Driver rtl8192ce does not initialize the LED correctly.
Signed-off-by: NChaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element

Both spurChans arrays in modalHeader5G and modalHeader2G have 5 elements,
AR_EEPROM_MODAL_SPURS is defined 5. So unless a break occurs, in the
last iteration (i=5) we tried to access spurChansPtr[5] before testing
whether i was within bounds. Fix this.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While the rx/tx tasklet is pending, new unnecessary interrupts may arrive.
Decrease the load by temporarily disabling the interrupts until the tasklet
has completed.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The pointers to the debugfs entries do not need to be saved, because they
will be recursively removed when the wiphy is unregistered.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reusing the configured retry counts from the skb cb is more efficient than
reloading the data from uncached memory.
Replace ts_longretry (unused) with ts_final_retry which contains the retry
count for the final rate only
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use ACCESS_ONCE to reduce the number of redundant loads on uncached memory
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use ACCESS_ONCE to reduce the number of variable reloads on uncached memory
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is no longer necessary for preparing mac80211 tx status
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use local variables to reduce the number of load/store operations on uncached
memory.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the slot time based on the mac80211 short slot vs long slot setting
instead of just forcing long slot for all CCK-enabled channels.
This slightly improves 802.11g mode performance in in my tests.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k uses 8 usec as a sifs time, extracted from the initvals, whereas the
standard requires a sifs time of 10. The difference originates from the fact
that the SIFS register has an offset of 2 usec.
Fix the SIFS time definition to use the standard value of 10 usec and subtract
2 usecs when writing the SIFS register.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Subtract the difference in preamble duration (in usec) from the value
returned by ieee80211_generic_frame_duration.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During normal operation, minstrel was showing suspicious EWMA probabilities
exceeding 100%. It looks like the tx status reporting in ath5k was not
properly clearing the rate index for rates which were never attempted.

This is caused by uninitialized stale data in the on-stack tx status
information, which is reused when more frames are received.

To fix this, rely on ts->ts_final_idx to select the last attempted rate,
instead of checking whether ts->ts_rate is set.

Additionally, the conversion from the driver rate index back to the
mac80211 rate index can be dropped, as the mac80211 tx status will still
have the original rate index which was used to set up the descriptor.

Additionally, one more inaccuracy was fixed - the final rate attempt
count only needs to be increased by one if the transmission attempt was
successful.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath5k driver does kmalloc allocations for pcal info in a loop.
But, if one fails it was simply returning -ENOMEM without freeing
already allocated memory.  This patch corrects that oversight.
Reported-by: NEugene A. Shatokhin <dame_eugene@mail.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reviewed-by: NBob Copeland <me@bobcopeland.com>

Fix checkpatch errors and warnings comprising of indent errors, spaces and
__packed warnings. Also fix 'make C = 2' warnings.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add station connected time in debugfs. This will be helpful to get a
measure of stability of the connection and for debugging stress issues

Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update Tx gain 23 for all tx gain table.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Export RSSI information from all the control and extension
channel chains to debugfs. Also add rx antenna information
to debugfs. This will be useful for debugging purpose.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also, advertise support for mesh authentication.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Notify userspace when a beacon/presp is received from a suitable mesh
peer candidate for whom no sta information exists.  Userspace can then
decide to create a sta info for the candidate.  If userspace is not
ready to authenticate the peer right away, it can create the sta info
with the authenticated flag unset and set it later.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Modify the NEW_STATION command to accept PLINK_ACTIONS, in case
userspace wants to create stations and initiate a peer link right away
(for authenticated stations) or create a blocked station (for
debugging).
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During mesh setup, use NL80211_MESH_SETUP_USERSPACE_AUTH flag to create
a secure mesh and route management frames to userspace.

Also, NL80211_CMD_GET_WIPHY now returns a flag NL80211_SUPPORT_MESH_AUTH
if the wiphy's mesh implementation supports routing of mesh auth frames
to userspace.  This is useful for forward compatibility between old
kernels and new userspace tools.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To NL80211_MESH_SETUP_IE. This reflects our ability to insert any ie
into a mesh beacon, not simply path selection ies.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl4965_rate_control_register() prints a message at KERN_ERR level. It
looks like it's just a debugging message, so pr_err() seems to be
overdone. But none of the similar functions in drivers/net/wireless
print a message, so let's just drop it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of having separate key information definitions for
each type of key, a common key information bitmap is used.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before calling host_to_card() to send the cmd to firmware,
we use skb_push() to add 4 bytes SDIO interface header at
the start of the data buffer. Since cmd_skb data structure
will be re-used at a later time, we need to restore its
headroom by removing the 4 bytes header.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.

The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.

The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function returns true if there is atleast one frame
in any one of the tx queues.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a highly noisy environment, the tx rate of the driver drops and
the application slows down since it has not yet received ACKs for
the frames already queued in the hardware. Since this ACK may take
more than 100ms, stopping the dev queues for entering PS at this
stage breaks applications, WMM test cases in my testing.
If there are frames already pending in the tx queue, postponing the
PS logic helps to avoid redundant queue stops. When power save is
enabled by default and in a noisy environment, this API certainly
helps in improving the average throughput.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we maintain API properly, then there isn't
really a reason to warn about this since we'll
just be adding things that are safe to ignore,
so downgrade the warning to debug info level.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There's no need to keep both normal and BT statistics
versions around all the time in memory when we only
use a subset of both. So keep only the subsets that
we need in memory, depending on the debug config).

Also, in doing so, we can remove all the calls to
iwl_bt_statistics() in the driver as we'll just
access the copied statistics now.

Finally, also remove this call from the one place
where it might still be needed and automatically
detect what kind of statistics the device is sending
based on their size. This way, we don't need to keep
track of which devices do what any more, which is
good since this is subject to change based on the
ucode version (as some ucode even for non-BT devices
will in fact use BT statistics).

Warn upon encountering a statistics command from the
ucode that isn't known, so we will find such issues
earlier in the future.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>