drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
 warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
 warning: tuple_key_info defined but not used [-Wunused-const-variable=]

The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Aaro this patch causes network problems on
MIPS Loongson platform. Therefore revert it.

Fixes: f072218c ("r8169: remove not needed call to dma_sync_single_for_device")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return code value could be non deterministic in case of wrong size read.
With this patch, if such error occurs, set rc to be -EIO.

In addition, mlx5_hv_config_common() supports reading of
HV_CONFIG_BLOCK_SIZE_MAX bytes only, fix to early return error with
bad input.

Fixes: 913d14e8 ("net/mlx5: Add wrappers for HyperV PCIe operations")
Reported-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.

This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: NMarco Hartmann <marco.hartmann@nxp.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed a bug where driver was breaking out of the loop and
reporting an error without retrying first.
Signed-off-by: NMarcin Formela <marcin.formela@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: NSylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver waits after issuing a reset. When a reset takes too long a driver
gives up. Implemented by invoking PF reset in a loop. After defined
number of unsuccessful PF reset trials it returns error.
Without this patch PF reset fails when NIC is in recovery mode.

So make i40e_set_mac_type() public. i40e driver requires i40e_set_mac_type()
to be public. It is required for recovery mode handling. Without this patch
recovery mode could not be detected in i40e_probe().
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes function i40e_update_dcb_config(). Instead of
i40e_update_dcb_config() we use i40e_init_dcb(), which implements the
correct NVM read.
Signed-off-by: NGrzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add update to the VSI pointer passed to the i40e_set_vf_mac function.
If VF is in reset state the driver waits in i40e_set_vf_mac function
for the reset to be complete, yet after reset the vsi pointer
that was passed into this function is no longer valid.

The patch updates local VSI pointer directly from pf->vsi array,
by using the id stored in VF pointer (lan_vsi_idx).

Without this commit the driver might occasionally invoke general
protection fault in kernel and disable the OS entirely.
Signed-off-by: NSlawomir Laba <slawomirx.laba@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The stats structure for the VEB switch statistics is reset periodically,
but the tc_stats are not reset at the same time.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Upcoming FW increment API version to 1.9 due to Extend PHY access AQ
command support. SW is ready for that support as well.
Signed-off-by: NPiotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Function check_recovery_mode had wrong if statement.
Now we check proper FWS1B register values, which are responsible for
the recovery mode. Recovery mode has 4 values for x710 and 2 for x722.
That's why we need 6 different flags which are defined in the code.
Now in the if statement, we recognize type of mac address
and register value.
Without those changes driver could show wrong state.
Signed-off-by: NAdrian Podlawski <adrian.podlawski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds "drop mode" parameter to set mac config AQ command.
This bit controls the behavior when a no-drop packet is blocking a TC
queue.
0 – The PF driver is notified.
1 – The blocking packet is dropped and then the PF driver is notified.
Signed-off-by: NSylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes following error reported by cppcheck:
(error) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: NBeilei Xing <beilei.xing@intel.com>
Signed-off-by: NFerruh Yigit <ferruh.yigit@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When i40e_configure_tx_ring(vsi->tx_rings[i]) returns an error, we should
exit from i40e_vsi_configure_tx and return the error, instead of continuing
to check whether xdp is enable, and configure the xdp transmit ring.
Signed-off-by: Nhuhai <huhai@kylinos.cn>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to the ixgbe issue fixed in:
655c9141 ("ixgbe: Check DDM existence in transceiver before access)

i40e has the same issue when reading eeprom from SFP's module that comply
with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM)
interface described in it. The existence of such area is specified by bit
6 of byte 92, set to 1 if implemented.

Without this patch, due to not checking this bit i40e fails to read SFP
module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
Signed-off-by: N"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both
have giant structure on the stack, which makes each one use stack frames
larger than 500 bytes.

As clang decides one function into the other, we get a warning for
exceeding the frame size limit on 32-bit architectures:

drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=]

When building with gcc, the inlining does not happen, but i40e_set_fc()
calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the
kernel stack just as much.

The parts that actually use large stacks don't overlap, so make sure
each one is a separate function, and mark them as noinline_for_stack to
prevent the compilers from combining them again.

