For hardware doesn't support use specified speed and duplex
to negotiate, it's unnecessary to check and modify the port
speed and duplex for fibre port when autoneg is on.

Fixes: 22f48e24 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when hns3 driver configures the tm shaper to limit
bandwidth below 20Mbit using the parameters calculated by
hclge_shaper_para_calc(), the actual bandwidth limited by tm
hardware module is not accurate enough, for example, 1.28 Mbit
when the user is configuring 1 Mbit.

This patch adjusts the ir_calc to be closer to ir, and
always calculate the ir_b parameter when user is configuring
a small bandwidth. Also, removes an unnecessary parenthesis
when calculating denominator.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After setting new channel num, it needs free old ring memory and
allocate new ring memory. If there is no enough memory and allocate
new ring memory fail, the ring may initialize fail. To make sure
the network interface can work normally, driver should revert the
channel to the old configuration.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds ethtool_ops.set_channels support for HNS3 VF driver,
and updates related TQP information and RSS information, to support
modification of VF TQP number, and uses current rss_size instead of
max_rss_size to initialize RSS.

Also, fixes a format error in hclgevf_get_rss().
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: implement firmware loading policy

Dirk says:

This series adds configuration capabilities to the firmware loading policy of
the NFP driver.

NFP firmware loading is controlled via three HWinfo keys which can be set per
device: 'abi_drv_reset', 'abi_drv_load_ifc' and 'app_fw_from_flash'.
Refer to patch #11 for more detail on how these control the firmware loading.

In order to configure the full extend of FW loading policy, a new devlink
parameter has been introduced, 'reset_dev_on_drv_probe', which controls if the
driver should reset the device when it's probed. This, in conjunction with the
existing 'fw_load_policy' (extended to include a 'disk' option) provides the
means to tweak the NFP HWinfo keys as required by users.

Patches 1 and 2 adds the devlink modifications and patches 3 through 9 adds the
support into the NFP driver. Furthermore, the last 2 patches are documentation
only.

v2:
  Renamed all 'reset_dev_on_drv_probe' defines the same as the devlink parameter
  name (Jiri)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the initial documentation for the NFP driver specific
documentation.

Right now, only basic information is provided about acquiring firmware
and configuring device firmware loading.

Original driver documentation can be found here:
https://github.com/Netronome/nfp-drv-kmods/blob/master/README.mdSigned-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed the incorrect prefix for the 'nfp_fw_load' function.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the 'reset_dev_on_drv_probe' devlink parameter. The
reset control policy is controlled by the 'abi_drv_reset' hwinfo key.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the 'fw_load_policy' devlink parameter. The FW load
policy is controlled by the 'app_fw_from_flash' hwinfo key.

Remap the values from devlink to the hwinfo key and back.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register devlink parameters for driver use. Subsequent patches will add
support for specific parameters.

In order to support devlink parameters, the management firmware needs to
be able to lookup and set hwinfo keys.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware reset and loading policies can be controlled with the
combination of three hwinfo keys, 'abi_drv_reset', 'abi_drv_load_ifc'
and 'app_fw_from_flash'.

'app_fw_from_flash' defines which firmware should take precedence,
'Disk', 'Flash' or the 'Preferred' firmware. When 'Preferred'
is selected, the management firmware makes the decision on which
firmware will be loaded by comparing versions of the flash firmware
and the host supplied firmware.

'abi_drv_reset' defines when the driver should reset the firmware when
the driver is probed, either 'Disk' if firmware was found on disk,
'Always' reset or 'Never' reset. Note that the device is always reset
on driver unload if firmware was loaded when the driver was probed.

'abi_drv_load_ifc' defines a list of PF devices allowed to load FW on
the device.

Furthermore, we limit the cases to where the driver will unload firmware
again when the driver is removed to only when firmware was loaded by the
driver and only if this particular device was the only one that could
have loaded firmware. This is needed to avoid firmware being removed
while in use on multi-host platforms.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the NSP HWinfo set command. This closely follows the
HWinfo lookup command.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are cases where we want to read a hwinfo entry from the NFP, and
if it doesn't exist, use a default value instead.

To support this, we must silence warning/error messages when the hwinfo
entry doesn't exist since this is a valid use case. The NSP command
structure provides the ability to silence command errors, in which case
the caller should log any command errors appropriately. Protocol errors
are unaffected by this.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the simple command that indicates whether application
firmware is loaded.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the 'reset_dev_on_drv_probe' devlink parameter, controlling the
device reset policy on driver probe.

