The gm7113c chip is similar to the original saa7113 chip, so I try to
re-use most of the saa7113 specific setup-/configuration registers.
According to the datasheet, the gm7113c chip has not implemented
any register-addresses after 0x1f, so I add a new entry to for the chip
to the saa711x_has_reg function.
The devices I've seen using this chip will fail to get stable video-sync
if these registers are not zeroed:
	R_14_ANAL_ADC_COMPAT_CNTL
	R_15_VGATE_START_FID_CHG
	R_16_VGATE_STOP
	R_17_MISC_VGATE_CONF_AND_MSB
The saa711x_set_v4lstd is updated to send a simpler configuration-table
to avoid setting these registers.
Signed-off-by: NJon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adds a code that (auto)detects gm7113c clones. The auto-detection
here is not perfect, as, on contrary to what it would be expected
by looking into its datasheets some devices would return, instead:
	saa7115 0-0025: chip 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 @ 0x4a is unknown
(found on a device labeled as GM7113C 1145 by Ezequiel Garcia)
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: NJon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As we're now seeing other variants from chinese clones, like
gm1113c, we'll need to add more bits at the detection code.
So, move it into a separate function.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: NJon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

copy_to_user() must not be called with spinlocks held, but it is in
fmc_transfer_rds_from_internal_buff().
The patch copies data to tmpbuf, releases spinlock and then passes it to userspace.
By the way there is a small unification: replace a couple of hardcoded constants by a macro.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of falling back to 1/25 (PAL) or 1/30 (NTSC).
Signed-off-by: NIsmael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch enables tvp7002 decoder driver for media controller
based usage by adding v4l2_subdev_pad_ops  operations support
for enum_mbus_code, set_pad_format, get_pad_format and media_entity_init()
on probe and media_entity_cleanup() on remove.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NLeonid Kegulskiy <leo@lumanate.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NLeonid Kegulskiy <leo@lumanate.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes checkpatch warning to avoid CamelCase.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: NJakob Haufe <sur5r@sur5r.net>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This adds the keytable for the remote that comes with the Delock 61959.
NEC protocol with address 0x866b.
Signed-off-by: NJakob Haufe <sur5r@sur5r.net>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Those are automatically updated using the cardlist script.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

this patch moves the displaying out error case  "VPIF IRQ request failed\n"
when there is actual request_irq() fail.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

this patch removes unwanted header file inclusion and sorts
header alphabetically.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIsmael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.

[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

More dv_timings ioctl ops are introduced in video core.
Add query_dv_timings/enum_dv_timings accordingly.
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a proper card entry for this device, rather than abusing entries that are
not-quite-right.
Regards,
	Hans
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the devm_gpio_request_one() managed function to simplify cleanup
code paths.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the devm_gpio_request_one() managed function to simplify cleanup
code paths.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Using the managed function the free_irq() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Using the managed function the regulator_bulk_put() calls can be removed
from the probe error path and the remove handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Using the managed function the gpio_free() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replace gpio_request() with gpio_request_one() and remove the associated
gpio_direction_output() calls.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The tvp514x data structure is allocated using devm_kzalloc(). Freeing it
explictly would result in a double free. Fix it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The control handler must be freed in the probe error path and in the
remove handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replace the manual validity checks for the reset GPIO with the
gpio_is_valid() function.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The mt9p031 driver first accesses the I2C device in its .registered()
method. While doing that it first powers the device up, but if probing
fails, it doesn't power the chip back down. This patch fixes that bug.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Linux 3.10-rc1

* tag 'v3.10-rc1': (11697 commits)
  Linux 3.10-rc1
  [SCSI] qla2xxx: Update firmware link in Kconfig file.
  [SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
  [SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
  [SCSI] pm80xx: thermal, sas controller config and error handling update
  [SCSI] pm80xx: NCQ error handling changes
  [SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
  [SCSI] pm80xx: Changed module name and debug messages update
  [SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
  [SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
  [SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
  [SCSI] pm80xx: MSI-X implementation for using 64 interrupts
  [SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
  [SCSI] pm80xx: Multiple inbound/outbound queue configuration
  [SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
  [SCSI] lpfc: fix up Kconfig dependencies
  [SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
  dm cache: set config value
  dm cache: move config fns
  dm thin: generate event when metadata threshold passed
  ...

Pull tracing/kprobes update from Steven Rostedt:
 "The majority of these changes are from Masami Hiramatsu bringing
  kprobes up to par with the latest changes to ftrace (multi buffering
  and the new function probes).

  He also discovered and fixed some bugs in doing so.  When pulling in
  his patches, I also found a few minor bugs as well and fixed them.

