At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.

Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.

Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

It makes it a bit easier to read and understand the code that deals with
balancing the 16 aggregation codes among the ports in a certain LAG.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.

In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The setup of logical port IDs is done in two places: from the inconclusively
named ocelot_setup_lag and from ocelot_port_lag_leave, a function that
also calls ocelot_setup_lag (which apparently does an incomplete setup
of the LAG).

To improve this situation, we can rename ocelot_setup_lag into
ocelot_setup_logical_port_ids, and drop the "lag" argument. It will now
set up the logical port IDs of all switch ports, which may be just
slightly more inefficient but more maintainable.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The index of the LAG is equal to the logical port ID that all the
physical port members have, which is further equal to the index of the
first physical port that is a member of the LAG.

The code gets a bit carried away with logic like this:

	if (a == b)
		c = a;
	else
		c = b;

which can be simplified, of course, into:

	c = b;

(with a being port, b being lp, c being lag)

This further makes the "lp" variable redundant, since we can use "lag"
everywhere where "lp" (logical port) was used. So instead of a "c = b"
assignment, we can do a complete deletion of b. Only one comment here:

		if (bond_mask) {
			lp = __ffs(bond_mask);
			ocelot->lags[lp] = 0;
		}

lp was clobbered before, because it was used as a temporary variable to
hold the new smallest port ID from the bond. Now that we don't have "lp"
any longer, we'll just avoid the temporary variable and zeroize the
bonding mask directly.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.

We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

IPv6 header information is not currently part of the entropy source for
the 4-bit aggregation code used for LAG offload, even though it could be.
The hardware reference manual says about these fields:

ANA::AGGR_CFG.AC_IP6_TCPUDP_PORT_ENA
Use IPv6 TCP/UDP port when calculating aggregation code. Configure
identically for all ports. Recommended value is 1.

ANA::AGGR_CFG.AC_IP6_FLOW_LBL_ENA
Use IPv6 flow label when calculating AC. Configure identically for all
ports. Recommended value is 1.

Integration with the xmit_hash_policy of the bonding interface is TBD.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Since switchdev/DSA exposes network interfaces that fulfill many of the
same user space expectations that dedicated NICs do, it makes sense to
not deny bonding interfaces with a bonding policy that we cannot offload,
but instead allow the bonding driver to select the egress interface in
software.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Make ocelot's net device event handler more streamlined by structuring
it in a similar way with others. The inspiration here was
dsa_slave_netdevice_event.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

ocelot_netdevice_port_event treats a single event, NETDEV_CHANGEUPPER.
So we can remove the check for the type of event, and rename the
function to be more suggestive, since there already is a function with a
very similar name of ocelot_netdevice_event.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The max qset number is a fixed value now and it is defined by a macro.
In order to support other value in different kinds of device, it is
better to use specification queried from firmware to replace macro.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

In order to add a method to check the specification of max tm rate
for debugging, function hns3_dbg_dev_specs() adds this value print.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Since the newer hardware may supports different frame size,
so add support to obtain the capability from the firmware
instead of the fixed value.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

When update the TC info for NIC, there are some differences
between PF and VF. Currently, four "vport->vport_id" are
used to distinguish PF or VF. So merge them into one to
improve readability and maintainability of code.
Signed-off-by: NGuoJia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

As RSS indirection table size may be different in different
hardware. Instead of using macro, this value is better to use
device specification which querying from firmware.

BTW, RSS indirection table should be allocated by the queried
size instead the static array.

.get_rss_indir_size in struct hnae3_ae_ops is not used now,
so remove it as well.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

To improve the compatibility of firmware for driver, help firmware
to deal with different api commands, add api capability bits when
initialize the command queue.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Add support for backplane link mode, which is, according to discussions
with NXP earlier in the year, is a mode where the OS (Linux) is able to
manage the PCS and Serdes itself.

This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Now that pcs-lynx supports 1000BASE-X, add support for this interface
mode to dpaa2-mac. pcs-lynx can be switched at runtime between SGMII
and 1000BASE-X mode, so allow dpaa2-mac to switch between these as
well.

This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Reviewed-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Add support for 1000BASE-X to pcs-lynx for the LX2160A.

This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Reviewed-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This converts the driver to use the new tasklet API introduced in
commit 12cc923f ("tasklet: Introduce new initialization API")

The new API changes the argument passed to callback functions,
but fortunately it is unused so it is straight forward to use
DECLARE_TASKLET rather than DECLARE_TASLKLET_OLD.
Signed-off-by: NEmil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204173947.92884-1-kernel@esmil.dkSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Reviewed-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Tested-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

There is a spelling mistake in the function name alloc_channles_and_rings.
Fix this by renaming it to alloc_channels_and_rings.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210204094944.51460-1-colin.king@canonical.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

When device side MTU is larger than host side MTU, the packets
(typically rmnet packets) are split over multiple MHI transfers.
In that case, fragments must be re-aggregated to recover the packet
before forwarding to upper layer.

A fragmented packet result in -EOVERFLOW MHI transaction status for
each of its fragments, except the final one. Such transfer was
previously considered as error and fragments were simply dropped.

This change adds re-aggregation mechanism using skb chaining, via
skb frag_list.