Fixes: 0a862b43 ("i40e/i40evf: Add module_types and update_link_info")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

HV VHCA stats agent is responsible on running a preiodic rx/tx
packets/bytes stats update. Currently the supported format is version
MLX5_HV_VHCA_STATS_VERSION. Block ID 1 is dedicated for statistics data
transfer from the VF to the PF.

The reporter fetch the statistics data from all opened channels, fill it
in a buffer and send it to mlx5_hv_vhca_write_agent.

As the stats layer should include some metadata per block (sequence and
offset), the HV VHCA layer shall modify the buffer before actually send it
over block 1.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Control agent is responsible over of the control block (ID 0). It should
update the PF via this block about every capability change. In addition,
upon block 0 invalidate, it should activate all other supported agents
with data requests from the PF.

Upon agent create/destroy, the invalidate callback of the control agent
is being called in order to update the PF driver about this change.

The control agent is an integral part of HV VHCA and will be created
and destroy as part of the HV VHCA init/cleanup flow.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HV VHCA is a layer which provides PF to VF communication channel based on
HyperV PCI config channel. It implements Mellanox's Inter VHCA control
communication protocol. The protocol contains control block in order to
pass messages between the PF and VF drivers, and data blocks in order to
pass actual data.

The infrastructure is agent based. Each agent will be responsible of
contiguous buffer blocks in the VHCA config space. This infrastructure will
bind agents to their blocks, and those agents can only access read/write
the buffer blocks assigned to them. Each agent will provide three
callbacks (control, invalidate, cleanup). Control will be invoked when
block-0 is invalidated with a command that concerns this agent. Invalidate
callback will be invoked if one of the blocks assigned to this agent was
invalidated. Cleanup will be invoked before the agent is being freed in
order to clean all of its open resources or deferred works.

Block-0 serves as the control block. All execution commands from the PF
will be written by the PF over this block. VF will ack on those by
writing on block-0 as well. Its format is described by struct
mlx5_hv_vhca_control_block layout.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add wrapper functions for HyperV PCIe read / write /
block_invalidate_register operations.  This will be used as an
infrastructure in the downstream patch for software communication.

This will be enabled by default if CONFIG_PCI_HYPERV_INTERFACE is set.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow tracing neigh state during neigh update task that is executed on
workqueue and is scheduled by neigh state change event.

Usage example:
 ># cd /sys/kernel/debug/tracing
 ># echo mlx5:mlx5e_rep_neigh_update >> set_event
 ># cat trace
    ...
    kworker/u48:7-2221  [009] ...1  1475.387435: mlx5e_rep_neigh_update:
netdev: ens1f0 MAC: 24:8a:07:9a:17:9a IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_connected=1

Added corresponding documentation in
    Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NDmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Allow tracing result of neigh used value update task that is executed
periodically on workqueue.

Usage example:
 ># cd /sys/kernel/debug/tracing
 ># echo mlx5:mlx5e_tc_update_neigh_used_value >> set_event
 ># cat trace
    ...
    kworker/u48:4-8806  [009] ...1 55117.882428: mlx5e_tc_update_neigh_used_value:
netdev: ens1f0 IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_used=1

Added corresponding documentation in
    Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NDmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Implemented following tracepoints:
1. Configure flower (mlx5e_configure_flower)
2. Delete flower (mlx5e_delete_flower)
3. Stats flower (mlx5e_stats_flower)

Usage example:
 ># cd /sys/kernel/debug/tracing
 ># echo mlx5:mlx5e_configure_flower >> set_event
 ># cat trace
    ...
    tc-6535  [019] ...1  2672.404466: mlx5e_configure_flower: cookie=0000000067874a55 actions= REDIRECT

Added corresponding documentation in
    Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: NDmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: NVlad Buslov <vladbu@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To remove dependency on rtnl lock and prevent neigh update code from
accessing uninitialized flows when executing concurrently with tc, extend
mlx5e_tc_flow with 'init_done' completion. Modify helper
mlx5e_take_all_encap_flows() to wait for flow completion after obtaining
reference to it. Modify mlx5e_tc_encap_flows_del() and
mlx5e_tc_encap_flows_add() to skip flows that don't have OFFLOADED flag
set, which can happen if concurrent flow initialization failed.

