The HP pin (0x16) control has to be changed dynamically depending on
the master volume switch as well as the speaker pin (0x1a).  Otherwise
the headphone still sounds with master off.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixed the wrongly set up for SPDIF output on Conexant 5051 codec.
It must point to the audio out widget instead of a pin.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Initialize the mic ports B & C on Conexant 5051 codec dynamically
according to the mic jack detection, instead of static init arrays.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

All cx5051 codec models have the same Master playback mixer definitions.
Merge them together.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the support for Toshiba Satellite M300 with Conexant 5051 codec.
Since the laptop has no port C connection and the pin reports always
the jack sense true, we need to ignore port-C unsol event.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use the standard "Capture" mixer name for HP dv6736 with Cxt5051 codec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Minor fixes for HP Compaq Presario F700 quirks with Cxt5051 codec:
- changed the capture mixer elements to the standard name.
- fixed the quirk name string without a space
- sorted the quirk list
- updated the documentation
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some codecs disable widgets used for output pins and reserve as vendor-
spec widgets.  Thus we need to check the widget type and pin cap before
actually sending SET_EAPD verbs in the auto-configuration mode.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC259 has a widget NID 0x21 for the output pin, but it wasn't handled
properly in alc268_new_analog_output().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Sony VAIO VGN-P11G with ALC262 codec has only one input pin, and the
recording doesn't work with model=auto because ALC262 parser sets the
wrong cap NIDs to choose the route and the default route for the sole
input pin wasn't initialized properly.  This patch solves these issues.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On my laptop (HP dv6-1110ax), there are no OEM strings in SMBIOS of type
"HP_Mute_LED*". Hence, the GPIO for the mute button LED doesn't get set
properly. I didn't find the strings in my cousin's laptop (HP dv9500t CTO)
either.

As per the documentation of find_mute_led_gpio(), these strings occur
in HP B-series systems - so, before scanning the SMBIOS strings, we need to
check if we're dealing with a B-series system.
Need to get confirmation from HP if this logic takes care of all the
systems. I'm trying to poke a friend there.
Signed-off-by: NKunal Gangakhedkar <kunal.gangakhedkar@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The capture-related mixer elements are missing with ALC861/ALC660 codecs
when quirks are present, due to missing call of set_capture_mixer().

Reference: Novell bnc#567340
	http://bugzilla.novell.com/show_bug.cgi?id=567340Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

This patch adds support for automatically muting the speakers when headphones
are inserted, as well as relabelling the headphone widgets from the
non-standard "HP" to the standard "Headphone" for the mb5 model.
Signed-off-by: NAlex Murray <murray.alex@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The alc664-mode4 model doesn't seem to fit with Toshiba NB205 correctly.
NB205 uses the pin 0x17 connected with the mixer 0x0f for the speaker
output, which isn't controlled by mode4 model at all.
Rather model=auto works fine as is on the latest driver, so let it back
again.
Tested-by: NNickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds the Intel Cougar Point (PCH) HD Audio Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The capture source or input source mixer element wasn't created properly
for ALC861-VD codec due to the wrong NID passed to
alc_auto_create_input_ctls().

References: Novell bnc#568305
	http://bugzilla.novell.com/show_bug.cgi?id=568305Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

Add the STMicroelectronics ST7597 codec and an unknown codec
from the same manufacturer found on the Creative SB 128 card (CT4810).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This model needs both 'Headphone Jack Sense' and 'Line Jack Sense' muted
for audible playback, so just add it to the ad1981 jack sense blacklist.

Cc: stable@kernel.org
Tested-by: NPete <x41215201@gmail.com>
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

We need to set the LRCLK inversion bit to select DSP mode.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

The patch "sbawe: fix memory detection" fixed detection
for memoryless SB32 cards but broke detection of memory
above 512KB. This patch fixes the regression.

The patch has been tested on the SB32 card (CT3670) with
0MB, 2MB and 8MB memory installed.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The problem is that in the original code sound_nblocks could go up to 1024
which would be an array overflow.

This was found with a static checker and has been compile tested only.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The XO's audio hardware is wired up to allow DC sensors (e.g. light
sensors, thermistors, etc) to be plugged in through the microphone jack.

Add sound mixer controls to allow this mode to be enabled and tweaked.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The XO-1.5 has a microphone LED designed to indicate to the user when
something is being recorded.

This light is controlled by the microphone bias voltage and it is
currently coming on all the time.

This patch defers the microphone port configuration until when recording
is actually taking place, fixing the behaviour of the LED.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added patch for Hewlett-Packard Company Device Subsystem id - 103c:30ea.
Signed-off-by: NKen Prox <kprox@users.sourceforge.net>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The WM9705 and WM9703 ops are the same actually so use
the same code for both.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

When runtime->periods == 1 or when pointer crosses end of ring buffer,
the delta might be greater than buffer_size.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

As noted by pl bossart <bossart.nospam@gmail.com>, the PCM I/O routines
(snd_pcm_lib_write1, snd_pcm_lib_read1) should block wake_up() calls
until all samples are not processed.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Do general cleanup in snd_pcm_update_hw_ptr*() routines and merge them.
The main change is hw_ptr_interrupt variable removal to simplify code
logic. This variable can be computed directly from hw_ptr.

Ensure that updated hw_ptr is not lower than previous one (it was possible
with old code in some obscure situations when interrupt was delayed or
the lowlevel driver returns wrong ring buffer position value).
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

In some debug cases, it might be usefull to see previous ring buffer
positions to determine position problems from the lowlevel drivers.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

To increase code readability, convert send xrun_debug() argument to
use defines.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Initialize the glue by calling snd_soc_new_ac97_codec() as is done
in other ASoC AC97 codecs.  Fixes an oops caused by dereferencing
uninitialized members in snd_soc_new_pcms().

Run-tested on Au1250.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As the release of substreams may be done asynchronously from the
disconnection, close callback needs to check the shutdown flag before
actually accessing the usb interface.

Reference: Novell bnc#505027
	http://bugzilla.novell.com/show_bug.cgi?id=565027Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch converts the alc889 Aspire-specific powerdown to a generic
one. Like the previous effort, it currently only handles Front and PCM
but can be easily extended to cover other nids. The existing hook for
alc889 Aspire-specific remains enabled. Upon further testing, I've added
its use for ALC861_AUTO as well. Following patches will enable them for
other quirks.
Tested-by: NDr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch ports powerdown fixes to AD198x. Currently we only turn off
Front and HP for suspend, but this is easily extended for additional
nids.
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

With `while (i++ < MAX_WRITE_RETRY)' i reaches MAX_WRITE_RETRY + 1 after the loop
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://bugs.launchpad.net/ubuntu/+bug/498863

This mainboard needs ac97_codec=0.

Cc: stable@kernel.org
Tested-by: NApoorv Parle <apparle@yahoo.co.in>
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Rewrite the codes to use strict_strtoul() instead of simple_strtoul().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Check whether the given NID is a pin widget before storing the
user-defined pin configs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Call snd_hda_shutup_pins() at suspend and free for avoiding click noises.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a common helper function for clearing pin controls before suspend.
Use the pincfg array instead of looking through all widget tree.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>