This patch (as1637) cleans up the way ehci-hcd handles end-of-resume
port signalling.  When the PORT_RESUME bit in the port's status and
control register is cleared, we shouldn't be setting the PORT_SUSPEND
bit at the same time.  Not doing this doesn't seem to have hurt so
far, but we might as well do the right thing.

Also, the patch replaces an estimated value for what the port status
should be following a resume with the actual register value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1635) rearranges the control-flow logic in
ehci_iaa_watchdog() slightly to agree better with the comments.  It
also changes a verbose-debug message to a regular debug message.
Expiration of the IAA watchdog is an unusual event and can lead to
problems; we need to know about it if it happens during debugging.  It
should not be necessary to set a "verbose" compilation option.

No behavioral changes other than the debug message.  Lots of apparent
changes to the source text, though, because the indentation level was
decreased.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1634) simplifies some of the code associated with the
per-port change bits added in EHCI-1.1, and in particular it fixes a
bug in the logic of ehci_hub_status_data().  Even if the change bit
doesn't indicate anything happened on a particular port, we still have
to notify the core about changes to the suspend or reset status.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1657) decreases the timeout used by ehci-hcd for polling
the async and periodic schedule statuses.  The timeout is currently
set to 20 ms, which is much too high.  Controllers should always
update the schedule status within one or two ms of being told to do
so; if they don't then something is wrong.

Furthermore, bug reports have shown that sometimes controllers
(particularly those made by VIA) don't update the status bit at all,
even when the schedule does change state.  When this happens, polling
for 20 ms would cause an unnecessarily long delay.

The delay is reduced to somewhere between 2 and 4 ms, depending on the
slop allowed by the kernel's high-res timers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As it does almost nothing, get rid of omap_ehci_init()
and move the ehci->caps initialization part into probe().

Also remove the outdated TODO list from header.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move PHY initialization until after EHCI initialization is
complete, instead of initializing the PHYs first, shutting
them down again, and then initializing them a second time.

This fixes HSIC device detection.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Even when not in PHY mode, the USB device on the port (e.g. HUB)
might need resources like RESET which can be modelled as a PHY
device. So try to get the PHY device in any case.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allows the OMAP EHCI controller to be specified via device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allows the OHCI controller found in OMAP3 and later chips to
be specified via device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since there is only one resource per type we don't really need
to use resource name to obtain it. This also also makes it easier
for device tree adaptation.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since there is only one resource per type we don't really need
to use resource name to obtain it. This also also makes it easier
for device tree adaptation.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In PHY mode we need to have the nop-usb-xceiv transceiver
driver to operate, so select it in Kconfig.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PHY regulator handling must be done in the PHY driver
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reset GPIO handling for the PHY must be done in the PHY
driver. We use the PHY helpers instead to reset the PHY.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For each port that is in PHY mode we obtain a PHY device using the USB PHY
library and put it out of suspend.

It is up to platform code to associate the PHY to the controller's
port and it is up to the PHY driver to manage the PHY's resources.

Also remove weird spacing around declarations we come across.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make use of devm_ioremap_resource() and correct comment.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1645) converts ehci-omap over to the new "ehci-hcd is a
library" approach, so that it can coexist peacefully with other EHCI
platform drivers and can make use of the private area allocated at
the end of struct ehci_hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A failed kzalloc() is reported with a dev_err that dereferences the null
sisusb, this will cause a NULL pointer deference error.

Instead, pass dev->dev to the dev_err() rather than &sisusb->sisusb_dev->dev

Smatch analysis:

drivers/usb/misc/sisusbvga/sisusb.c:3087 sisusb_probe() error: potential null
  dereference 'sisusb'.  (kzalloc returns null)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

remove cast for kmalloc return value.
Signed-off-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-usb@vger.kernel.org
Cc: usb-storage@lists.one-eyed-alien.net
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NPaul Vlase <vlase.paul@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Modern speed handling has been introduced in 2009 by commit
9b80fee1 (cdc_acm: Fix to use modern
speed interfaces) and the acm_tty_speed array has been unused since.
Signed-off-by: NSamuel Tardieu <sam@rfc1149.net>
Acked-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

kfree on NULL pointer is a no-op.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix trivial kernel-doc warnings:
Warning(include/linux/usb.h:574): No description found for parameter 'usb3_lpm_enabled'
Warning(include/linux/usb.h:574): Excess struct/union/enum/typedef member 'usb_classdev' description in 'usb_device'
Warning(include/linux/usb.h:574): Excess struct/union/enum/typedef member 'usbfs_dentry' description in 'usb_device'

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Smatch complains because we only allocate ONETOUCH_PKT_LEN (2) bytes
but later when we call usb_fill_int_urb() we assume maxp can be up
to 8 bytes.  I talked to the maintainer and maxp should be capped at
ONETOUCH_PKT_LEN.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty port ops shutdown() routine is not called for console ports;
remove extra check.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It is not very useful to indicate the the driver is about to be probed.

Quoting Alan Stern [1]:

"Plenty of drivers don't include any message like this at all.  You
might as well get rid of it entirely."

Remove such dev_info().