This parameter is useful in conjunction with the existing
'fw_load_policy' parameter.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the 'disk' value to the generic 'fw_load_policy' devlink parameter.
This value indicates that firmware should always be loaded from disk
only.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: add PCL support

This small series implements the ethtool RXNFC operations in the
mv88e6xxx DSA driver to configure a port's Layer 2 Policy Control List
(PCL) supported by models such as 88E6352 and 88E6390 and equivalent.

This allows to configure a port to discard frames based on a configured
destination or source MAC address and an optional VLAN, with e.g.:

    # ethtool --config-nfc lan1 flow-type ether src 00:11:22:33:44:55 action -1
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the .get_rxnfc and .set_rxnfc DSA operations to configure
a port's Layer 2 Policy Control List (PCL) via ethtool.

Currently only dropping frames based on MAC Destination or Source
Address (including the option VLAN parameter) is supported.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a new .port_set_policy operation to configure a port's
Policy Control List, based on mapping such as DA, SA, Etype and so on.

Models similar to 88E6352 and 88E6390 are supported at the moment.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell has different values for the state of a MAC address,
depending on its multicast bit. This patch completes the definitions
for these states.

At the same time, use 0 which is intuitive enough and simplifies the
code a bit, instead of the UC or MC unused value.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate the array modes on the stack but instead make it
static const. Makes the object code smaller by 303 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  51240	   5008	   1312	  57560	   e0d8 mellanox/mlx4/en_ethtool.o

After:
   text	   data	    bss	    dec	    hex	filename
  50937	   5008	   1312	  57257	   dfa9	mellanox/mlx4/en_ethtool.o

(gcc version 9.2.1, amd64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2019-09-09

This series contains a variety of cold and hot savoury changes to Intel
drivers.  Some of the fixes could be considered for stable even though
the author did not request it.

Hulk Robert cleans up (i.e. removes) a function that has no caller for
the iavf driver.

Radoslaw fixes an issue when there is no link in the VM after the
hypervisor is restored from a low-power state due to the driver not
properly restoring features in the device that had been disabled during
the suspension for ixgbevf.

Kai-Heng Feng modified e1000e to use mod_delayed_work() to help resolve
a hot plug speed detection issue by adding a deterministic 1 second
delay before running watchdog task after an interrupt.

Sasha moves functions around to avoid forward declarations, since the
forward declarations are not necessary for these static functions in
igc.  Also added a check for igc during driver probe to validate the NVM
checksum.  Cleaned up code defines that were not being used in the igc
driver.  Adds support for IP generic transmit checksum offload in the
igc driver.

Updated the iavf kernel documentation by a developer with no life.

Jake provides another fm10k update to a local variable for ease of code
readability.

Mitch fixes the iavf driver to allow the VF to override the MAC address
set by the host, if the VF is in "trusted" mode.

Mauro S. M. Rodrigues provides several changes for i40e driver, first
with resolving hw_dbg usage and referencing a i40e_hw attribute.  Also
implemented a debug macro using pr_debug, since the use of netdev_dbg
could cause a NULL pointer dereference during probe.  Finally cleaned up
code that is no longer used or needed.

Firo Yang provides a change in the ixgbe driver to ensure we sync the
first fragment unconditionally to help resolve an issue seen in the XEN
environment when the upper network stack could receive an incomplete
network packet.

Mariusz adds a missing device to the i40e PCI table in the driver.

v2: Mauro S. M. Rodrigues updated patches 10 & 11 of the series based on
    feedback from Jakub Kicinski.  Also updated patch 13 description so
    that the "Fixes:" tag was no wrapped.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add I40E_DEV_ID_10G_BASE_T_BC to i40e_pci_tbl
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add IP generic TX checksum offload functionality.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In Xen environment, if Xen-swiotlb is enabled, ixgbe driver
could possibly allocate a page, DMA memory buffer, for the first
fragment which is not suitable for Xen-swiotlb to do DMA operations.
Xen-swiotlb have to internally allocate another page for doing DMA
operations. This mechanism requires syncing the data from the internal
page to the page which ixgbe sends to upper network stack. However,
since commit f3213d93 ("ixgbe: Update driver to make use of DMA
attributes in Rx path"), the unmap operation is performed with
DMA_ATTR_SKIP_CPU_SYNC. As a result, the sync is not performed.
Since the sync isn't performed, the upper network stack could receive
a incomplete network packet. By incomplete, it means the linear data
on the first fragment(between skb->head and skb->end) is invalid. So
we have to copy the data from the internal xen-swiotlb page to the page
which ixgbe sends to upper network stack through the sync operation.

More details from Alexander Duyck:
Specifically since we are mapping the frame with
DMA_ATTR_SKIP_CPU_SYNC we have to unmap with that as well. As a result
a sync is not performed on an unmap and must be done manually as we
skipped it for the first frag. As such we need to always sync before
possibly performing a page unmap operation.

