xHCI 1.0 hosts have a set of requirements on how to align transfer
buffers on the endpoint rings called "TD fragment" rules.  When the
ax88179_178a driver added support for scatter gather in 3.12, with
commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a:
enable tso if usb host supports sg dma", it broke the device under xHCI
1.0 hosts.  Under certain network loads, the device would see an
unexpected short packet from the host, which would cause the device to
stop sending ethernet packets, even through USB packets would still be
sent.

Commit 35773dac "usb: xhci: Link TRB must not occur within a USB
payload burst" attempted to fix this.  It was a quick hack to partially
implement the TD fragment rules.  However, it caused regressions in the
usb-storage layer and userspace USB drivers using libusb.  The patches
to attempt to fix this are too far reaching into the USB core, and we
really need to implement the TD fragment rules correctly in the xHCI
driver, instead of continuing to wallpaper over the issues.

Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0
hosts.  Only the ax88179_178a driver checks the no_sg_constraint flag,
so don't set it for 1.0 hosts.  This should not impact usb-storage or
usbfs behavior, since they pass down max packet sized aligned sg-list
entries (512 for USB 2.0 and 1024 for USB 3.0).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMark Lord <mlord@pobox.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org # 3.12

Commit afe2dab4 ("USB: add hex/bcd detection to usb modalias generation")
changed the routine that generates alias ranges. Before that change, only
digits 0-9 were supported; the commit tried to fix the case when the range
includes higher values than 0x9.

Unfortunately, the commit didn't fix the case when the range includes both
0x9 and 0xA, meaning that the final range must look like [x-9A-y] where
x <= 0x9 and y >= 0xA -- instead the [x-9A-x] range was produced.

Modprobe doesn't complain as it sees no difference between no-match and
bad-pattern results of fnmatch().

Fixing this simple bug to fix the aliases.
Also changing the hardcoded beginning of the range to uppercase as all the
other letters are also uppercase in the device version numbers.

Fortunately, this affects only the dvb-usb-dib0700 module, AFAIK.
Signed-off-by: NJan Moskyto Matejka <mq@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix a memory leak in the usb_store_new_id() error paths. When bailing out
due to sanity checks, the function left the already allocated usb_dynid
struct in place. This regression was introduced by the following commits:

c63fe8f6 (usb: core: add sanity checks when using bInterfaceClass with new_id)
1b9fb31f (usb: core: check for valid id_table when using the RefId feature)
52a6966c (usb: core: bail out if user gives an unknown RefId when using new_id)

Detected by Coverity: CID 1162604.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding two more IDs to the ftdi_sio usb serial driver.
It now connects Tagsys RFID readers.
There might be more IDs out there for other Tagsys models.
Signed-off-by: NUlrich Hahn <uhahn@eanco.de>
Cc: Johan Hovold <johan@hovold.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This device was mentioned in an OpenWRT forum.  Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
 0: qcdm
 2: nmea
 3: modem
 8: qmi
 9: storage

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

People sometimes create their own custom-configured kernels and forget
to enable CONFIG_SCSI_MULTI_LUN.  This causes problems when they plug
in a USB storage device (such as a card reader) with more than one
LUN.

Fortunately, we can tell fairly easily when a storage device claims to
have more than one LUN.  When that happens, this patch asks the SCSI
layer to probe all the LUNs automatically, regardless of the config
setting.

The patch also updates the Kconfig help text for usb-storage,
explaining that CONFIG_SCSI_MULTI_LUN may be necessary.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NThomas Raschbacher <lordvan@lordvan.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for ANT USB-m Stick from Dynastream Innovations, by listing
USB pid

[34366.944805] usb 6-1: New USB device found, idVendor=0fcf, idProduct=1009
[34366.944817] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[34366.944824] usb 6-1: Product: ANT USB-m Stick
[34366.944831] usb 6-1: Manufacturer: Dynastream Innovations

Device reported (https://code.google.com/p/antpm/issues/detail?id=5) to
work through:
$ modprobe usbserial vendor=0x0fcf product=0x1009
Signed-off-by: NKristóf Ralovich <kristof.ralovich@gmail.com>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds an unusual-devs entry for the BlackBerry 9000.  This
fixes Bugzilla #22442.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NMoritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Tested-by: NMoritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Cypress ATACB unusual-devs entry for the Super Top SATA bridge
causes problems.  Although it was originally reported only for
bcdDevice = 0x160, its range was much larger.  This resulted in a bug
report for bcdDevice 0x220, so the range was capped at 0x219.  Now
Milan reports errors with bcdDevice 0x150.