  This also includes a compile fix for some archs that select the ring
  buffer but not tracing.

  I based this off of the last patch you took from me that fixed the
  merge conflict error, as that was the commit that had all the changes
  I needed for this set of changes."

* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Support soft-mode disabling
  tracing/kprobes: Support ftrace_event_file base multibuffer
  tracing/kprobes: Pass trace_probe directly from dispatcher
  tracing/kprobes: Increment probe hit-count even if it is used by perf
  tracing/kprobes: Use bool for retprobe checker
  ftrace: Fix function probe when more than one probe is added
  ftrace: Fix the output of enabled_functions debug file
  ftrace: Fix locking in register_ftrace_function_probe()
  tracing: Add helper function trace_create_new_event() to remove duplicate code
  tracing: Modify soft-mode only if there's no other referrer
  tracing: Indicate enabled soft-mode in enable file
  tracing/kprobes: Fix to increment return event probe hit-count
  ftrace: Cleanup regex_lock and ftrace_lock around hash updating
  ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
  ftrace: Have ftrace_regex_write() return either read or error
  tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
  tracing: Don't succeed if event_enable_func did not register anything
  ring-buffer: Select IRQ_WORK

Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - More fixes in the vCPU PVHVM hotplug path.
 - Add more documentation.
 - Fix various ARM related issues in the Xen generic drivers.
 - Updates in the xen-pciback driver per Bjorn's updates.
 - Mask the x2APIC feature for PV guests.

* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/pci: Used cached MSI-X capability offset
  xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
  xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
  xen: mask x2APIC feature in PV
  xen: SWIOTLB is only used on x86
  xen/spinlock: Fix check from greater than to be also be greater or equal to.
  xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
  xen/vcpu: Document the xen_vcpu_info and xen_vcpu
  xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.

Pull second SCSI update from James "Jaj B" Bottomley:
 "This is the final round of SCSI patches for the merge window.  It
  consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
  be2iscsi, pm80xx, qla4x and ipr).

  There's also the power management updates that complete the patches in
  Jens' tree, an iscsi refcounting problem fix from the last pull, some
  dif handling in scsi_debug fixes, a few nice code cleanups and an
  error handling busy bug fix."

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
  [SCSI] qla2xxx: Update firmware link in Kconfig file.
  [SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
  [SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
  [SCSI] pm80xx: thermal, sas controller config and error handling update
  [SCSI] pm80xx: NCQ error handling changes
  [SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
  [SCSI] pm80xx: Changed module name and debug messages update
  [SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
  [SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
  [SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
  [SCSI] pm80xx: MSI-X implementation for using 64 interrupts
  [SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
  [SCSI] pm80xx: Multiple inbound/outbound queue configuration
  [SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
  [SCSI] lpfc: fix up Kconfig dependencies
  [SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
  [SCSI] sd: change to auto suspend mode
  [SCSI] sd: use REQ_PM in sd's runtime suspend operation
  [SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
  [SCSI] ufs: Correct the expected data transfersize
  ...

Pull idle update from Len Brown:
 "Add support for new Haswell-ULT CPU idle power states"

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  intel_idle: initial C8, C9, C10 support
  tools/power turbostat: display C8, C9, C10 residency

Pull audit changes from Eric Paris:
 "Al used to send pull requests every couple of years but he told me to
  just start pushing them to you directly.

  Our touching outside of core audit code is pretty straight forward.  A
  couple of interface changes which hit net/.  A simple argument bug
  calling audit functions in namei.c and the removal of some assembly
  branch prediction code on ppc"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: fix message spacing printing auid
  Revert "audit: move kaudit thread start from auditd registration to kaudit init"
  audit: vfs: fix audit_inode call in O_CREAT case of do_last
  audit: Make testing for a valid loginuid explicit.
  audit: fix event coverage of AUDIT_ANOM_LINK
  audit: use spin_lock in audit_receive_msg to process tty logging
  audit: do not needlessly take a lock in tty_audit_exit
  audit: do not needlessly take a spinlock in copy_signal
  audit: add an option to control logging of passwords with pam_tty_audit
  audit: use spin_lock_irqsave/restore in audit tty code
  helper for some session id stuff
  audit: use a consistent audit helper to log lsm information
  audit: push loginuid and sessionid processing down
  audit: stop pushing loginid, uid, sessionid as arguments
  audit: remove the old depricated kernel interface
  audit: make validity checking generic
  audit: allow checking the type of audit message in the user filter
  audit: fix build break when AUDIT_DEBUG == 2
  audit: remove duplicate export of audit_enabled
  Audit: do not print error when LSMs disabled
  ...