[1] http://marc.info/?l=linux-usb&m=136138896132433&w=2Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit c0304996 (USB: ehci-mxc: remove Efika MX-specific CHRGVBUS hack)
there is no need to include <asm/mach-types.h>, so remove it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Staticize usbmisc_imx6q_drv_init/exit() to fix the following sparse warnings:

drivers/usb/chipidea/usbmisc_imx6q.c:147:12: warning: symbol 'usbmisc_imx6q_drv_init' was not declared. Should it be static?
drivers/usb/chipidea/usbmisc_imx6q.c:153:13: warning: symbol 'usbmisc_imx6q_drv_exit' was not declared. Should it be static?
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver has been nothing but trouble, and no one shipping a new
Android device uses it, so let's just drop it, making the USB Gadget
driver authors lives a whole lot easier as they do their rework.

Cc: John Stultz <john.stultz@linaro.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull namespace bugfixes from Eric Biederman:
 "This is three simple fixes against 3.9-rc1.  I have tested each of
  these fixes and verified they work correctly.

  The userns oops in key_change_session_keyring and the BUG_ON triggered
  by proc_ns_follow_link were found by Dave Jones.

  I am including the enhancement for mount to only trigger requests of
  filesystem modules here instead of delaying this for the 3.10 merge
  window because it is both trivial and the kind of change that tends to
  bit-rot if left untouched for two months."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  proc: Use nd_jump_link in proc_ns_follow_link
  fs: Limit sys_mount to only request filesystem modules (Part 2).
  fs: Limit sys_mount to only request filesystem modules.
  userns: Stop oopsing in key_change_session_keyring

There is a more complete atmel patch-series out by Nick Dyer that fixes
this and other things, but in the meantime this is the minimal thing to
get the touchscreen going on (at least my) Pixel Chromebook.

Not that I want my dirty fingers near that beautiful screen, but it
seems that a non-initialized touchscreen will also end up being a
constant wakeup source, so you have to disable it to go to sleep.  And
it's easier to just fix the initialization sequence.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update proc_ns_follow_link to use nd_jump_link instead of just
manually updating nd.path.dentry.

This fixes the BUG_ON(nd->inode != parent->d_inode) reported by Dave
Jones and reproduced trivially with mkdir /proc/self/ns/uts/a.

Sigh it looks like the VFS change to require use of nd_jump_link
happend while proc_ns_follow_link was baking and since the common case
of proc_ns_follow_link continued to work without problems the need for
making this change was overlooked.

Cc: stable@vger.kernel.org
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Pull btrfs fixes from Chris Mason:
 "These are scattered fixes and one performance improvement.  The
  biggest functional change is in how we throttle metadata changes.  The
  new code bumps our average file creation rate up by ~13% in fs_mark,
  and lowers CPU usage.

  Stefan bisected out a regression in our allocation code that made
  balance loop on extents larger than 256MB."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: improve the delayed inode throttling
  Btrfs: fix a mismerge in btrfs_balance()
  Btrfs: enforce min_bytes parameter during extent allocation
  Btrfs: allow running defrag in parallel to administrative tasks
  Btrfs: avoid deadlock on transaction waiting list
  Btrfs: do not BUG_ON on aborted situation
  Btrfs: do not BUG_ON in prepare_to_reloc
  Btrfs: free all recorded tree blocks on error
  Btrfs: build up error handling for merge_reloc_roots
  Btrfs: check for NULL pointer in updating reloc roots
  Btrfs: fix unclosed transaction handler when the async transaction commitment fails
  Btrfs: fix wrong handle at error path of create_snapshot() when the commit fails
  Btrfs: use set_nlink if our i_nlink is 0

Add basic platform data to get the current upstream driver working
with the 224s touchpad and 1664s touchscreen.
We will be using NULL config so we will use the settings from the
devices' NVRAMs.
Signed-off-by: NBenson Leung <bleung@chromium.org>
Tested-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.

This will cause the driver to perform some touchpad specific
initializations, such as:
  * register input device name "Atmel maXTouch Touchpad" instead of
  Touchscreen.
  * register BTN_LEFT & BTN_TOOL_* event types.
  * register axis resolution (as a fixed constant, for now)
  * register BUTTONPAD property
  * process GPIO buttons using reportid T19

Input event GPIO mapping is done by the platform data key_map array.

key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Tested-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull CIFS fixes from Steve French:
 "A small set of cifs fixes which includes one for a recent regression
  in the write path (pointed out by Anton), some fixes for rename
  problems and as promised for 3.9 removing the obsolete sockopt mount
  option (and the accompanying deprecation warning)."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix missing of oplock_read value in smb30_values structure
  cifs: don't try to unlock pagecache page after releasing it
  cifs: remove the sockopt= mount option
  cifs: Check server capability before attempting silly rename
  cifs: Fix bug when checking error condition in cifs_rename_pending_delete()

Merge misc fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  alpha: boot: fix build breakage introduced by system.h disintegration
  memcg: initialize kmem-cache destroying work earlier
  Randy has moved
  ksm: fix m68k build: only NUMA needs pfn_to_nid
  dmi_scan: fix missing check for _DMI_ signature in smbios_present()
  Revert parts of "hlist: drop the node parameter from iterators"
  idr: remove WARN_ON_ONCE() on negative IDs
  mm/mempolicy.c: fix sp_node_init() argument ordering
  mm/mempolicy.c: fix wrong sp_node insertion
  ipc: don't allocate a copy larger than max
  ipc: fix potential oops when src msg > 4k w/ MSG_COPY