This commit finishes neigh update refactoring for concurrent execution
started in previous change in this series.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to remove dependency on rtnl lock and allow neigh update workqueue
task to execute concurrently with tc, refactor mlx5e_rep_neigh_update() for
concurrent execution:

- Lock encap table when accessing encap entry to prevent concurrent
  changes. To do this properly, the initial encap state check is moved from
  mlx5e_rep_neigh_update() into mlx5e_rep_update_flows() to be performed
  under encap_tbl_lock protection.

- Wait for encap to be fully initialized before accessing it by means of
  'res_ready' completion.

- Add mlx5e_take_all_encap_flows() helper which is used to construct a
  temporary list of flows and efi indexes that is used to access current
  encap data in flow which can be attached to multiple encaps
  simultaneously. Release the flows from temporary list after
  encap_tbl_lock critical section. This is necessary because
  mlx5e_flow_put() can't be called while holding encap_tbl_lock.

- Modify mlx5e_tc_encap_flows_add() and mlx5e_tc_encap_flows_del() to work
  with user-provided list of flows built by mlx5e_take_all_encap_flows(),
  instead of traversing encap flow list directly.

This is first step in complex neigh update refactoring, which is finished
by following commit in this series.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to remove dependency on rtnl lock and allow neigh used value
update workqueue task to execute concurrently with tc, refactor
mlx5e_tc_update_neigh_used_value() for concurrent execution:

- Lock encap table when accessing encap entry to prevent concurrent
  changes.

- Save offloaded encap flows to temporary list and release them after encap
  entry is updated. Add mlx5e_put_encap_flow_list() helper which is
  intended to be shared with neigh update code in following patch in this
  series. This is necessary because mlx5e_flow_put() can't be called while
  holding encap_tbl_lock.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Rcu-ify mlx5e_neigh_hash_entry->encap_list by changing operations on encap
list to their rcu counterparts and extending encap structure with rcu_head
to free the encap instances after rcu grace period. Use rcu read lock when
traversing encap list. Implement helper mlx5e_get_next_valid_encap()
function that is used by mlx5e_tc_update_neigh_used_value() to safely
iterate over valid entries of nhe->encap_list.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To remove dependency on rtnl lock, always take neigh update encap lock when
modifying neigh update hash table and list. Originally, this lock was only
used to synchronize with netevent handler function, which is called from bh
context and cannot use rtnl lock for synchronization. Take lock in encap
entry attach function to prevent concurrent modifications of neigh update
hash table and list.

Taking the encap lock when creating new nhe introduces a problem that we
need to allocate new entry with sleeping GFP_KERNEL flag while holding a
spinlock. However, since previous patch in this series has already
converted lookup in netevent handler function to user rcu read lock instead
of encap lock, we can safely convert the lock type to mutex.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To remove dependency on rtnl lock and to allow unlocked iteration over list
of neigh hash entries, extend nhe with rcu. Change operations on neigh list
to their rcu counterparts and free neigh hash entry with rcu timeout.

Introduce mlx5e_get_next_nhe() helper that is used to iterate over rcu
neigh list with reference to nhe taken.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Neigh entry has reference counter, however it is only used when scheduling
neigh update event. In all other cases reference to neigh entry is not
taken while working with it. Neigh code relies on synchronization provided
by rtnl lock and uses encap list size as implicit reference counter.

To remove dependency on rtnl lock, always take reference to neigh entry
while using it. Remove neigh entry from hash table and delete it only when
reference counter reaches zero. This can result spurious neigh update
events, when there is an event on entry that has zero encaps attached.
However, such events are rare and properly handled by neigh update handler.

Extend encap entry with reference to neigh hash entry in order to be able
to directly release it when encap is detached, instead of lookup nhe by key
through hash table. Extend nhe with reference to device priv structure to
guarantee correctness when nhe is used with stack devices, bond setup, in
which case it is non-trivial to determine correct device when releasing the
nhe.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

As a preparation for following refactoring that removes rtnl lock
dependency from neigh hash entry handlers, extract code that enqueues neigh
update work into standalone function. This commit doesn't change
functionality.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>