There were some places that compared port_speed == -1 where port_speed
is a u8.  This doesn't work unless we cast the -1 to u8.  Some places
did it correctly.

Instead of using -1 directly, I've created a DUPLICATE_ENTRY define
which does the cast and is more descriptive as well.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.

This should be queued for kernels back to 2.6.31
Signed-off-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org

Isochronous and interrupt SuperSpeed endpoints use the same mechanisms
for decoding bInterval values as HighSpeed ones so adjust the code
accordingly.

Also bandwidth reservation for SuperSpeed matches highspeed, not
low/full speed.
Signed-off-by: NDmitry Torokhov <dtor@vmware.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the HcInterrupt register write to clear the
pending interrupt to after the isr work is done, doing this removes
glitches in the irq line.
Signed-off-by: NRichard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver did not take the zero flag in the USB request. If the
request length is the same as the endpoint's maxpacket, an additional
ZLP with no data has to be transmitted.

The method used here is inspired to what is done in fsl_udc_core.c
(and pxa27x_udc.c and at91_udc.c) where this is supported.

There already was a discussion about this topic with people from
Keymile, and I propose here a better implementation:

http://thread.gmane.org/gmane.linux.usb.general/38951Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are two -ENODEV error paths in qcprobe where the allocated private
data is not freed, this patch adds the two missing kfrees to avoid
leaking memory on the error path
Signed-off-by: NSteven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Rework the qcprobe logic such that serial->private is not set when
qcprobe exits with -ENODEV, otherwise serial->private will point to freed
memory on -ENODEV
Signed-off-by: NSteven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

qcprobe function allocates serial->private but this is never freed, this
patch adds a new function qc_release() which frees serial->private, after
calling usb_wwan_release
Signed-off-by: NSteven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb serial: ftdi_sio: add two missing USB ID's for Hameg interfaces HO720
and HO730

Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Bind only modem AT command endpoint to option.
Signed-off-by: NMarius B. Kotsbak <marius@kotsbak.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There was an unlock missing on the error path.

Also I did a small cleanup by changing ep->dev->lock for just dev->lock.
They're the same lock, but dev->lock is shorter and that's how it is
used for the spin_unlock_irqrestore() call.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Booting latest kernel on my test machine produces a lockdep
warning from the usb_amd_find_chipset_info() function:

 WARNING: at /data/lemmy/linux.trees.git/kernel/lockdep.c:2465 lockdep_trace_alloc+0x95/0xc2()
 Hardware name: Snook
 Modules linked in:
 Pid: 959, comm: work_for_cpu Not tainted 2.6.39-rc2+ #22
 Call Trace:
  [<ffffffff8103c0d4>] warn_slowpath_common+0x80/0x98
  [<ffffffff812387e6>] ? T.492+0x24/0x26
  [<ffffffff8103c101>] warn_slowpath_null+0x15/0x17
  [<ffffffff81068667>] lockdep_trace_alloc+0x95/0xc2
  [<ffffffff810ed9ac>] slab_pre_alloc_hook+0x18/0x3b
  [<ffffffff810ef227>] kmem_cache_alloc_trace+0x25/0xba
  [<ffffffff812387e6>] T.492+0x24/0x26
  [<ffffffff81238816>] pci_get_subsys+0x2e/0x73
  [<ffffffff8123886c>] pci_get_device+0x11/0x13
  [<ffffffff814082a9>] usb_amd_find_chipset_info+0x3f/0x18a
...

It turns out that this function calls pci_get_device under a spin_lock
with irqs disabled, but the pci_get_device function is only allowed in
preemptible context.

