Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 23 7月, 2018 1 次提交
  3. 13 7月, 2018 2 次提交
  5. 28 6月, 2018 1 次提交
  7. 22 6月, 2018 1 次提交
    • J
      nvme-pci: limit max IO size and segments to avoid high order allocations · 943e942e
      由 Jens Axboe 提交于 
      nvme requires an sg table allocation for each request. If the request
is large, then the allocation can become quite large. For instance,
with our default software settings of 1280KB IO size, we'll need
10248 bytes of sg table. That turns into a 2nd order allocation,
which we can't always guarantee. If we fail the allocation, blk-mq
will retry it later. But there's no guarantee that we'll EVER be
able to allocate that much contigious memory.

Limit the IO size such that we never need more than a single page
of memory. That's a lot faster and more reliable. Then back that
allocation with a mempool, so that we know we'll always be able
to succeed the allocation at some point.
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Acked-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
      943e942e
  9. 21 6月, 2018 2 次提交
  11. 20 6月, 2018 5 次提交
  13. 15 6月, 2018 3 次提交
  15. 14 6月, 2018 4 次提交
    • C
      nvme: remove nvme_reinit_tagset · 14dfa400
      由 Christoph Hellwig 提交于 
      Unused now that all transports stopped using it.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJens Axboe <axboe@kernel.dk>
      14dfa400
    • J
      nvme-fc: fix nulling of queue data on reconnect · 3e493c00
      由 James Smart 提交于 
      The reconnect path is calling the init routines to clear a queue
structure. But the queue structure has state that perhaps needs
to persist as long as the controller is live.

Remove the nvme_fc_init_queue() calls on reconnect.
The nvme_fc_free_queue() calls will clear state bits and reset
any relevant queue state for a new connection.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
      3e493c00
    • J
      nvme-fc: remove reinit_request routine · 587331f7
      由 James Smart 提交于 
      The reinit_request routine is not necessary. Remove support for the
op callback.

As all that nvme_reinit_tagset() does is itterate and call the
reinit routine, it too has no purpose. Remove the call.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
      587331f7
    • J
      nvme-fc: change controllers first connect to use reconnect path · 4c984154
      由 James Smart 提交于 
      Current code follows the framework that has been in the transports
from the beginning where initial link-side controller connect occurs
as part of "creating the controller". Thus that first connect fully
talks to the controller and obtains values that can then be used in
for blk-mq setup, etc. It also means that everything about the
controller is fully know before the "create controller" call returns.

This has several weaknesses:
- The initial create_ctrl call made by the cli will block for a long
  time as wire transactions are performed synchronously. This delay
  becomes longer if errors occur or connectivity is lost and retries
  need to be performed.
- Code wise, it means there is a separate connect path for initial
  controller connect vs the (same) steps used in the reconnect path.
- And as there's separate paths, it means there's separate error
  handling and retry logic. It also plays havoc with the NEW state
  (should transition out of it after successful initial connect) vs
  the RESETTING and CONNECTING (reconnect) states that want to be
  transitioned to on error.
- As there's separate paths, to recover from errors and disruptions,
  it requires separate recovery/retry paths as well and can severely
  convolute the controller state.

This patch reworks the fc transport to use the same connect paths
for the initial connection as it uses for reconnect. This makes a
single path for error recovery and handling.

This patch:
- Removes the driving of the initial connect and replaces it with
  a state transition to CONNECTING and initiating the reconnect
  thread. A dummy state transition of RESETTING had to be traversed
  as a direct transtion of NEW->CONNECTING is not allowed. Given
  that the controller is "new", the RESETTING transition is a simple
  no-op. Once in the reconnecting thread, the normal behaviors of
  ctrl_loss_tmo (max_retries * connect_delay) and dev_loss_tmo will
  apply before the controller is torn down.
- Only if the state transitions couldn't be traversed and the
  reconnect thread not scheduled, will the controller be torn down
  while in create_ctrl.
- The prior code used the controller state of NEW to indicate
  whether request queues had been initialized or not. For the admin
  queue, the request queue is always created, so there's no need to
  check a state. For IO queues, change to tracking whether a successful
  io request queue create has occurred (e.g. 1st successful connect).
- The initial controller id is initialized to the dynamic controller
  id used in the initial connect message. It will be overwritten by
  the real controller id once the controller is connected on the wire.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
      4c984154
  17. 13 6月, 2018 1 次提交
  19. 11 6月, 2018 4 次提交
  21. 09 6月, 2018 11 次提交
  23. 01 6月, 2018 5 次提交