Therefore this patch restricts the range to just 0x160.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NMilan Svoboda <milan.svoboda@centrum.cz>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

the PHY layer is supposed to be optional,
considering some PHY have no control bus
for SW to poke around.

After commit 1ae5799e (usb: hcd: Initialize
USB phy if needed) any HCD which didn't provide
a PHY driver would emit annoying error messages.

In this patch we're decreasing those messages
to debugging only and we also add a PHY prefix
or use dev_dbg so we know where they're coming from.
Reported-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.

The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.

Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: NAndre Heider <a.heider@gmail.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit beb7e592 "staging: dwc2: add check on dwc2_core_reset
return" broke the B -> A role switching on OTG-enabled platforms.
This commit fixes it.
Reported-by: NDinh Nguyen <dinguyen@altera.com>
Tested-by: NDinh Nguyen <dinguyen@altera.com>
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add usb_disabled() check to prevent kernel oops when booting with "nousb"
in the cmdline:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at bus_add_device+0xe0/0x18c
LR is at device_add_groups+0x1c/0x20
...
[<c02191c0>] (bus_add_device) from [<c0217130>] (device_add+0x41c/0x538)
[<c0217130>] (device_add) from [<c023b1d4>] (usb_new_device+0x270/0x35c)
[<c023b1d4>] (usb_new_device) from [<c0241174>] (usb_add_hcd+0x4fc/0x760)
[<c0241174>] (usb_add_hcd) from [<c0254ce0>] (dwc2_hcd_init+0x434/0x510)
[<c0254ce0>] (dwc2_hcd_init) from [<c02594f4>] (dwc2_driver_probe+0x130/0x170)
[<c02594f4>] (dwc2_driver_probe) from [<c021bbd0>] (platform_drv_probe+0x28/0x58)
Signed-off-by: NAndre Heider <a.heider@gmail.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-linus-2014-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:

xhci: Fix some regressions introduced in 3.14.

Hi Greg,

Here's four patches for 3.14.

One of them adds an xHCI host quirk, and the other three of them fix
regressions introduced in 3.14.  One regression causes USB 3.0 Link PM to
be enabled on all xHCI hosts (even those that may not support it), which
causes some USB 3.0 devices to not enumerate.  A second regression causes
some xHCI hosts that don't support 64-bit addressing to stop responding to
commands and die.

Note, these patches don't fix the recent usbfs regression that was caused
by commit 35773dac "usb: xhci: Link TRB
must not occur within a USB payload burst".  I'm waiting for those patches
to be tested.

Please pull usb-linus into usb-next, as I have feature patches that rely on
140e3026 Revert "usbcore: set lpm_capable field for LPM capable root
hubs"

Sarah Sharp

Pull parisc updates from Helge Deller:
 "The three major changes in this patchset is a implementation for
  flexible userspace memory maps, cache-flushing fixes (again), and a
  long-discussed ABI change to make EWOULDBLOCK the same value as
  EAGAIN.

  parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
  to keep HP-UX compatibility.  Since we will probably never implement
  full HP-UX support, we prefer to drop this compatibility to make it
  easier for us with Linux userspace programs which mostly never checked
  for both values.  We don't expect major fall-outs because of this
  change, and if we face some, we will simply rebuild the necessary
  applications in the debian archives"

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add flexible mmap memory layout support
  parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
  parisc: convert uapi/asm/stat.h to use native types only
  parisc: wire up sched_setattr and sched_getattr
  parisc: fix cache-flushing
  parisc/sti_console: prefer Linux fonts over built-in ROM fonts

HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps.  We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.

Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.

In the current implementation of the buffer cache, buffers are allocated
in the pagecache.  That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space.  So, we don't
need to allocate extra memory and copy the content of the buffers there.

This patch optimizes the code to avoid copying the buffers.  It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs.  This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.

New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.

This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: NHelge Deller <deller@gmx.de>

On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: NGuy Martin <gmsoft@tuxicoman.be>
Signed-off-by: NHelge Deller <deller@gmx.de>

The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: NHelge Deller <deller@gmx.de>

Signed-off-by: NHelge Deller <deller@gmx.de>

This commit:
f8dae006: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.

This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NJohn David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: NHelge Deller <deller@gmx.de>

The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available.  This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13

Pull hwmon kconfig fixes from Jean Delvare.

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors
  hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors

Pull SLAB changes from Pekka Enberg:
 "Random bug fixes that have accumulated in my inbox over the past few
  months"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  mm: Fix warning on make htmldocs caused by slab.c
  mm: slub: work around unneeded lockdep warning
  mm: sl[uo]b: fix misleading comments
  slub: Fix possible format string bug.
  slub: use lockdep_assert_held
  slub: Fix calculation of cpu slabs
  slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings

Pull turbostat updates from Len Brown.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: introduce -s to dump counters
  tools/power turbostat: remove unused command line option
  turbostat: Add option to report joules consumed per sample
  turbostat: run on HSX
  turbostat: Add a .gitignore to ignore the compiled turbostat binary
  turbostat: Clean up error handling; disambiguate error messages; use err and errx
  turbostat: Factor out common function to open file and exit on failure
  turbostat: Add a helper to parse a single int out of a file
  turbostat: Check return value of fscanf
  turbostat: Use GCC's CPUID functions to support PIC
  turbostat: Don't attempt to printf an off_t with %zx
  turbostat: Don't put unprocessed uapi headers in the include path

Pull ARM SoC fixes from Olof Johansson:
 "Here's a set of patches for (hopefully) -rc1.  Some of them are fixes,
  but a good number of them also do things such as enable new drivers in
  the defconfigs for platforms that have such devices, increases
  coverage of the multiplatform defconfig and some DTS changes that
  plumbs up some of the devices that now have bindings and driver
  support.

  The commit dates are recent; we've mostly collected these fixes in the
  last few days but I also had to rebuild the branch yesterday to sort
  out some internal conflicts which reset the timestamps.  The changes
  should have been tested by each platform maintainer already (and few
  of them have cross-platform impact) so I'm personally not too
  concerned by it at this time"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
  ARM: multi_v7_defconfig: add mvebu drivers
  clocksource: kona: Add basic use of external clock
  drivers: bus: fix CCI driver kcalloc call parameters swap
  ARM: dts: bcm28155-ap: Fix Card Detection GPIO
  ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
  ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
  MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
  ARM: dts: zynq: Add SDHCI nodes
  ARM: hisi: don't select SMP
  ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
  ARM: multi_v7: copy most options from tegra_defconfig
  ARM: iop32x: fix power off handling for the EM7210 board
  ARM: integrator: restore static map on the CP
  ARM: msm_defconfig: Enable MSM clock drivers
  ARM: dts: msm: Add clock controller nodes and hook into uart
  ARM: OMAP4+: move errata initialization to omap4_pm_init_early
  ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
  ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
  ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
  ...

Similar to what was done for the lm75 driver.

Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: NEduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

Based on an earlier attempt by Randy Dunlap.

