Given the low-level interface varies from one flash-part
manufacturer to the next, the Flash-Access-Control (FAC) mailbox
command makes the specific flash type transparent to the driver
by encapsulating a basic set of accessor and update routines.
Use these new routines where applicable by querying FAC opcode
get-sector-size at init-time.

Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Recent ISPs use this data to configure FCF information.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments.  The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Codes to support new FCoE boards.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.

[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

To instatiate pre-configured vport entities defined within an
HBA's flash memory.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

There were several places in the driver which could cause byte
ordering problem as provided by Al Viro
<viro@ZenIV.linux.org.uk>.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NRavi Anand <ravi.anand@qlogic.com>
Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Now that infrastructure is present within the midlayer and there
is a clear distinction between what is expected from a device and
target reset, convert the current device-reset codes to a
target-reset, and add codes to perform a proper device-reset (LUN
reset).

In the process of adding reset support, collapse and consolidate
large sections of mailbox-command (TMF issuance) codes,
generalize the two 'wait-for-commands-to-complete' functions, and
add a generic-reset routine for use by midlayer reset functions.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The Flash Descriptor Table (FDT) present on many recent HBAs
encodes flash accessing characteristics of the flash-part used on
the HBA.  Use this information during flash manipulation (writes)
rather than using specific hard-coded values based on queried
manufacturer and device IDs.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Recent ISPs have a region within FLASH which acts as a repository
for the logging of serious hardware and software failures.
Currently, the region is large enough to support up to 255
entries.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

FCE support enables the firmware to record FC extended link
services and basic link services frames which have been
transmitted and received by the ISP.  This allows for a limited
view of the FC traffic through the ISP without using a FC
analyzer.  This can be useful in situations where a physical
connection to the FC bus is not possible.

The driver exports this information in two ways -- first, via a
debugfs node exported for all supported ISPs under:

	<debugfs_mount_point>/qla2xxx/qla2xxx_<host_no>/fce

where a read of the 'fce' file will provide a snapshot of the
firmware's FCE buffer; and finally, the FCE buffer will be
extracted during a firmware-dump scenario.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

In preparation for FCE (Fibre Channel Event) tracing support.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Firmware will export to software the maximum number of vports
supported for any given firmware version and ISP type.  Use this
information rather than the current hardcoding of limitations
within the driver.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Large code-reuse from ISP24xx, consolidate RISC memory
extraction routines during firmware-dump.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Following patch adds support for NPIV (N-Port ID Virtualization) to the
qla2xxx.

- supported within switched-fabric topologies only.
- supports up to 63 virtual ports on each physical port.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Original code incorrectly assigned it to the driver's
link-down-timeout value (a value in seconds).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The host section of ISP24xx NVRAMs contain a new bit which
allows a user to selectively disable ports of an HBA.  These
ports (hosts) will not be presented to the midlayer.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

With ISP24XX and ISP54XX parts.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

While populating command type 6 and 7 IOCBs.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Update copyright banner.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Code scrubbing.

 - Remove trailing whitespace from driver files.
 - Remove unused #defines and inlines.
 - Standardize on C comments (// -> /* */)
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add ISP24xx definitions.

Add requisite structure definitions and #define's for ISP24xx
support.  Also drop volatile modifiers from device_reg_* register
layouts as the members are never really accessed, only their
offsets within the layout are used during reads and writes.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>