Split up ipoib_ib_handle_wc() into ipoib_ib_handle_rx_wc() and
ipoib_ib_handle_tx_wc() to make the code easier to read.  This will
also help implement NAPI in the future.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fast Memory Registration (fmr) is used to register for rdma an sg whose
elements are not linearly sequential after dma mapping.

The IB verbs layer provides an "all dma memory MR (memory region)" which
can be used for RDMA-ing a dma linearly sequential buffer.

Change the code to use the dma mr instead of doing fmr when dma mapping
produces a single dma entry sg.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

fix and add some debug prints related to iser
handling of memory for rdma.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

As iser is able to use at most one rdma operation for the
execution of a scsi command, and registration of the sg
associated with scsi command has its restrictions, the code
checks if an sg is "aligned for rdma".

Alignment for rdma is measured in "fmr page" units whose
possible resolutions are different between HCAs and can be
smaller, equal or bigger to the system page size.

When the system page size is bigger than 4KB (eg the default
with ia64 kernels) there a bigger chance that an sg would be
aligned for rdma if the fmr page size is 4KB.

Change the code to create FMR whose pages are of size 4KB
and to take that into account when processing the sg.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Currently, the data length of a command coming down from scsi-ml
is limited only by the size of its sg list (sg_tablesize). The
max data length may be different for different page size values.
By setting max_sectors, we limit the data length to
max_sectors*512 bytes.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

dma mapping may include a "compaction" of the sg associated with scsi command.
Hence, the size of the maximal prefix of the SG which is aligned for rdma must be
compared against the length of the dma mapped sg (mem->dma_nents) and not against
the size of it before it was mapped (mem->size).
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Closes a window where address resolution can attach an rdma_cm_id to a
device during destruction of the rdma_cm_id.  This can result in the
rdma_cm_id remaining in the device list after its memory has been
freed.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a driver for the Ammasso 1100 gigabit ethernet RNIC.
Signed-off-by: NTom Tucker <tom@opengridcomputing.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Modifications to the existing rdma header files, core files, drivers,
and ulp files to support iWARP, including:
 - Hook iWARP CM into the build system and use it in rdma_cm.
 - Convert enum ib_node_type to enum rdma_node_type, which includes
   the possibility of RDMA_NODE_RNIC, and update everything for this.
Signed-off-by: NTom Tucker <tom@opengridcomputing.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add an iWARP Connection Manager (CM), which abstracts connection
management for iWARP devices (RNICs).  It is a logical instance of the
xx_cm where xx is the transport type (ib or iw).  The symbols exported
are used by the transport independent rdma_cm module, and are
available also for transport dependent ULPs.
Signed-off-by: NTom Tucker <tom@opengridcomputing.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove some trailing whitespace that has snuck in despite the best
efforts of whitespace=error-all.  Also fix a few other whitespace
bogosities.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Randomize the starting local comm ID to avoid getting a rejected
connection due to a stale connection after a system reboot or
reloading of the ib_cm.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The ib_mad module does not use a kthread function, but mad_priv.h
includes <linux/kthread.h>.  mad_rmpp.c does not do any DMA-related
stuff, but includes <linux/dma-mapping.h>.  Remove the unused includes.
Signed-off-by: NJames Lentini <jlentini@netapp.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The implementation assumes that any RMPP request that requires a
response uses DS RMPP.  Based on the RMPP start-up scenarios defined
by the spec, this should be a valid assumption.  That is, there is no
start-up scenario defined where an RMPP request is followed by a
non-RMPP response.  By having this assumption we avoid any API
changes.

In order for a node that supports DS RMPP to communicate with one that
does not, RMPP responses assume a new window size of 1 if a DS ACK has
not been received.  (By DS ACK, I'm referring to the turn-around ACK
after the final ACK of the request.)  This is a slight spec deviation,
but is necessary to allow communication with nodes that do not
generate the DS ACK.  It also handles the case when a response is sent
after the request state has been discarded.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set the reject code properly when rejecting a request that contains an
invalid GID.  A suitable GID is returned by the IB CM in the
additional reject information (ARI).  This is a spec compliancy issue.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Enable atomic operations along with RDMA reads if a local RDMA
read/atomic depth is provided by the user.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Incorrect number of bits was taken for static_rate field.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

port_num was not being returned for unconnected QPs.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When default static rate is returned for Tavor, need to translate it
to an ib rate value.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This stops the generic poll code from waiting for a timeout.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is useful for testing purposes.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Also added the word "Hardware" after "Fatal" to make it more obvious
that it's hardware, not software.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch only renames files, fixes product names, and updates
comments.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When we first submitted a userspace subnet management agent, it was
rejected, so we left it out of the final driver submission.  This patch
removes a number of vestigial references to it.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A lot of ipath layer code was only called in one place. Now that the
ipath_core and ib_ipath drivers are merged, it's more sensible to simply
inline the simple stuff that the layer code was doing.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There is little point in keeping the two drivers separate, so we are
merging them.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Some userlands try to mmap these pages read-write, so accommodate them.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Change comment: no longer imply that user can set ipath_kpiobufs to zero.
Actually set ipath_kpiobufs from parameter. Previously only altered
per-device ipath_lastport_piobuf, which was over-written in chip init.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Allocate enough pointers for all possible ports, to avoid problems in
cleanup/unload.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>