When rescanning for logical drives, store information about whather
raid offload is enabled for each logical drive, and update the driver's
internal record of this.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This enables sending i/o's destined for RAID logical drives
which can be serviced by a single physical disk down a different,
faster i/o path directly to physical drives for certain logical
volumes on SSDs bypassing the Smart Array RAID stack for a
performance improvement.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NDon Brace <brace@beardog.cce.hp.com>
Signed-off-by: NJoe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For "mode 1" io accelerated commands, the command tag is in
a different location than for commands that go down the normal
RAID path, so the abort handler needs to take this into account.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When commands sent down the "fast path" fail, they must be re-tried down the
normal RAID path.  We do this by kicking i/o's back to the scsi mid layer with
a DID_SOFT_ERROR status, which causes them to be retried.  This won't work for
SG_IO's and other non REQ_TYPE_FS i/o's which could get kicked all the way back
to the application, which may have no idea that the command needs resubmitting
and likely no way to resubmit it in such a way the that driver can recognize it
as a resubmit and send it down the normal RAID path.  So we just always send
non REQ_TYPE_FS i/o's down the normal RAID path, never down the "fast path".
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For certain i/o's to certain devices (unmasked physical disks) we
can bypass the RAID stack firmware and do the i/o to the device
directly and it will be faster.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This is normally optional, but for SSD Smart Path support (in
subsequent patches) it is required.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

There is an extended report luns command which contains
additional information about physical devices.  In particular
we need to get the physical device handle so we can use an
alternate i/o path for fast physical devices like SSDs so
we can speed up certain i/o's by bypassing the RAID stack
code in the controller firmware.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

spin_lock_irqsave for the HBA lock is called in one function where flag
is local to that function. Another function is called from the first
function where lock has to be released using spin_unlock_irqrestore for
calling task_done of libsas. In the second function also flag is declared
and used. For calling task_done there is no need to enable the irq. So
instead of using spin_lock_irqsave and spin_unlock_irqrestore, spin_lock
and spin_unlock is used now. This also avoids passing the flags across all
the functions where HBA lock is being used. Also removed redundant code.
Reported-by: NJason Seba <jason.seba42@gmail.com>
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: NViswas G <viswas.g@pmcs.com>
Acked-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 254f796b updated
the driver to use 16 MSI-X vectors, despite the fact that
older controllers would provide only 4.
This was causing MSI-X registration to drop down to INTx
mode. But as the controller support performant mode, the
initialisation will become confused and cause the machine
to stall during boot.

This patch fixes up the MSI-X registration to re-issue
the pci_enable_msix() call with the correct number of
MSI-X vectors. With that the hpsa driver continues to
works on older controllers like the P200.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch fixes kernel panic issue while booting into the kdump kernel.

We have triggered crash and kdump vmcore was successful. No issues seen while
booting into the OS.
Signed-off-by: NMahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

pthru32->dataxferlen comes from the user so we need to check that it's
not too large so we don't overflow the buffer.
Reported-by: NNico Golde <nico@ngolde.de>
Reported-by: NFabian Yamaguchi <fabs@goesec.de>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch makes reject messages show right value for opcode and itt, which
is converse previously.
Signed-off-by: NVaughan Cao <vaughan.cao@oracle.com>
Acked-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fixed following smatch warnings in bfa.
drivers/scsi/bfa/bfa_ioc.c:3882 bfa_sfp_show_comp() error: memcpy()
'des' too small (64 vs 248)
drivers/scsi/bfa/bfa_ioc.c:6859 bfa_flash_status_read() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:6881 bfa_flash_status_read() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:6917 bfa_flash_read_start() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:7043 bfa_flash_raw_read() warn: unsigned
'status' is never less than zero.
Signed-off-by: NVijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add the missing unlock before return from function bfad_iocmd_cfg_trunk()
in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NVijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When the host template doesn't declare an eh_host_reset_handler
the eh_deadline mechanism is pointless and will set the
device to offline. So disable eh_deadline if no
eh_host_reset_handler is present.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In the highly unusual case where two threads are running concurrently through
the scanning code scanning the same target, we run into the situation where
one may allocate the target while the other is still using it.  In this case,
because the reap checks for STARGET_CREATED and kills the target without
reference counting, the second thread will do the wrong thing on reap.

Fix this by reference counting even creates and doing the STARGET_CREATED
check in the final put.
Tested-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # delay backport for 2 months for field testing
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch eliminates the reap_ref and replaces it with a proper kref.
On last put of this kref, the target is removed from visibility in
sysfs.  The final call to scsi_target_reap() for the device is done from
__scsi_remove_device() and only if the device was made visible.  This
ensures that the target disappears as soon as the last device is gone
rather than waiting until final release of the device (which is often
too long).
Reviewed-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # delay backport by 2 months for field testing
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This makes sure format strings cannot leak into the printk call via the
constructed buffer.
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

sparse says:
drivers/scsi/lpfc/lpfc_sli.c:16547:37: warning:
 Using plain integer as NULL pointer
Signed-off-by: NDaeseok Youn <daeseok.youn@gmail.com>
Acked-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Report from coverity
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix module parameter descriptions mentioning default values that no longer
match the code.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

qla2x00_mem_alloc() returns 1 on success and -ENOMEM on failure.  On the
one hand the caller assumes non-zero is success but on the other hand
the caller also assumes that it returns an error code.

I've fixed it to return zero on success and a negative error code on
failure.  This matches the documentation as well.

[jejb: checkpatch fix]
Fixes: e315cd28 ('[SCSI] qla2xxx: Code changes for qla data structure refactoring')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>