Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since submit 621b4d66 the bnx2x driver support FW GRO.
However, when using the device with GRO enabled in bridging
scenarios throughput is very low, as the bridge expects all
incoming packets to be passed with CHECKSUM_PARTIAL -
a demand which is satisfied by the SW GRO implementation,
but was missed in the bnx2x driver implementation (which returned
CHECKSUM_UNNECESSARY).

Now, given that the traffic is supported by FW GRO (TCP/IP),
the bnx2x driver calculates the pseudo checksum by itself,
passing skbs with CHECKSUM_PARTIAL and giving a much better
throughput when receiving GRO traffic.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enabling interrupts, acknowledge the interrupt only
after configuring the IGU to the correct interrupt mode
(otherwise it would dirty selftests)
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get better control over interrupts during panic, and allow FW to
test outgoing Tx packets when stop-on-error is allowed.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This revises and enhances the bnx2x register dump facilities,
adding support for `ethtool -w' on top of `ethtool -d'.
Signed-off-by: NMiriam Shitrit <miris@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On rare occasions, self test link may fail since the link is
being sampled while it's still being stabilized.
To correct this behaviour, try to sample the link for 2 seconds
prior to declaring a failure.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current logic causes chips running in switch dependent multi-function
FCoE mode not to configure their MAC, leading to an all 0s MAC.

This patch configures the interface with the SAN Mac instead.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Self-tests following boot from SAN have failed as the
UNDI driver might leave some NIG interrupt indications.

This patch does the clean-up, clearing those indications
and allowing the test to pass.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit a5e371f6 ("drivers/net: delete
all code/drivers depending on CONFIG_MCA") most of the MCA drivers went,
including the Kconfig/Makefile hooks for ibmlana, but it seems that I
missed the "git rm" on these actual driver files, and with the namespace
overlap with machine check architecture, it got missed by various git
grep type checking done at that time.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects some problems with LSM/SELinux that were introduced
with the multiqueue patchset.  The problem stems from the fact that the
multiqueue work changed the relationship between the tun device and its
associated socket; before the socket persisted for the life of the
device, however after the multiqueue changes the socket only persisted
for the life of the userspace connection (fd open).  For non-persistent
devices this is not an issue, but for persistent devices this can cause
the tun device to lose its SELinux label.

We correct this problem by adding an opaque LSM security blob to the
tun device struct which allows us to have the LSM security state, e.g.
SELinux labeling information, persist for the lifetime of the tun
device.  In the process we tweak the LSM hooks to work with this new
approach to TUN device/socket labeling and introduce a new LSM hook,
security_tun_dev_attach_queue(), to approve requests to attach to a
TUN queue via TUNSETQUEUE.

The SELinux code has been adjusted to match the new LSM hooks, the
other LSMs do not make use of the LSM TUN controls.  This patch makes
use of the recently added "tun_socket:attach_queue" permission to
restrict access to the TUNSETQUEUE operation.  On older SELinux
policies which do not define the "tun_socket:attach_queue" permission
the access control decision for TUNSETQUEUE will be handled according
to the SELinux policy's unknown permission setting.
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Acked-by: NEric Paris <eparis@parisplace.org>
Tested-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ifb should lookup devices in the appropriate namespace.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: NKosta Zertsekel <konszert@marvell.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only user is cxgb3 driver.

old_neigh is used to check device change, but it must not happen
on redirect.  In this sense, we can remove old_neigh argument.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The removal of the 8390 EISA drivers actually comprises the
complete content of the EISA probe block, so we can now remove
that block, and its hook into the unified probe.  Note that
the deleted comment mentions PCI probes, but they long since
moved elsewhere, so no PCI probes are touched here.

We get rid of the orphaned EISA probe prototypes, and a couple
of left over MCA probe prototypes at the same time.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit e49cc34f introduced an unconditional IRQ_HANDLED return in be_intx()
to workaround Lancer and BE2 HW issues. This is bad as it prevents the kernel
from detecting interrupt storms due to broken HW.

The BE2/Lancer HW issues are:
1) In Lancer, there is no means for the driver to detect if the interrupt
belonged to device, other than counting and notifying events.
2) In Lancer de-asserting INTx takes a while, causing the INTx irq handler
to be called multiple times till the de-assert happens.
3) In BE2, we see an occasional interrupt even when EQs are unarmed.

Issue (1) can cause the notified events to be orphaned, if NAPI was already
running.
This patch fixes this issue by scheduling NAPI only if it is not scheduled
already. Doing this also takes care of possible events_get() race that may be
caused due to issue (2) and (3). Also, IRQ_HANDLED is returned only the first
time zero events are detected.
(Thanks Ben H. for the feedback and suggestions.)
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reference count leaking of both module and sock were found:

- When a detached file were closed, its sock refcnt from device were not
  released, solving this by add the sock_put().
- The module were hold or drop unconditionally in TUNSETPERSIST, which means we
  if we set the persist flag for N times, we need unset it for another N
  times. Solving this by only hold or drop an reference when there's a flag
  change and also drop the reference count when the persist device is deleted.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael points out that even after Stefan's fix the TUNSETIFF is still allowed
to create a new tap device. This because we only check tfile->tun but the
tfile->detached were introduced. Fix this by failing early in tun_set_iff() if
the file is detached. After this fix, there's no need to do the check again in
tun_set_iff(), so this patch removes it.

Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to use rtnl_dereference() instead of the open code, suggested by Eric.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

in/out_be32 accessors are Power arch centric whereas
ioread/writebe32 are available in other arches.  Also, unlike
in/out_be32, ioread/writebe32 expect non-volatile address arguments.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is werid that qlge driver supports NETIF_F_TSO6 but
not NETIF_F_IPV6_CSUM. This also causes some kernel warning [1]
when VLAN device setups on a qlge interface.

I think the qlge hardware doesn't support NETIF_F_IPV6_CSUM,
so we have to just remove the NETIF_F_TSO6 flag.

After this patch, the TCP/IPv6 traffic becomes normal again,
no kernel warnings any more.

NOTE: I only tested it on 2.6.32 kernel, even if the upstream
kernel could fix this automatically (it is hard to track NETIF*
flags), removing it is also safe.

1. https://bugzilla.redhat.com/show_bug.cgi?id=891839

Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a missing break statement so FLASH_5762_EEPROM_HD gets treated
like FLASH_5762_EEPROM_LD.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver is used on Microblaze and will be used
on Arm Zynq.
Microblaze doesn't define NO_IRQ and no IRQ is 0.
Arm still uses NO_IRQ as -1 and there is no option
to connect IRQ to irq 0.

That's why <= 0 is only one option how to find out
undefined IRQ.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Axi ethernet can't be used on PPC because it is
little endian IP and PPC is big endian.
This system can't be designed.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of the previous driver unload flow, whenever bnx2x is
loaded after the UNDI driver it closes all Rx traffic.
However, this leads to management traffic also being stopped until
the network interface associated with one of its functions gets loaded.

To remedy this, management traffic is re-opened once the 'cleaning'
after the previous driver ends.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating Tx queues, if for some reason
(e.g., lack of memory) allocation fails, driver will incorrectly
calculate the pointers of the various queues.

This patch repositions all pointers in such a case to point at
sequential structures in memory, allowing the bnx2x macros to
be used correctly when accessing them.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 70ac618c ("ptp: fixup Kconfig for two PHC drivers.") removed all
dependencies for the blackfin hardware time-stamping Kconfig entry. Hardware
time-stamping is only available on BF518 though. Since the Kconfig entry is
'default y', just updateing your kernel source and running `make defconfig` will
result in the the following build errors:

	drivers/net/ethernet/adi/bfin_mac.c:694: error: implicit declaration of function ‘bfin_read_EMAC_PTP_CTL’
	drivers/net/ethernet/adi/bfin_mac.c:702: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FV3’
	drivers/net/ethernet/adi/bfin_mac.c:712: error: implicit declaration of function ‘bfin_write_EMAC_PTP_CTL’
	drivers/net/ethernet/adi/bfin_mac.c:717: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FOFF’
	...

This patch adds back the dependency on BF518, and since it does not make sense
to expose this config option when the blackfin MAC driver is not enabled also
restore the dependency on BFIN_MAC.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the moment, we check owner when we enable queue in tun.
This seems redundant and will break some valid uses
where fd is passed around: I think TUNSETOWNER is there
to prevent others from attaching to a persistent device not
owned by them. Here the fd is already attached,
enabling/disabling queue is more like read/write.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I move the return down a line after the debugging printk.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multiqueue tun devices support detaching a tun_file from its tun_struct
and re-attaching at a later point in time.  This allows users to disable
a specific queue temporarily.

ioctl(TUNSETIFF) allows the user to specify the network interface to
attach by name.  This means the user can attempt to attach to interface
"B" after detaching from interface "A".

The driver is not designed to support this so check we are re-attaching
to the right tun_struct.  Failure to do so may lead to oops.
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Static checkers complained that the E1H_FUNC_MAX define is used
incorrectly in bnx2x_pretend_func(). The complaint was justified,
although its not a real bug, as the first part of the conditional
protects us in this case (a real bug would happen if a VF tried to
use the pretend func, but there are no VFs in E1H chips).
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit d0e2c55e (veth: avoid a NULL deref in veth_stats_one)
we now clear the peer pointers in veth_dellink()

veth_close() must therefore make sure the peer pointer is set.
Reported-by: NTom Parkin <tom.parkin@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With Hard-Wired firmware configuration it was incorrectly provisioning the VFs
Channel Access Rights Mask.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix DSA whitespace issues reported by checkpatch.pl
Signed-off-by: NBarry Grussling <barry@grussling.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert DSA printk calls to netdev_info calls as recommended by
checkpatch.pl.
Signed-off-by: NBarry Grussling <barry@grussling.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert DSA msleep calls to timeout/usleep_range calls
as reported by checkpatch.pl.
Signed-off-by: NBarry Grussling <barry@grussling.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert DSA driver comments to network-style comments as reported by
checkpatch.pl.  Fix spelling error.
Signed-off-by: NBarry Grussling <barry@grussling.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>