIN or Key Missing (0x06)
        Handle: 3585
        Encryption: Disabled (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 3585
        Reason: Authentication Failure (0x05)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 3585
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: 88:63:DF:88:0E:83 (1) reason 4

@ Device Connected: C4:43:8F:A3:4D:83 (0) flags 0x0000
        08 09 4e 65 78 75 73 20 35                       ..Nexus 5
> HCI Event: Command Status (0x0f) plen 4
      Authentication Requested (0x01|0x0011) ncmd 1
        Status: Success (0x00)
> HCI Event: Link Key Request (0x17) plen 6
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
        Link key: 080812e4aa97a863d11826f71f65a933
> HCI Event: Command Complete (0x0e) plen 10
      Link Key Request Reply (0x01|0x000b) ncmd 1
        Status: Success (0x00)
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
> HCI Event: Auth Complete (0x06) plen 3
        Status: PIN or Key Missing (0x06)
        Handle: 75
@ Authentication Failed: C4:43:8F:A3:4D:83 (0) status 0x05
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 75
        Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 75
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: C4:43:8F:A3:4D:83 (0) reason 4
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add support for LED triggers to the Bluetooth subsystem and add kernel
config symbol BT_LEDS for it.

For now one trigger for indicating "HCI is powered up" is supported.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch implements the mgmt Start Limited Discovery command. Most
of existing Start Discovery code is reused since the only difference
is the presence of a 'limited' flag as part of the discovery state.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To make the EIR parsing helper more general purpose, make it return
the found data and its length rather than just saying whether the data
was present or not.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.

Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.

Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The discoverable mode is intrinsically linked with the connectable
mode e.g. through sharing the same HCI command (Write Scan Enable) for
BR/EDR. It makes therefore sense to move it to hci_request.c and run
the changes through the same hdev->req_workqueue.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This way the connectable changes are synchronized against each other,
which helps avoid potential races. The connectable mode is also linked
together with LE advertising which makes is more convenient to have it
behind the same workqueue.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since Add/Remove Device perform the page scan updates independently
from the HCI command completion we've introduced a potential race when
multiple mgmt commands are queued. Doing the page scan updates through
the req_workqueue ensures that the state changes are performed in a
race-free manner.

At the same time, to make the request helper more widely usable,
extend it to also cover Inquiry Scan changes since those are behind
the same HCI command. This is also reflected in the new name of the
API as well as the work struct name.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The hci_connect_le_scan() is (as the name implies) a master/central
role API, so it makes no sense in passing a role parameter to it. At
the same time this patch also fixes the direct advertising support for
LE L2CAP sockets where we now call the more appropriate hci_le_connect()
API if slave/peripheral role is desired.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since discovery also deals with LE scanning it makes sense to move it
behind the same req_workqueue as other LE scanning changes. This also
simplifies the logic since we do many of the actions in a synchronous
manner.

Part of this refactoring is moving hci_req_stop_discovery() to
hci_request.c. At the same time the function receives support for
properly handling the STOPPING state since that's the state we'll be
in when stopping through the req_workqueue.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since discovery also deals with LE scanning it makes sense to move it
behind the same req_workqueue as other LE scanning changes. This also
simplifies the logic since we do many of the actions in a synchronous
manner.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To avoid any risks of races, place also these LE scan modification
work callbacks behind the same work queue as the other LE scan
changes.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Instead of firing off a simple async request queue all background scan
updates through req_workqueue and use hci_req_sync() there to ensure
that no two updates overlap with each other.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The hci_conn_params_clear_all() function is only called from
hci_unregister_dev() at which point it's completely futile to try to
do any LE scanning updates. Simply remove this unnecessary function
call. At the same time we can make the function static since it's only
accessed from within the same c-file.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There's only one user of this helper which can be replaces with a call
to hci_pend_le_action_lookup() and a check for params->explicit_connect.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Many of the existing LE connection lookups are forced to use
hci_conn_hash_lookup_ba() which doesn't take into account the address
type. What's worse, most of the users don't bother checking that the
returned address type matches what was wanted.

This patch adds a new helper API to look up LE connections based on
their address and address type, paving the way to have the
hci_conn_hash_lookup_ba() users converted to do more precise lookups.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The hci_conn objects don't have a dedicated lock themselves but rely
on the caller to hold the hci_dev lock for most types of access. The
hci_conn_timeout() function has so far sent certain HCI commands based
on the hci_conn state which has been possible without holding the
hci_dev lock.

The recent changes to do LE scanning before connect attempts added
even more operations to hci_conn and hci_dev from hci_conn_timeout,
thereby exposing potential race conditions with the hci_dev and
hci_conn states.

