Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 05 5月, 2015 7 次提交
  3. 29 4月, 2015 5 次提交
  5. 27 4月, 2015 1 次提交
    • M
      ath10k: implement more versatile set_bitrate_mask · 45c9abc0
      由 Michal Kazior 提交于 
      Until now only a single fixed tx rate or nss was
allowed to be set.

The patch attempts to improve this by allowing
most bitrate masks. The limitation is VHT MCS
rates cannot be expressed separately using
existing firmware interfaces and only the
following VHT MCS ranges are supported: none, 0-7,
0-8, and 0-9.

This keeps the old behaviour when requesting
single tx rate or single nss. The new bitrate mask
logic is only applied to other cases that would
return -EINVAL until now.

Depending on firmware revisions some combinations
may crash firmware so use with care, please.

This depends on "ath10k: don't use reassoc flag".
Without it key cache would effectively be
invalidated upon bitrate change leading to
communication being no longer possible.

These work:

  iw wlan0 set bitrates legacy-5 6 12 ht-mcs-5 1 2 3
  iw wlan0 set bitrates legacy-5 ht-mcs-5 7 8 9
  iw wlan0 set bitrates legacy-5 24 ht-mcs-5 vht-mcs-5 1:0-9

These won't work:

  iw wlan0 set bitrates legacy-5 ht-mcs-5 vht-mcs-5 1:0-5
  iw wlan0 set bitrates vht-mcs-5 2:7-9

(note the invalid VHT MCS ranges)
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      45c9abc0
  7. 22 4月, 2015 3 次提交
    • M
      ath10k: fix qca61x4 hw2.1 support · 11a002ef
      由 Michal Kazior 提交于 
      During initialization firmware does some sort of
memory switch between DRAM and IRAM. If
configuration value for bank switching isn't
correct device crashes during init.

The new value prevents firmware 11.0.0.302 (and
possibly others) for qca61x4 hw2.1 from crashing
during init.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      11a002ef
    • M
      ath10k: allow loading device specific board files · de57e2c8
      由 Michal Kazior 提交于 
      Some devices differ slightly and require different
board files. If wrong board data is used they
crash or behave incorrectly.

These devices can be differentiated by looking at
PCI subsystem device id. That is the case for
qca61x4 devices at least.

The board specific filename is constructed as:

 board-<bus>-<id>.bin

For PCI in particular it is:

 board-pci-<vendor>:<dev>:<subsys_vendor>:<subsys_dev>.bin

These files are looked in device/hw specific
directories. Hence for Killer 1525 (qca6174 hw2.1)
ath10k will request:

  /lib/firmware/ath10k/QCA6174/hw2.1/board-pci-168c:003e:1a56:1525.bin

To not break any existing setups (e.g. in case
some devices in the wild already have subsys ids)
if a board specific file isn't found a generic one
is used which is the one which would be used until
now. This guarantees that after upgrading a driver
device will not suddenly stop working due to
now-missing specific board file. If this is the
case a "fallback" string is appended to the info
string when driver boots.

Keep in mind this is distinct from cal-pci-*.bin
files which contain full calibration data and MAC
address. Cal data is aimed at systems where
calibration data is stored out of band, e.g. on
nand flash instead of device EEPROM - an approach
taken by some AP/router vendors.

Board files are more of a template and needs some
bits to be filled in by the OTP program using
device EEPROM contents.

One could argue to map subsystem ids to some board
design codename strings instead of using raw ids
when building the board filename. Using a mapping
however would make it a lot more cumbersome and
time consuming (due to how patches propagate over
various kernel trees) to add support for some new
device board designs. Adding a board file is a lot
quicker and doesn't require recompilation.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      de57e2c8
    • M
      ath10k: share board file loading code across FW APIs · d0ed74f3
      由 Michal Kazior 提交于 
      There's no need to implement the same thing twice.
Reduce code duplication.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      d0ed74f3
  9. 17 4月, 2015 10 次提交
  11. 15 4月, 2015 5 次提交
    • P
      ath: lower JP W53 band DFS detection threshold around 30% · 26bea13a
      由 Peter Oh 提交于 
      Japan's W53 band requires 50% data traffic during its DFS test,
but WLAN baseband used by ath9k and ath10k is not able to achieve
current threshold rate, 50%, under the data traffic rate.
In other words, HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the rate.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      26bea13a
    • P
      ath: define JP DFS patterns separated from FCC · cb3fbd63
      由 Peter Oh 提交于 
      Separate Japan's DFS pattern from FCC to control PPB threshold.

Currently all the radar detectors use the same threshold rate at
50%, but it's not able to achieve if data traffic rate is higher
than 40% because WLAN baseband used by ath9k and ath10k often fails
detecting radar pulses, so that SW cannot get enough radar reports
to achieve the rate.

Since Japan's W53 band requires 50% data traffic during its DFS
test we need to apply different threshold rate than others on it.
Hence define its own pattern to give flexibility to threshold rate.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      cb3fbd63
    • M
      ath10k: use scan burst for hw roc · dbd3f9f3
      由 Michal Kazior 提交于 
      This improves chances of getting onto a foreign
channel and thus makes P2P a bit more reliable.

Without scan burst it was possible for firmware to
not switch to foreign channel resulting in "failed
to switch to channel for roc scan" warning. This
would also effectively fail some offchan tx
requests and lead to P2P find/connect taking
longer. This could be observed when other vifs
were running/busy, e.g. with P2P GO.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      dbd3f9f3
    • M
      ath10k: fix hw roc expiration · fcf98446
      由 Michal Kazior 提交于 
      It is not guaranteed firmware will switch to
foreign channel immediately after starting scan
sequence. To account for that don't use duration
parameter for scan time. Instead request insanely
long scan and use timeout worker to cancel it from
driver.

This should improve P2P reliability a bit.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      fcf98446
    • P
      ath: support new FCC DFS Radar Type 1 · 694c0e0a
      由 Peter Oh 提交于 
      Add support for new FCC DFS rules released on August 14, 2014.
FCC has added a new radar type named Radar Type 1 and original
Radar Type 1 is renamed to Radar Type 0 in consequence.

During the certificate test, Type 1 PRI values are randomly selected
within the range of 518 and 3066 and we divide it to 3 groups based on
practical test result data collected for more than a year.

For about Radar type ID, it does nothing to functionalities.
In other words, even if we re-order the IDs, DFS detection will
work as well, but we give the ID with matching to FCC doc.

By adding this support, the drivers using this DFS function are
able to support both of old and new FCC DFS rules simultaneously
without any other changes.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      694c0e0a
  13. 09 4月, 2015 7 次提交
  15. 08 4月, 2015 2 次提交