This patch fixes the warning by making all data-structure
modifications on temporal storage and commiting this back
into the visible structure at the end. While at it, this
patch also moves the pci_dev_put calls out of the spinlocks
because this function might sleep too.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We should free both descriptors.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In file included from drivers/usb/host/ohci-hcd.c:1028:0:
drivers/usb/host/ohci-au1xxx.c:36:7: warning: "__BIG_ENDIAN" is not defined
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add PID 0x0103 for serial port of the OCT DK201 docking station.
Reported-by: NJan Hoogenraad <jan@hoogenraad.net>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix build failure introduced by commit
7acc6197 (usb: musb: Idle path retention
and offmode support for OMAP3) when building without gadget
support.

  CC      drivers/usb/musb/omap2430.o
drivers/usb/musb/omap2430.c: In function ‘musb_otg_notifications’:
drivers/usb/musb/omap2430.c:262: error: ‘struct musb’ has no member named ‘gadget_driver’
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly.  This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.

The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-Tested-by: NDan Duval <dan.duval@stratus.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

During processing of bunch of eem frames if "echo" command is found
skb is cloned and the cloned version should be used to send reply.
Unfortunately, the data of the original skb were actually used and
the cloned skb is never freed.

Using the cloned skb and freeing the skb in the completion callback
for usb request.
Signed-off-by: NYauheni Kaliuta <yauheni.kaliuta@nokia.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I added new ProdutIds for two devices from CTI GmbH Leipzig.
Signed-off-by: NChristian Simon <simon@swine.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Because the disconnect function in the composite driver will call spin_lock,
this driver has to call spin_unlock before calling driver->disconnet().
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig

Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)
Signed-off-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ep_read() acquires data->lock mutex in get_ready_ep() and releases it on
all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix printk format build warning and grammar typo on same line.

drivers/usb/host/isp1760-hcd.c:300: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-greg' of git://gitorious.org/usb/usb:
  USB: musb: blackfin: work around anomaly 05000450
  usb: musb: Fix the crash issue during reboot
  usb: musb: gadget: check the correct list_head
  usb: musb: temporarily make it bool
  USB: musb: dereferencing an iomem pointer
  USB: musb: silence printk format warning
  USB: musb: using 0 instead of NULL
  USB: musb: add missing unlock in cppi_interrupt()
  usb: musb: ux500: copy dma mask from platform device to musb device
  usb: musb: clear AUTOSET while clearing DMAENAB

DMA mode 1 data corruption anomaly on Blackfin systems.  This issue is
specific to the Blackfin silicon as the bug appears to be related to the
connection of the musb ip to the bus/dma fabric.

Data corruption when using USB DMA mode 1. (Issue manager 17-01-0105)
DMA mode 1 allows large size transfers to generate a single interrupt
at the end of the entire transfer.  The transfer is split up in packets
of length specified in the Maximum Packet Size field for that endpoint.
If the transfer size is not an integer multiple of the Maximum Packet
Size, a short packet will be present at the end of the transfer.

Under certain conditions this packet may be corrupted in the USB FIFO.

Workaround:
Use DMA mode 1 to transfer (n* Maximum Packet Size) and schedule DMA
mode 0 to transfer the short packet.

As an example if your transfer size is 33168 bytes and Maximum Packet
Size equals 512, schedule [33168 - (33168 mod 512)] in DMA mode 1 and
the remainder (33168 mod 512) in DMA mode 0.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Below crash observed with commit 7acc6197
(usb: musb: Idle path retention and offmode support for OMAP3)
during board reboot.

The musb clock was disabled when musb_shutdown() was called by
platform_drv_shutdown in which there are register accesses.
call pm_runtime_get_sync() and pm_runtime_put_sync() in the
musb_shutdown function.

