We can set, get and compare-and-exchange without using atomic_t.
Change efx_mcdi_iface::state to the enum type we really wanted it to
be.
Suggested-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The Huntington MC will reject all MCDI requests after an MC reboot until it sees
one with the NOT_EPOCH flag clear.  This flag is set by default for all requests,
and then cleared on the first request after we detect that an MC reboot has
occurred.

The old MCDI_STATUS_DELAY_COUNT gave a timeout of 10ms, which was not long enough
for the driver to detect that a reboot had occurred based on the warm boot count
while calling efx_mcdi_poll_reboot() from the loop in efx_mcdi_ev_death().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Merge the per-NIC-type MTD probe selection and struct efx_mtd_ops into
struct efx_nic_type.  Move the implementations into the appropriate
source files.

Several NVRAM functions are now only called from MTD operations which
are now implemented in the same file (falcon.c or mcdi.c).  There is no
need for them to be extern, or to be defined at all if CONFIG_SFC_MTD
is not enabled, so move them into the #ifdef CONFIG_SFC_MTD sections
in those files.

Most of the SPI-related definitions are also only used in falcon.c,
so move them there.  Put the remainder of spi.h into nic.h (which
previously included it).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

There is only one user now, but we're about to add many more.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

MCDI v2 adds a second header dword with wider command and length
fields.  It also defines extra error codes.

Change the fallback error number for unknown MCDI error codes from EIO
to EPROTO.  EIO is treated as indicating the MCDI transport has failed
and we need to reset the function, which is rather drastic.

v2 error codes and lengths don't fit into completion events, so for a
v2-capable transport, always read the response header rather then
using the event fields.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Currently we only translate error codes in efx_mcdi_poll(), but we
also need to do so in efx_mcdi_ev_cpl().

The reason we didn't notice before is that the MC firmware error codes
are mostly taken from Unix/Linux and no translation is necessary on
most architectures.  Make sure we notice any future failure by
changing the sign of resprc (matching the kernel convention) and BUG
if it's ever positive at command completion.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Move the lowest layer (transport) of the current MCDI code to
per-NIC-type operations.

Introduce a new structure and efx_nic member for MCDI-specific data.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This should probably be done during MCDI initialisation for any NIC.
Change efx_mcdi_init() to return an error code.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Collect together MCDI port functions from mcdi.c, mcdi_mac.c,
mcdi_phy.c and siena.c.  Rename the 'siena' functions accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

EF10 does not include a multicast hash filter, so this function is
specific to Siena.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

These implementations should work for EF10 too.  Rename them
accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

No need to keep open-coding the assignment of high and low dwords.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We currently require that MCDI request and response lengths are
multiples of 4 bytes, because we will copy dwords in and out of shared
memory and we want to be sure we won't read or write out of bounds.
But all we really need to know is that there is sufficient padding for
that.  Also, we should ensure that buffers are dword-aligned, as on
some architectures misaligned access will result in data corruption or
a crash.

Change the buffer type to array-of-efx_dword_t and remove the
requirement that the lengths are multiples of 4.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

A few functions are using heap buffers; change them to use stack
buffers as we really don't need to resort to the heap for a 252
byte buffer in process context.

MC_CMD_MEMCPY is quite weird in that it can use inline data placed in
the request buffer after the array of records.  Thus there are two
variable-length arrays and we can't use the normal accessors for
the second.  So we have to use _MCDI_PTR() in efx_sriov_memcpy().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We need to access arrays of 16-bit words and 32-bit dwords in MCDI
buffers based on the MCDI protocol definitions.

We should also be able to read and write fields within structures,
without specifying an array index each time.  So add MCDI_FIELD()
and make MCDI_ARRAY_FIELD() use it.  Also add MCDI_SET_FIELD().

Split MCDI_ARRAY_PTR() into MCDI_ARRAY_STRUCT_PTR() and
_MCDI_ARRAY_PTR(), which are currently identical but will diverge in
later changes.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Add _MCDI_DWORD() which yields an lvalue for the given dword field
and change MCDI_DWORD(), MCDI_SET_DWORD() and MCDI_QWORD() to use it.

Fold the rather trivial MCDI_PTR2() into MCDI_PTR() and _MCDI_DWORD().

Remove MCDI_SET_DWORD2() and MCDI_QWORD2().  MCDI_DWORD2() should also
go, but it still has one user which we'll get rid of later.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

MCDI_DECLARE_BUF declares a variable as an MCDI buffer of the
requested length, adding any necessary padding.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The least significant bit number (LBN) of a field within an MCDI
structure is counted from the start of the structure, not the
containing dword.  In MCDI_ARRAY_FIELD() we need to mask it rather
than using the usual EFX_DWORD_FIELD() macro.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

For NIC/System time synchonisation efx_mcdi_rpc needs to be split in
efx_mcdi_rpc_start and efx_mcdi_rpc_finish operations.
Signed-off-by: NStuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register.  These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.

We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.

There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF.  Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.

The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.

This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The SFC9000-family controllers have firmware to manage all board
peripherals including temperature, heat sink continuity and voltage
sensors.  The firmware reports sensor alarms, which we log, and
will shut down the board if necessary.

Some users may want to monitor their boards more closely, so add an
hwmon driver that exposes all sensors reported by the firmware.  Move
efx_mcdi_sensor_event() into the new file so it can share the array of
sensor labels with the hwmon driver.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

No NICs need to switch efx_mac_operations at run-time, and the MAC
operations are fairly closely bound to NIC types.

Move efx_mac_operations::reconfigure to efx_nic_type::reconfigure_mac
and efx_mac_operations::check_fault fo efx_nic_type::check_mac_fault.
Change callers to call through efx->type or directly if the NIC type
is known.

Remove efx_mac_operations::update_stats.  The implementations for
Falcon used to fetch MAC statistics synchronously and this was used by
efx_register_netdev() to clear statistics after running self-tests.
However, it now only converts statistics that have already been
fetched (and that only for Falcon), and the call from
efx_register_netdev() has no effect.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.

CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We currently make no use of siena_nic_data::fw_{version,build} except
to format the firmware version for ethtool_get_drvinfo().  Since we
only read the version at start of day, this information is incorrect
after an MC firmware update.  Remove the cached version information
and read it via MCDI whenever it is requested.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Make local functions and variable static. Do some rearrangement
of the string table stuff to put it where it gets used.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this.  Also, their buffers are
declared as variable-length arrays with no explicit maximum length.

Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the SFC9000 family of 10G Ethernet controllers
and LAN-on-motherboard chips, starting with the SFL9021 'Siena' and
SFC9020 'Bethpage'.

The SFC9000 family is based on the SFC4000 'Falcon' architecture, but
with some significant changes:

- Two ports are associated with two independent PCI functions
  (except SFC9010)
- Integrated 10GBASE-T PHY(s) (SFL9021/9022)
- MAC, PHY and board peripherals are managed by firmware
  - Driver does not require board-specific code
  - Firmware supports wake-on-LAN and lights-out management through NC-SI
- IPv6 checksum offload and RSS
- Filtering by MAC address and VLAN (not included in this code)
- PCI SR-IOV (not included in this code)

Credit for this code is largely due to my colleagues at Solarflare:

   Guido Barzini
   Steve Hodgson
   Kieran Mansley
   Matthew Slattery
   Neil Turton
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>