A warning (once) is printed since this behavior usually comes from
a misconfiguration of the device (e.g. modem MTU).
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/1612428002-12333-1-git-send-email-loic.poulain@linaro.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

There is no guarantee that rmnet rx_handler is only fed with linear
skbs, but current rmnet implementation does not check that, leading
to crash in case of non linear skbs processed as linear ones.

Fix that by ensuring skb linearization before processing.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Acked-by: NWillem de Bruijn <willemb@google.com>
Reviewed-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1612428002-12333-2-git-send-email-loic.poulain@linaro.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Align netdevice statistics when the device is running in XDP mode
to other upstream drivers. In particular report to user-space rx
packets even if they are not forwarded to the networking stack
(XDP_PASS) but if they are redirected (XDP_REDIRECT), dropped (XDP_DROP)
or sent back using the same interface (XDP_TX). This patch allows the
system administrator to verify the device is receiving data correctly.
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a457cb17dd9c58c116d64ee34c354b2e89c0ff8f.1612375372.git.lorenzo@kernel.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Fix the following coccicheck warnings:

./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1651:36-38: WARNING
!A || A && B is equivalent to !A || B.
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Signed-off-by: NJiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1612260157-128026-1-git-send-email-jiapeng.chong@linux.alibaba.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Fix the typo.
Signed-off-by: NAndrea Parri (Microsoft) <parri.andrea@gmail.com>
Fixes: 0ba35fe9 ("hv_netvsc: Copy packets sent by Hyper-V out of the receive buffer")
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The recv_buf buffers are allocated in netvsc_device_add().  Later in
netvsc_init_buf() the response to NVSP_MSG1_TYPE_SEND_RECV_BUF allows
the host to set up a recv_section_size that could be bigger than the
(default) value used for that allocation.  The host-controlled value
could be used by a malicious host to bypass the check on the packet's
length in netvsc_receive() and hence to overflow the recv_buf buffer.

Move the allocation of the recv_buf buffers into netvsc_init_but().
Reported-by: NJuan Vazquez <juvazq@microsoft.com>
Signed-off-by: NAndrea Parri (Microsoft) <parri.andrea@gmail.com>
Fixes: 0ba35fe9 ("hv_netvsc: Copy packets sent by Hyper-V out of the receive buffer")
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.

Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().

The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

On read, master should send 31 MSB of the register (only even values
are ever used), followed by a 1 to indicate read. Then, reading two
bytes, the device will output the register's value.

On write, master sends 31 MSB of the register, followed by a 0 to
indicate write, followed by two bytes containing the register value.

Flexibilis' documentation (version 1.3) specifies the opposite
polarity (#read/write), but the scope indicates that it is, in fact,
read/#write.
Signed-off-by: NTobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: NGeorge McCollister <george.mccollister@gmail.com>
Link: https://lore.kernel.org/r/20210202191645.439-1-tobias@waldekranz.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The flow steering struct ethtool_flow_ext::data field is __be32, so when
the CFP code needs to check the VLAN egress tagging attribute in bit 0,
it does this in CPU native endianness. So logically, the endianness
conversion is set up the other way around, although in practice the same
result is produced.

Gets rid of build warning:

warning: cast from restricted __be32
warning: incorrect type in argument 1 (different base types)
   expected unsigned int [usertype] val
   got restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: restricted __be32 degrades to integer
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210203193918.2236994-1-olteanv@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

s/initialsation/initialisation/
s/specifiing/specifying/
Signed-off-by: NBhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210204031648.27300-1-unixbhaskar@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The null check of filp->f_path.dentry->d_iname is redundant because
it is an array of DNAME_INLINE_LEN chars and cannot be a null. Fix
this by removing the null check.

Addresses-Coverity: ("Array compared against 0")
Fixes: 04987ca1 ("net: hns3: add debugfs support for tm nodes, priority and qset info")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210203131040.21656-1-colin.king@canonical.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

When enabling encap for a ipv6 socket without udp_encap_needed_key
increased, UDP GRO won't work for v4 mapped v6 address packets as
sk will be NULL in udp4_gro_receive().

This patch is to enable it by increasing udp_encap_needed_key for
v6 sockets in udp_tunnel_encap_enable(), and correspondingly
decrease udp_encap_needed_key in udpv6_destroy_sock().

v1->v2:
  - add udp_encap_disable() and export it.
v2->v3:
  - add the change for rxrpc and bareudp into one patch, as Alex
    suggested.
v3->v4:
  - move rxrpc part to another patch.
Acked-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Traditionally loopback devices come up with initial state as DOWN for
any new network-namespace. This would mean that anyone needing this
device would have to bring this UP by issuing something like 'ip link
set lo up'. This can be avoided if the initial state is set as UP.
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NJian Yang <jianyang@google.com>
Link: https://lore.kernel.org/r/20210201233445.2044327-1-jianyang.kernel@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: NDavid Rientjes <rientjes@google.com>
Suggested-by: NJakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: NAlexander Lobakin <alobakin@pm.me>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Fix the following coccicheck warnings:

./drivers/net/xen-netfront.c:1816:52-54: WARNING !A || A && B is
equivalent to !A || B.
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Signed-off-by: NJiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/1612261069-13315-1-git-send-email-jiapeng.chong@linux.alibaba.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Based on work by Pravin Shelar.

Update appropriate stats when packet transmission isn't possible.
Signed-off-by: NJonas Bonn <jonas@norrbonn.se>
Acked-by: NHarald Welte <laforge@gnumonks.org>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>