Add a DEBUG(MTD_DEBUG_LEVEL2, ..) trace at beginning of sst_write() function as
it is done in m25p80_write() function.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Untested, but expected to be compatible with MX25L25635E which I did
test.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This is a 256Mbit (32MiB) part so minor changes were made to support
4-byte addressing.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Commit b34bc037 removed the
"unrecognized JEDEC id" error message, causing the probe function to
silently abort if the flash ID is unrecognized.

It is desirable to produce diagnostic output in this situation so that
the user has some idea what went wrong.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

While building an x86 distro kernel, I hit the following:

Kernel: arch/x86/boot/bzImage is ready  (#7)
ERROR: "of_mtd_parse_partitions" [drivers/mtd/devices/m25p80.ko]
undefined!

of_mtd_parse_partitions is defined with MTD_OF_PARTS, and that's only
built on PPC and microblaze.  The code in question should be wrapped w/
a stricter #ifdef.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds support for the Winbond W25Q64 serial flash.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds support for Spansion S25FL016K and S25FL064K SPI flash.
It has been tested with physical devices. Note that both parts exhibit
a Winbond manufacturer ID so they might also be added to that section.
Signed-off-by: NGernot Hoyler <Gernot.Hoyler@spansion.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
[grant.likely@secretlab.ca: wrap hunk with #ifdef CONFIG_OF]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

"plat_id" is always non-NULL here.  There is a zero element on the end
of the m25p_ids[] array and if we hit the end of the loop then plat_id
points to that.

This would lead to a NULL pointer dereference later on in the function.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This is just a cleanup, it doesn't fix any bugs.

These functions all check retlen inconsistently and it generates a
warning in Smatch (http://smatch.sf.net).  If retlen were ever NULL it
would cause an oops and the code has been this way since 2006 so someone
would have complained.  Also I looked at other places that implemented
the mtd read and write functions and they dereference retlen without
checking.

I removed the checks.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

spi_write_then_read() may return its own return codes (e.g. -EIO),
so let's propagate the value down to the probe().

Also, remove jedec == 0 check, it isn't needed as nowadays we use
dedicated SPI device IDs for non-JEDEC flashes.
Suggested-by: NBarry Song <21cnbao@gmail.com>
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Since commit 18c6182b ("Rework
probing/JEDEC code"), m25p80 driver successfully registers chips
even if JEDEC probing fails.

This was needed to support non-JEDEC flashes. Though, it appears
that some platforms (e.g. blackfin bf533 stamp[1]) used the old
behavior to detect if there's any flash connected, so the driver
have to fail on JEDEC probing errors.

This patch restores the old behavior for JEDEC flashes, and adds
"-nonjedec" SPI device IDs for M25Pxx flashes, so that the kernel
still supports non-JEDEC flashes.

[1] http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=5975

Reported-by: Mingquan Pan
Reported-by: NBarry Song <21cnbao@gmail.com>
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add support for Macronix 25L8005.  Tested on a HP t5325 Thin Client.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

CAT25 chips (as manufactured by On Semiconductor, previously Catalyst
Semiconductor) are similar to the original M25Px0 chips, except:

- Address width can vary (1-2 bytes, in contrast to 3 bytes in M25P
  chips). So, implement convenient m25p_addr2cmd() and m25p_cmdsz()
  calls, and place address width information into flash_info struct;

- Page size can vary, therefore we shouldn't hardcode it, so get rid
  of FLASH_PAGESIZE definition, and place the page size information
  into flash_info struct;

- CAT25 EEPROMs don't need to be erased, so add NO_ERASE flag, and
  propagate it to the mtd subsystem.

[dwmw2: Fix up for conflicts with DMA safety patch]
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Previosly the driver always tried JEDEC probing, assuming that non-JEDEC
chips will return '0'. But truly non-JEDEC chips (like CAT25) won't do
that, their behaviour on RDID command is undefined, so the driver should
not call jedec_probe() for these chips.