Fix SENSORS_LM75 dependencies to eliminate build errors:

drivers/built-in.o: In function `lm75_remove':
lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `lm75_probe':
lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register'

Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: NEduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

The new option allows just run turbostat and get dump of counter values. It's
useful when we have something more than one program to test.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The -s is not used, let's remove it, and update quick help accordingly.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Pull misc kbuild changes from Michal Marek:
 "The non-critical part of kbuild is small this time:
   - Three fixes for make deb-pkg
   - A new coccinelle check

  One of the deb-pkg fixes is a leftover from the last merge window,
  hence the merge commit"

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  deb-pkg: Fix building for MIPS big-endian or ARM OABI
  deb-pkg: Fix cross-building linux-headers package
  scripts: Coccinelle script for pm_runtime_* return checks with IS_ERR_VALUE
  deb-pkg: Inhibit initramfs builders if CONFIG_BLK_DEV_INITRD is not set

Both proc files are writeable and used for configuring cells. But
there is missing correct mode flag for writeable files. Without
this patch both proc files are read only.

[ It turns out they aren't really read-only, since root can write to
  them even if the write bit isn't set due to CAP_DAC_OVERRIDE ]
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With commit d8d14bd0 ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.

However I missed that there was still a stale declaration in
arch/tile/..  which now causes a compile error on tile:

  In file included from fs/dcookies.c:28:0:
  include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
  fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'

Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged.  The correct declaration is now in include/linux/compat.h

The build error was reported by Fenguang's build bot.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "A set of cifs fixes (mostly for symlinks, and SMB2 xattrs) and
  cleanups"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Fix check for regular file in couldbe_mf_symlink()
  [CIFS] Fix SMB2 mounts so they don't try to set or get xattrs via cifs
  CIFS: Cleanup cifs open codepath
  CIFS: Remove extra indentation in cifs_sfu_type
  CIFS: Cleanup cifs_mknod
  CIFS: Cleanup CIFSSMBOpen
  cifs: Add support for follow_link on dfs shares under posix extensions
  cifs: move unix extension call to cifs_query_symlink()
  cifs: Re-order M-F Symlink code
  cifs: Add create MFSymlinks to protocol ops struct
  cifs: use protocol specific call for query_mf_symlink()
  cifs: Rename MF symlink function names
  cifs: Rename and cleanup open_query_close_cifs_symlink()
  cifs: Fix memory leak in cifs_hardlink()

Pull vfs fixes from Al Viro:
 "Several obvious fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Fix mountpoint reference leakage in linkat
  hfsplus: use xattr handlers for removexattr
  Typo in compat_sys_lseek() declaration
  fs/super.c: sync ro remount after blocking writers
  vfs: unexport the getname() symbol

Pull rtl8812ae staging wireless driver from Greg KH:
 "Here's a single staging driver for a wireless chipset that has shown
  up in the SteamBox hardware.  It is merged separately from the "main"
  staging pull request to sync up with the wireless api changes that
  came in from the networking tree.

  It's self-contained and works for me and others.  Larry will be
  replacing it with a "real" driver for 3.15, but for now this one is
  needed"

* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8821ae: Enable build by reverting BROKEN marking
  staging: r8821ae: Fix build problems
  Staging: rtl8812ae: disable due to build errors
  Staging: rtl8821ae: add TODO file
  Staging: rtl8821ae: removed unused functions and variables
  Staging: rtl8821ae: rc.c: fix up function prototypes
  Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver

Revert commit ef83b078 "PCI: Remove from bus_list and release
resources in pci_release_dev()" that made some nasty race conditions
become possible.  For example, if a Thunderbolt link is unplugged
and then replugged immediately, the pci_release_dev() resulting from
the hot-remove code path may be racing with the hot-add code path
which after that commit causes various kinds of breakage to happen
(up to and including a hard crash of the whole system).

Moreover, the problem that commit ef83b078 attempted to address
cannot happen any more after commit 8a4c5c32 "PCI: Check parent
kobject in pci_destroy_dev()", because pci_destroy_dev() will now
return immediately if it has already been executed for the given
device.

Note, however, that the invocation of msi_remove_pci_irq_vectors()
removed by commit ef83b078 from pci_free_resources() along with
the other changes made by it is not added back because of subsequent
code changes depending on that modification.

Fixes: ef83b078 (PCI: Remove from bus_list and release resources in pci_release_dev())
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>