Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 07 3月, 2019 1 次提交
  3. 02 3月, 2019 2 次提交
  5. 28 2月, 2019 1 次提交
  7. 09 2月, 2019 1 次提交
    • L
      net: ipv4: use a dedicated counter for icmp_v4 redirect packets · c09551c6
      由 Lorenzo Bianconi 提交于 
      According to the algorithm described in the comment block at the
beginning of ip_rt_send_redirect, the host should try to send
'ip_rt_redirect_number' ICMP redirect packets with an exponential
backoff and then stop sending them at all assuming that the destination
ignores redirects.
If the device has previously sent some ICMP error packets that are
rate-limited (e.g TTL expired) and continues to receive traffic,
the redirect packets will never be transmitted. This happens since
peer->rate_tokens will be typically greater than 'ip_rt_redirect_number'
and so it will never be reset even if the redirect silence timeout
(ip_rt_redirect_silence) has elapsed without receiving any packet
requiring redirects.

Fix it by using a dedicated counter for the number of ICMP redirect
packets that has been sent by the host

I have not been able to identify a given commit that introduced the
issue since ip_rt_send_redirect implements the same rate-limiting
algorithm from commit 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c09551c6
  9. 04 2月, 2019 1 次提交
  11. 20 1月, 2019 1 次提交
  13. 21 12月, 2018 1 次提交
    • I
      net: ipv4: Set skb->dev for output route resolution · 21f94775
      由 Ido Schimmel 提交于 
      When user requests to resolve an output route, the kernel synthesizes
an skb where the relevant parameters (e.g., source address) are set. The
skb is then passed to ip_route_output_key_hash_rcu() which might call
into the flow dissector in case a multipath route was hit and a nexthop
needs to be selected based on the multipath hash.

Since both 'skb->dev' and 'skb->sk' are not set, a warning is triggered
in the flow dissector [1]. The warning is there to prevent codepaths
from silently falling back to the standard flow dissector instead of the
BPF one.

Therefore, instead of removing the warning, set 'skb->dev' to the
loopback device, as its not used for anything but resolving the correct
namespace.

[1]
WARNING: CPU: 1 PID: 24819 at net/core/flow_dissector.c:764 __skb_flow_dissect+0x314/0x16b0
...
RSP: 0018:ffffa0df41fdf650 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8bcded232000 RCX: 0000000000000000
RDX: ffffa0df41fdf7e0 RSI: ffffffff98e415a0 RDI: ffff8bcded232000
RBP: ffffa0df41fdf760 R08: 0000000000000000 R09: 0000000000000000
R10: ffffa0df41fdf7e8 R11: ffff8bcdf27a3000 R12: ffffffff98e415a0
R13: ffffa0df41fdf7e0 R14: ffffffff98dd2980 R15: ffffa0df41fdf7e0
FS:  00007f46f6897680(0000) GS:ffff8bcdf7a80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055933e95f9a0 CR3: 000000021e636000 CR4: 00000000001006e0
Call Trace:
 fib_multipath_hash+0x28c/0x2d0
 ? fib_multipath_hash+0x28c/0x2d0
 fib_select_path+0x241/0x32f
 ? __fib_lookup+0x6a/0xb0
 ip_route_output_key_hash_rcu+0x650/0xa30
 ? __alloc_skb+0x9b/0x1d0
 inet_rtm_getroute+0x3f7/0xb80
 ? __alloc_pages_nodemask+0x11c/0x2c0
 rtnetlink_rcv_msg+0x1d9/0x2f0
 ? rtnl_calcit.isra.24+0x120/0x120
 netlink_rcv_skb+0x54/0x130
 rtnetlink_rcv+0x15/0x20
 netlink_unicast+0x20a/0x2c0
 netlink_sendmsg+0x2d1/0x3d0
 sock_sendmsg+0x39/0x50
 ___sys_sendmsg+0x2a0/0x2f0
 ? filemap_map_pages+0x16b/0x360
 ? __handle_mm_fault+0x108e/0x13d0
 __sys_sendmsg+0x63/0xa0
 ? __sys_sendmsg+0x63/0xa0
 __x64_sys_sendmsg+0x1f/0x30
 do_syscall_64+0x5a/0x120
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: d0e13a14 ("flow_dissector: lookup netns by skb->sk if skb->dev is NULL")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      21f94775
  15. 21 11月, 2018 1 次提交
  17. 11 10月, 2018 1 次提交
    • S
      net: ipv4: don't let PMTU updates increase route MTU · 28d35bcd
      由 Sabrina Dubroca 提交于 
      When an MTU update with PMTU smaller than net.ipv4.route.min_pmtu is
received, we must clamp its value. However, we can receive a PMTU
exception with PMTU < old_mtu < ip_rt_min_pmtu, which would lead to an
increase in PMTU.