Also, be less strict on error conditions, don't fail to probe if JEDEC
found a chip that is different from what platform code told, instead
just print some warnings and use an information obtained via JEDEC. In
that case we should not trust partitions any longer, but they might be
still useful (i.e. they could protect some parts of the chip).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch converts the m25p80 driver so that now it uses .id_table
for device matching, making it properly detect devices on OpenFirmware
platforms (prior to this patch the driver misdetected non-JEDEC chips,
seeing all chips as "m25p80").

Also, now jedec_probe() only does jedec probing, nothing else. If it
is not able to detect a chip, NULL is returned and the driver fall
backs to the information specified by the platform (platform_data, or
exact ID).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

spi_write() requires the buffer to be DMA-safe, kmalloc()
it seperately to ensure this.
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

The SST SPI flashes is like Atmel SPI flashes in that the software
protection bits are set by default at power up, so clear them at init
time.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
 devices/m25p80.c
 devices/slram.c
 linux version 2.6.30
 ftl.c
 nand/cafe_nand.c
 nand/cmx270_nand.c
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Tested 64KiB block size only.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Support SST25WF{512,010,020,040} SPI flashes.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The SST SPI flashes are a bit non-standard in that they can be programmed
one byte at a time (including address!), or they can be written two bytes
at a time with auto address incrementing (AAI).  The latter form is
obviously much better for performance, so let's use it when possible.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NSiddarth Gore <gores@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch fixes the following oops, observed with MTD_PARTITIONS=n:

m25p80 spi32766.0: m25p80 (1024 Kbytes)
Unable to handle kernel paging request for data at address 0x00000008
Faulting instruction address: 0xc03a54b0
Oops: Kernel access of bad area, sig: 11 [#1]
Modules linked in:
NIP: c03a54b0 LR: c03a5494 CTR: c01e98b8
REGS: ef82bb60 TRAP: 0300   Not tainted  (2.6.31-rc4-00167-g4733fd32)
MSR: 00029000 <EE,ME,CE>  CR: 24022022  XER: 20000000
DEAR: 00000008, ESR: 00000000
TASK = ef82c000[1] 'swapper' THREAD: ef82a000
GPR00: 00000000 ef82bc10 ef82c000 0000002e 00001eb8 ffffffff c01e9824 00000036
GPR08: c054ed40 c0542a08 00001eb8 00004000 22022022 1001a1a0 3ff8fd00 00000000
GPR16: 00000000 00000001 00000000 00000000 ef82bddc c0530000 efbef500 ef8356d0
GPR24: 00000000 ef8356d0 00000000 efbf7a00 c0530ec4 ffffffed efbf5300 c0541f98
NIP [c03a54b0] m25p_probe+0x22c/0x354
LR [c03a5494] m25p_probe+0x210/0x354
Call Trace:
[ef82bc10] [c03a5494] m25p_probe+0x210/0x354 (unreliable)
[ef82bca0] [c024e37c] spi_drv_probe+0x2c/0x3c
[ef82bcb0] [c01f1afc] driver_probe_device+0xa4/0x178
[ef82bcd0] [c01f06e8] bus_for_each_drv+0x6c/0xa8
[ef82bd00] [c01f1a34] device_attach+0x84/0xa8
...
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The m25p16 data sheet from numonyx lists the worst-case bulk erase time
(tBE) as 40 seconds.
Signed-off-by: NSteven A. Falco <sfalco@harris.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

this patch add m45pe10 [1] chip support to the m25p80 driver.

[1] http://www.numonyx.com/Documents/Datasheets/M45PE10.pdfSigned-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Extend erase timeout in M25P80 SPI Flash driver.

The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.
Signed-off-by: NPeter Horton <zero@colonel-panic.org>
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There is a logic error in "whole chip erase" for the m25p80 family.  If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase.  This patch corrects that.

Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc.  Increasing it allows me to successfully program
the device on my board.
Signed-off-by: NSteven A. Falco <sfalco@harris.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Follow-on patch to the previous driver model patch for the MTD
framework.  This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.

Based on a patch from Kay Sievers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a
DaVinci-specific driver to the <linux/mtd/partitions.h> header.

Use those to eliminate #ifdefs in two drivers which had their own
definitions of mtd_has_partitions().

Quite a lot of other MTD drivers could benefit from using use one or both
of these to remove #ifdeffery.  Maybe some Janitors would like to help.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

CC: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>