/ # [  172.368774] Unhandled fault: imprecise external abort (0x1406) at 0x400f0000
[  172.376190] Internal error: : 1406 [#1] SMP
[  172.380554] last sysfs file: /sys/devices/platform/omap/omap_i2c.4/i2c-4/i2c-dev/i2c-4/dev
[  172.389221] Modules linked in:
[  172.392456] CPU: 0    Tainted: G        W    (2.6.38-06671-geddecbb6 #33)
[  172.399475] PC is at do_raw_spin_unlock+0x50/0xc0
[  172.404418] LR is at _raw_spin_unlock_irqrestore+0x24/0x44
[  172.410186] pc : [<c069bfdc>]    lr : [<c085a7f8>]    psr: 60000093
[  172.410186] sp : ee993e40  ip : c0d00240  fp : bea9cf14
[  172.422241] r10: 00000000  r9 : ee992000  r8 : c04b2fa8
[  172.427703] r7 : 00000000  r6 : c0fa46c0  r5 : ef966124  r4 : ef966124
[  172.434539] r3 : ef92cbc0  r2 : ef92cbc0  r1 : 00000000  r0 : ef966124
[  172.441406] Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[  172.448974] Control: 10c5387d  Table: ae8d804a  DAC: 00000015
[  172.454986] Process init (pid: 1094, stack limit = 0xee9922f8)
[  172.461120] Stack: (0xee993e40 to 0xee994000)
[  172.465667] 3e40: a0000013 c085a7f8 ef966124 a0000013 c0fa46c0 c0761ab4 c0761a70 ef95c008
[  172.474273] 3e60: ef95c014 c06e2fd0 c06e2fbc c06dea90 00000000 01234567 28121969 c04fccb4
[  172.482849] 3e80: 00000000 c04fcd04 c0a302bc c04fce44 c0a02600 00000001 00000000 c085cd04
[  172.491424] 3ea0: 00000000 00000002 c09ea000 c085afc0 ee993f24 00000000 00040001 00000445
[  172.499999] 3ec0: a8eb9d34 00000027 00000000 00000000 00000000 c0a56a4c 00000000 00000000
[  172.508575] 3ee0: 00000002 60000093 00000000 c0519aac 00000002 00000080 00000000 c0550420
[  172.517150] 3f00: 00000000 00000002 ee970000 c0a56a3c c0a56a20 00000002 c0a56a3c 00000000
[  172.525726] 3f20: c0a56a3c 0000000a c1580e00 c0a56a20 00000002 c0a56a3c c1580e00 c0a56a20
[  172.534301] 3f40: ef92cbc0 c05173a0 00000001 ef92cbc0 c0576190 c04e3174 20000013 c0517324
[  172.542877] 3f60: ef815c00 ee90b720 c04e3174 c0576190 00000001 ef92cbc0 c04b2f00 ffffffff
[  172.551483] 3f80: 00000058 c0517324 00000000 00000000 ffffffff 00000000 00000000 ffffffff
[  172.560058] 3fa0: 00000058 c04b2de0 00000000 00000000 fee1dead 28121969 01234567 00000000
[  172.568634] 3fc0: 00000000 00000000 ffffffff 00000058 00000000 00000001 400aa000 bea9cf14
[  172.577209] 3fe0: 000ea148 bea9c958 000aa750 40225728 60000010 fee1dead 00000000 00000000
[  172.585784] [<c069bfdc>] (do_raw_spin_unlock+0x50/0xc0) from [<c085a7f8>] (_raw_spin_unlock_irqrestore+0x24/0x44)
[  172.596588] [<c085a7f8>] (_raw_spin_unlock_irqrestore+0x24/0x44) from [<c0761ab4>] (musb_shutdown+0x44/0x88)
[  172.606933] [<c0761ab4>] (musb_shutdown+0x44/0x88) from [<c06e2fd0>] (platform_drv_shutdown+0x14/0x18)
[  172.616699] [<c06e2fd0>] (platform_drv_shutdown+0x14/0x18) from [<c06dea90>] (device_shutdown+0x74/0xb4)
[  172.626647] [<c06dea90>] (device_shutdown+0x74/0xb4) from [<c04fccb4>] (kernel_restart_prepare+0x24/0x38)
[  172.636688] [<c04fccb4>] (kernel_restart_prepare+0x24/0x38) from [<c04fcd04>] (kernel_restart+0xc/0x48)
[  172.646545] [<c04fcd04>] (kernel_restart+0xc/0x48) from [<c04fce44>] (sys_reboot+0xfc/0x1d8)
[  172.655426] [<c04fce44>] (sys_reboot+0xfc/0x1d8) from [<c04b2de0>] (ret_fast_syscall+0x0/0x3c)
[  172.664459] Code: e3c3303f e594200c e593300c e1520003 (0a000002)
[  172.670867] ------------[ cut here ]------------
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We are now using our own list_head, so we should
be checking against that, not the gadget driver's
list_head.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.

Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.

Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.

Cc: stable@kernel.org # v2.6.38
Signed-off-by: NFelipe Balbi <balbi@ti.com>

"tx_ram" points to io memory.  We can't dereference it directly.  Sparse
complains about this: "drivers/usb/musb/cppi_dma.c:1205:25: warning:
dereference of noderef expression"
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Gcc gives the following warnings:

drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_tx_segment’:
drivers/usb/musb/cppi_dma.c:600: warning: format ‘%x’ expects type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_rx_segment’:
drivers/usb/musb/cppi_dma.c:822: warning: format ‘%x’ expects type ‘unsigned int’, but argument 9 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_rx_scan’:
drivers/usb/musb/cppi_dma.c:1042: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c:1114: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 7 has type ‘dma_addr_t’

dma_addr_t is sometimes 32 bit and sometimes 64.  We normally cast them
to unsigned long long for printk().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Sparse complains (and rightly so):
drivers/usb/musb/cppi_dma.c:1458:33:
	warning: Using plain integer as NULL pointer
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We should unlock before returning here.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

musb code checks dma mask before calling dma hooks.
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: use proper interfaces for on-stack plugging
  xfs: fix xfs_debug warnings
  xfs: fix variable set but not used warnings
  xfs: convert log tail checking to a warning
  xfs: catch bad block numbers freeing extents.
  xfs: push the AIL from memory reclaim and periodic sync
  xfs: clean up code layout in xfs_trans_ail.c
  xfs: convert the xfsaild threads to a workqueue
  xfs: introduce background inode reclaim work
  xfs: convert ENOSPC inode flushing to use new syncd workqueue
  xfs: introduce a xfssyncd workqueue
  xfs: fix extent format buffer allocation size
  xfs: fix unreferenced var error in xfs_buf.c

Also, applied patch from Tony Luck that fixes ia64:
  xfs_destroy_workqueues() should not be tagged with__exit
in the branch before merging.

ia64 throws away .exit sections for the built-in CONFIG case, so routines
that are used in other circumstances should not be tagged as __exit.
Signed-off-by: NTony Luck <tony.luck@intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAlex Elder <aelder@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix data corruption regression by reverting commit 6de9843d
  ext4: Allow indirect-block file to grow the file size to max file size
  ext4: allow an active handle to be started when freezing
  ext4: sync the directory inode in ext4_sync_parent()
  ext4: init timer earlier to avoid a kernel panic in __save_error_info
  jbd2: fix potential memory leak on transaction commit
  ext4: fix a double free in ext4_register_li_request
  ext4: fix credits computing for indirect mapped files
  ext4: remove unnecessary [cm]time update of quota file
  jbd2: move bdget out of critical section

* 'for-2.6.39' of git://linux-nfs.org/~bfields/linux:
  nfsd4: fix oops on lock failure
  nfsd: fix auth_domain reference leak on nlm operations

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  dt/fsldma: fix build warning caused by of_platform_device changes
  spi: Fix race condition in stop_queue()
  gpio/pch_gpio: Fix output value of pch_gpio_direction_output()
  gpio/ml_ioh_gpio: Fix output value of ioh_gpio_direction_output()
  gpio/pca953x: fix error handling path in probe() call