To fix this, take the smallest of the old MTU and ip_rt_min_pmtu.

Before this patch, in case of an update, the exception's MTU would
always change. Now, an exception can have only its lock flag updated,
but not the MTU, so we need to add a check on locking to the following
"is this exception getting updated, or close to expiring?" test.

Fixes: d52e5a7e ("ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      28d35bcd
  19. 05 10月, 2018 2 次提交
  21. 03 10月, 2018 2 次提交
  23. 27 9月, 2018 2 次提交
  25. 30 7月, 2018 1 次提交
    • X
      route: add support for directed broadcast forwarding · 5cbf777c
      由 Xin Long 提交于 
      This patch implements the feature described in rfc1812#section-5.3.5.2
and rfc2644. It allows the router to forward directed broadcast when
sysctl bc_forwarding is enabled.

Note that this feature could be done by iptables -j TEE, but it would
cause some problems:
  - target TEE's gateway param has to be set with a specific address,
    and it's not flexible especially when the route wants forward all
    directed broadcasts.
  - this duplicates the directed broadcasts so this may cause side
    effects to applications.

Besides, to keep consistent with other os router like BSD, it's also
necessary to implement it in the route rx path.

Note that route cache needs to be flushed when bc_forwarding is
changed.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5cbf777c
  27. 13 6月, 2018 2 次提交
    • K
      treewide: kzalloc() -> kcalloc() · 6396bb22
      由 Kees Cook 提交于 
      The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:

        kzalloc(a * b, gfp)

with:
        kcalloc(a * b, gfp)

as well as handling cases of:

        kzalloc(a * b * c, gfp)

with:

        kzalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kzalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kzalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kzalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kzalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kzalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kzalloc
+ kcalloc
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kzalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kzalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kzalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kzalloc(sizeof(THING) * C2, ...)
|
  kzalloc(sizeof(TYPE) * C2, ...)
|
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	E1 * E2
+	E1, E2
  , ...)
)
Signed-off-by: NKees Cook <keescook@chromium.org>
      6396bb22
    • K
      treewide: kmalloc() -> kmalloc_array() · 6da2ec56
      由 Kees Cook 提交于 
      The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:

        kmalloc(a * b, gfp)

with:
        kmalloc_array(a * b, gfp)

as well as handling cases of:

        kmalloc(a * b * c, gfp)

with:

        kmalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kmalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kmalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kmalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kmalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kmalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kmalloc
+ kmalloc_array
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kmalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kmalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kmalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kmalloc(sizeof(THING) * C2, ...)
|
  kmalloc(sizeof(TYPE) * C2, ...)
|
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	E1 * E2
+	E1, E2
  , ...)
)
Signed-off-by: NKees Cook <keescook@chromium.org>
      6da2ec56
  29. 24 5月, 2018 1 次提交
  31. 22 5月, 2018 1 次提交
  33. 18 5月, 2018 1 次提交
  35. 16 5月, 2018 1 次提交
  37. 11 5月, 2018 1 次提交
    • H
      ipv4: reset fnhe_mtu_locked after cache route flushed · 0e8411e4
      由 Hangbin Liu 提交于 
      After route cache is flushed via ipv4_sysctl_rtcache_flush(), we forget
to reset fnhe_mtu_locked in rt_bind_exception(). When pmtu is updated
in __ip_rt_update_pmtu(), it will return directly since the pmtu is
still locked. e.g.