As an example of such a race, here there's a timeout but an
l2cap_sock_connect() call manages to race with the cleanup routine:

[Oct21 08:14] l2cap_chan_timeout: chan ee4b12c0 state BT_CONNECT
[  +0.000004] l2cap_chan_close: chan ee4b12c0 state BT_CONNECT
[  +0.000002] l2cap_chan_del: chan ee4b12c0, conn f3141580, err 111, state BT_CONNECT
[  +0.000002] l2cap_sock_teardown_cb: chan ee4b12c0 state BT_CONNECT
[  +0.000005] l2cap_chan_put: chan ee4b12c0 orig refcnt 4
[  +0.000010] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[  +0.000013] l2cap_chan_put: chan ee4b12c0 orig refcnt 3
[  +0.000063] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[  +0.000049] hci_conn_params_del: addr ee:0d:30:09:53:1f (type 1)
[  +0.000002] hci_chan_list_flush: hcon f53d56e0
[  +0.000001] hci_chan_del: hci0 hcon f53d56e0 chan f4e7ccc0
[  +0.004528] l2cap_sock_create: sock e708fc00
[  +0.000023] l2cap_chan_create: chan ee4b1770
[  +0.000001] l2cap_chan_hold: chan ee4b1770 orig refcnt 1
[  +0.000002] l2cap_sock_init: sk ee4b3390
[  +0.000029] l2cap_sock_bind: sk ee4b3390
[  +0.000010] l2cap_sock_setsockopt: sk ee4b3390
[  +0.000037] l2cap_sock_connect: sk ee4b3390
[  +0.000002] l2cap_chan_connect: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f (type 2) psm 0x00
[  +0.000002] hci_get_route: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f
[  +0.000001] hci_dev_hold: hci0 orig refcnt 8
[  +0.000003] hci_conn_hold: hcon f53d56e0 orig refcnt 0

Above the l2cap_chan_connect() shouldn't have been able to reach the
hci_conn f53d56e0 anymore but since hci_conn_timeout didn't do proper
locking that's not the case. The end result is a reference to hci_conn
that's not in the conn_hash list, resulting in list corruption when
trying to remove it later:

[Oct21 08:15] l2cap_chan_timeout: chan ee4b1770 state BT_CONNECT
[  +0.000004] l2cap_chan_close: chan ee4b1770 state BT_CONNECT
[  +0.000003] l2cap_chan_del: chan ee4b1770, conn f3141580, err 111, state BT_CONNECT
[  +0.000001] l2cap_sock_teardown_cb: chan ee4b1770 state BT_CONNECT
[  +0.000005] l2cap_chan_put: chan ee4b1770 orig refcnt 4
[  +0.000002] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[  +0.000015] l2cap_chan_put: chan ee4b1770 orig refcnt 3
[  +0.000038] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[  +0.000003] hci_chan_list_flush: hcon f53d56e0
[  +0.000002] hci_conn_hash_del: hci0 hcon f53d56e0
[  +0.000001] ------------[ cut here ]------------
[  +0.000461] WARNING: CPU: 0 PID: 1782 at lib/list_debug.c:56 __list_del_entry+0x3f/0x71()
[  +0.000839] list_del corruption, f53d56e0->prev is LIST_POISON2 (00000200)

The necessary fix is unfortunately more complicated than just adding
hci_dev_lock/unlock calls to the hci_conn_timeout() call path.
Particularly, the hci_conn_del() API, which expects the hci_dev lock to
be held, performs a cancel_delayed_work_sync(&hcon->disc_work) which
would lead to a deadlock if the hci_conn_timeout() call path tries to
acquire the same lock.

This patch solves the problem by deferring the cleanup work to a
separate work callback. To protect against the hci_dev or hci_conn
going away meanwhile temporary references are taken with the help of
hci_dev_hold() and hci_conn_get().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.3

Some drivers might have to restore certain settings after the init
procedure has been completed. This driver callback allows them to hook
into that stage. This callback is run just before the controller is
declared as powered up.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

There are LE devices on the market that start off by announcing their
public address and then once paired switch to using private address.
To be interoperable with such devices we should simply trust the fact
that we're receiving an IRK from them to indicate that they may use
private addresses in the future. Instead, simply tie the persistency
to the bonding/no-bonding information the same way as for LTKs and
CSRKs.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This adds a new debugfs entry for enabling and disabling the vendor
diagnostic mode. It is only exposed for drivers that provide the
set_diag driver callback and actually have an option for vendor
specific diagnostic information.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Introduce hci_recv_diag function for HCI drivers to allow sending vendor
specific diagnostic messages into the Bluetooth core stack. The messages
are not processed, but they are forwarded to the monitor channel and can
be retrieved by user space diagnostic tools.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Send a HCI command and wait for command complete event.
This function serializes the requests by grabbing the req_lock.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With 9380f9ea the order of unsetting
the HCI_USER_CHANNEL flag of the HCI device was reverted to ensure
the device is first closed before making it available again.

Due to hci_dev_close checking for HCI_USER_CHANNEL being set on the
device it was never really closed and was kept opened. We're now
calling hci_dev_do_close directly to make sure the device is correctly
closed and we keep the correct order to unset the flag on our device
object.
Signed-off-by: NSimon Fels <simon.fels@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>