Fixes: f3213d93 ("ixgbe: Update driver to make use of DMA attributes in Rx path")
Signed-off-by: NFiro Yang <firo.yang@suse.com>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit
'5098850c ("i40e/i40evf: i40e_register.h updates")'
it is no longer possible to trigger an EMP Reset from debugfs, but it's
possible to request it either way, to end up with a bad reset request:

echo empr > /sys/kernel/debug/i40e/0002\:01\:00.1/command
i40e 0002:01:00.1: debugfs: forcing EMPR
i40e 0002:01:00.1: bad reset request 0x00010000

So let's remove this piece of code and show the available valid commands
as it is when any invalid command is issued.
Signed-off-by: N"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are several uses of hw_dbg in the code, producing no output. This
patch implements it using dev_debug.

Initially the intention was to implement it using netdev_dbg, analogously
to what is done in ixgbe for instance. That approach was avoided due to
some early usages of hw_dbg, like i40e_pf_reset, before the VSI structure
initialization causing NULL pointer dereference during the driver probe if
the debug messages were turned on as soon as the module is probed.

v2:
 - Use dev_dbg instead of pr_debug, and take advantage of dev_name
instead of crafting pretty much the same device name locally as suggested
by Jakub Kicinski.
Signed-off-by: N"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The mentioned function references a i40e_hw attribute, as parameter for
hw_dbg, but it doesn't exist in the function scope.
Fixes it by changing  parameters from i40e_hmc_info to i40e_hw which can
retrieve the necessary i40e_hmc_info.

v2:
 - Fixed reverse xmas tree code style issue as suggested by Jakub Kicinski
Signed-off-by: N"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

PCIe device control 2 defines does not use internally.
This patch comes to clean up those.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow the VF to override the "permanent" MAC address set by the host.
This allows bonding to work in the case where the administrator has set
the VF MAC.

Note that the VF must still be set to Trusted on the host if this change
is to be accepted by the PF driver.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add NVM checksum validation during probe functionality.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the function fm10k_xmit_frame_ring, we recently switched to using
the skb_frag_size accessor instead of directly using the size member of
the skb fragment.

This made the for loop slightly harder to read because it created a very
long line that is difficult to split up. Avoid this by using a local
variable in the for loop, so that we do not have to break the line on an
open parenthesis.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the LAN driver documentation to include the latest feature
implementation and driver capabilities.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

Move igc_phy_setup_autoneg, igc_wait_autoneg and igc_set_fc_watermarks
up to avoid forward declaration.
It is not necessary to forward declare these static methods.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After hot plugging an 1Gbps Ethernet cable with 1Gbps link partner, the
MII_BMSR may report 10Mbps, renders the network rather slow.

The issue has much lower fail rate after commit 59653e64 ("e1000e:
Make watchdog use delayed work"), which essentially introduces some
delay before running the watchdog task.

But there's still a chance that the hot plugging event and the queued
watchdog task gets run at the same time, then the original issue can be
observed once again.

So let's use mod_delayed_work() to add a deterministic 1 second delay
before running watchdog task, after an interrupt.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixed issue in VM which shows no link when hypervisor is
restored from low-power state. The driver is responsible for re-enabling
any features of the device that had been disabled during suspend calls,
such as IRQs and bus mastering.
Signed-off-by: NRadoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is no caller of function iavf_debug_d() in tree since
commit 75051ce4 ("iavf: Fix up debug print macro"),
so it can be removed.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jakub Kicinski says:

====================
net/tls: small TX offload optimizations

This set brings small TLS TX device optimizations. The biggest
gain comes from fixing a misuse of non temporal copy instructions.
On a synthetic workload modelled after customer's RFC application
I see 3-5% percent gain.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike normal TCP code TLS has to touch the cache lines
it copies into to fill header info. On memory-heavy workloads
having non temporal stores and normal accesses targeting
the same cache line leads to significant overhead.

Measured 3% overhead running 3600 round robin connections
with additional memory heavy workload.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For TLS device offload the tag/message authentication code are
filled in by the device. The kernel merely reserves space for
them. Because device overwrites it, the contents of the tag make
do no matter. Current code tries to save space by reusing the
header as the tag. This, however, leads to an additional frag
being created and defeats buffer coalescing (which trickles
all the way down to the drivers).

Remove this optimization, and try to allocate the space for
the tag in the usual way, leave the memory uninitialized.
If memory allocation fails rewind the record pointer so that
we use the already copied user data as tag.

Note that the optimization was actually buggy, as the tag
for TLS 1.2 is 16 bytes, but header is just 13, so the reuse
may had looked past the end of the page..
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>