+ ip netns exec client ping 10.10.1.1 -c 1 -s 1400 -M do
PING 10.10.1.1 (10.10.1.1) 1400(1428) bytes of data.
>From 10.10.0.254 icmp_seq=1 Frag needed and DF set (mtu = 0)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0e8411e4
  39. 03 5月, 2018 1 次提交
    • J
      ipv4: fix fnhe usage by non-cached routes · 94720e3a
      由 Julian Anastasov 提交于 
      Allow some non-cached routes to use non-expired fnhe:

1. ip_del_fnhe: moved above and now called by find_exception.
The 4.5+ commit deed49df expires fnhe only when caching
routes. Change that to:

1.1. use fnhe for non-cached local output routes, with the help
from (2)

1.2. allow __mkroute_input to detect expired fnhe (outdated
fnhe_gw, for example) when do_cache is false, eg. when itag!=0
for unicast destinations.

2. __mkroute_output: keep fi to allow local routes with orig_oif != 0
to use fnhe info even when the new route will not be cached into fnhe.
After commit 839da4d9 ("net: ipv4: set orig_oif based on fib
result for local traffic") it means all local routes will be affected
because they are not cached. This change is used to solve a PMTU
problem with IPVS (and probably Netfilter DNAT) setups that redirect
local clients from target local IP (local route to Virtual IP)
to new remote IP target, eg. IPVS TUN real server. Loopback has
64K MTU and we need to create fnhe on the local route that will
keep the reduced PMTU for the Virtual IP. Without this change
fnhe_pmtu is updated from ICMP but never exposed to non-cached
local routes. This includes routes with flowi4_oif!=0 for 4.6+ and
with flowi4_oif=any for 4.14+).

3. update_or_create_fnhe: make sure fnhe_expires is not 0 for
new entries

Fixes: 839da4d9 ("net: ipv4: set orig_oif based on fib result for local traffic")
Fixes: d6d5e999 ("route: do not cache fib route info on local routes with oif")
Fixes: deed49df ("route: check and remove route cache when we get route")
Cc: David Ahern <dsahern@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      94720e3a
  41. 08 4月, 2018 1 次提交
    • E
      ipv4: fix uninit-value in ip_route_output_key_hash_rcu() · d0ea2b12
      由 Eric Dumazet 提交于 
      syzbot complained that res.type could be used while not initialized.

Using RTN_UNSPEC as initial value seems better than using garbage.

BUG: KMSAN: uninit-value in __mkroute_output net/ipv4/route.c:2200 [inline]
BUG: KMSAN: uninit-value in ip_route_output_key_hash_rcu+0x31f0/0x3940 net/ipv4/route.c:2493
CPU: 1 PID: 12207 Comm: syz-executor0 Not tainted 4.16.0+ #81
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x185/0x1d0 lib/dump_stack.c:53
 kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:676
 __mkroute_output net/ipv4/route.c:2200 [inline]
 ip_route_output_key_hash_rcu+0x31f0/0x3940 net/ipv4/route.c:2493
 ip_route_output_key_hash net/ipv4/route.c:2322 [inline]
 __ip_route_output_key include/net/route.h:126 [inline]
 ip_route_output_flow+0x1eb/0x3c0 net/ipv4/route.c:2577
 raw_sendmsg+0x1861/0x3ed0 net/ipv4/raw.c:653
 inet_sendmsg+0x48d/0x740 net/ipv4/af_inet.c:764
 sock_sendmsg_nosec net/socket.c:630 [inline]
 sock_sendmsg net/socket.c:640 [inline]
 SYSC_sendto+0x6c3/0x7e0 net/socket.c:1747
 SyS_sendto+0x8a/0xb0 net/socket.c:1715
 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x455259
RSP: 002b:00007fdc0625dc68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fdc0625e6d4 RCX: 0000000000455259
RDX: 0000000000000000 RSI: 0000000020000040 RDI: 0000000000000013
RBP: 000000000072bea0 R08: 0000000020000080 R09: 0000000000000010
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000000004f7 R14: 00000000006fa7c8 R15: 0000000000000000

Local variable description: ----res.i.i@ip_route_output_flow
Variable was created at:
 ip_route_output_flow+0x75/0x3c0 net/ipv4/route.c:2576
 raw_sendmsg+0x1861/0x3ed0 net/ipv4/raw.c:653
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d0ea2b12
  43. 06 4月, 2018 1 次提交
    • R
      headers: untangle kmemleak.h from mm.h · 514c6032
      由 Randy Dunlap 提交于 
      Currently <linux/slab.h> #includes <linux/kmemleak.h> for no obvious
reason.  It looks like it's only a convenience, so remove kmemleak.h
from slab.h and add <linux/kmemleak.h> to any users of kmemleak_* that
don't already #include it.  Also remove <linux/kmemleak.h> from source
files that do not use it.

This is tested on i386 allmodconfig and x86_64 allmodconfig.  It would
be good to run it through the 0day bot for other $ARCHes.  I have
neither the horsepower nor the storage space for the other $ARCHes.

Update: This patch has been extensively build-tested by both the 0day
bot & kisskb/ozlabs build farms.  Both of them reported 2 build failures
for which patches are included here (in v2).

[ slab.h is the second most used header file after module.h; kernel.h is
  right there with slab.h. There could be some minor error in the
  counting due to some #includes having comments after them and I didn't
  combine all of those. ]

[akpm@linux-foundation.org: security/keys/big_key.c needs vmalloc.h, per sfr]
Link: http://lkml.kernel.org/r/e4309f98-3749-93e1-4bb7-d9501a39d015@infradead.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Reviewed-by: NIngo Molnar <mingo@kernel.org>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>	[2 build failures]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>	[2 build failures]
Reviewed-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      514c6032
  45. 28 3月, 2018 1 次提交
  47. 27 3月, 2018 1 次提交
  49. 15 3月, 2018 1 次提交
    • S
      ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu · d52e5a7e
      由 Sabrina Dubroca 提交于 
      Prior to the rework of PMTU information storage in commit
2c8cec5c ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.

Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.

This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().

One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.

Fixes: 2c8cec5c ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d52e5a7e
  51. 05 3月, 2018 3 次提交
  53. 02 3月, 2018 2 次提交
  55. 01 3月, 2018 1 次提交
  57. 28 2月, 2018 1 次提交
  59. 23 2月, 2018 1 次提交
  61. 16 2月, 2018 2 次提交
    • X
      xfrm: reuse uncached_list to track xdsts · 510c321b
      由 Xin Long 提交于 
      In early time, when freeing a xdst, it would be inserted into
dst_garbage.list first. Then if it's refcnt was still held
somewhere, later it would be put into dst_busy_list in
dst_gc_task().

When one dev was being unregistered, the dev of these dsts in
dst_busy_list would be set with loopback_dev and put this dev.
So that this dev's removal wouldn't get blocked, and avoid the
kmsg warning:

  kernel:unregister_netdevice: waiting for veth0 to become \
  free. Usage count = 2

However after Commit 52df157f ("xfrm: take refcnt of dst
when creating struct xfrm_dst bundle"), the xdst will not be
freed with dst gc, and this warning happens.

To fix it, we need to find these xdsts that are still held by
others when removing the dev, and free xdst's dev and set it
with loopback_dev.

But unfortunately after flow_cache for xfrm was deleted, no
list tracks them anymore. So we need to save these xdsts
somewhere to release the xdst's dev later.

To make this easier, this patch is to reuse uncached_list to
track xdsts, so that the dev refcnt can be released in the
event NETDEV_UNREGISTER process of fib_netdev_notifier.

Thanks to Florian, we could move forward this fix quickly.

Fixes: 52df157f ("xfrm: take refcnt of dst when creating struct xfrm_dst bundle")
Reported-by: NJianlin Shi <jishi@redhat.com>
Reported-by: NHangbin Liu <liuhangbin@gmail.com>
Tested-by: NEyal Birger <eyal.birger@gmail.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
      510c321b
    • D
      net/ipv4: Remove fib table id from rtable · 68e813aa
      由 David Ahern 提交于 
      Remove rt_table_id from rtable. It was added for getroute to return the
table id that was hit in the lookup. With the changes for fibmatch the
table id can be extracted from the fib_info returned in the fib_result
so it no longer needs to be in rtable directly.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      68e813aa