As described in AHCI v1.0 specification chapter 10.6.2.2
"Multiple MSI Based Messages" generation of interrupts
is not controlled through the HOST_IRQ_STAT register.

Considering MMIO access is expensive remove unnecessary
reading and writing of HOST_IRQ_STAT register.

Further, serializing access to the host data is no longer
needed and the interrupt service routine can avoid competing
on the host lock.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Suggested-by: N"Jiang, Dave" <dave.jiang@intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: "Jiang, Dave" <dave.jiang@intel.com>
Cc: linux-ide@vger.kernel.org

Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org

Currently host activation done by calling either function
ahci_host_activate() or ata_host_activate(). Consolidate
the code by only calling ahci_host_activate() for all AHCI
devices.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org

This update is a prerequisite for consolidation of
AHCI host activation code within ahci_host_activate()
function.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org

This update is a prerequisite for consolidation of
AHCI host activation code within ahci_host_activate()
function.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org

Using the SIMPLE_DEV_PM_OPS() macro can make the code shorter and cleaner.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Sharing Last Message (SLM) mode is currently checked in two
functions: ahci_host_activate() and ahci_init_interrupts().
This update consolidates SLM mode check with activation of
multiple MSIs mode.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org

Currently, ata_sff_softreset is skipped for controllers with no ctl port.
But that also skips ata_sff_dev_classify required for device detection.
This means that libata is currently broken on controllers with no ctl port.

No device connected:
[    1.872480] pata_isapnp 01:01.02: activated
[    1.889823] scsi2 : pata_isapnp
[    1.890109] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    6.888110] ata3.01: qc timeout (cmd 0xec)
[    6.888179] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   16.888085] ata3.01: qc timeout (cmd 0xec)
[   16.888147] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.888086] ata3.01: qc timeout (cmd 0xec)
[   46.888148] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   51.888100] ata3.00: qc timeout (cmd 0xec)
[   51.888160] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[   61.888079] ata3.00: qc timeout (cmd 0xec)
[   61.888141] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
[   91.888089] ata3.00: qc timeout (cmd 0xec)
[   91.888152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)

ATAPI device connected:
[    1.882061] pata_isapnp 01:01.02: activated
[    1.893430] scsi2 : pata_isapnp
[    1.893719] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    6.892107] ata3.01: qc timeout (cmd 0xec)
[    6.892171] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   16.892079] ata3.01: qc timeout (cmd 0xec)
[   16.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.892079] ata3.01: qc timeout (cmd 0xec)
[   46.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5)
[   46.908586] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr
[   46.924570] ata3.00: configured for PIO0 (device error ignored)
[   46.926295] scsi 2:0:0:0: CD-ROM            ACER     CD-767E/O        1.5X PQ: 0 ANSI: 5
[   46.984519] sr0: scsi3-mmc drive: 6x/6x xa/form2 tray
[   46.984592] cdrom: Uniform CD-ROM driver Revision: 3.20

So don't skip ata_sff_softreset, just skip the reset part of ata_bus_softreset
if the ctl port is not available.

This makes IDE port on ES968 behave correctly:

No device connected:
[    4.670888] pata_isapnp 01:01.02: activated
[    4.673207] scsi host2: pata_isapnp
[    4.673675] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    7.081840] Adding 2541652k swap on /dev/sda2.  Priority:-1 extents:1 across:2541652k

ATAPI device connected:
[    4.704362] pata_isapnp 01:01.02: activated
[    4.706620] scsi host2: pata_isapnp
[    4.706877] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11
[    4.872782] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr
[    4.888673] ata3.00: configured for PIO0 (device error ignored)
[    4.893984] scsi 2:0:0:0: CD-ROM            ACER     CD-767E/O        1.5X PQ: 0 ANSI: 5
[    7.015578] Adding 2541652k swap on /dev/sda2.  Priority:-1 extents:1 across:2541652k
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

ahci_xgene: Fix the error print invalid resource for APM X-Gene SoC AHCI SATA Host Controller driver.

This patch fixes the error print invalid resource for the APM X-Gene
SoC AHCI SATA Host Controller driver. This print was due to the fact
that the controller 3 don't have a mux resource. This didn't result
in any errors but the print seems like meaningless.
Signed-off-by: NLoc Ho <lho@apm.com>
Signed-off-by: NSuman Tripathi <stripathi@apm.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The return value is not used by callers of these functions nor
by uses of all macros so change the functions to return void.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Qualcomm IPQ806x SoCs with SATA controllers need 5 clocks to be enabled.
Signed-off-by: NKumar Gala <galak@codeaurora.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The DMI table does not need to be written to, make it r/o.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

ahci_platform_enable_phys() and ahci_platform_disable_phys() are currently
exported, but they are not used anywhere else other than libahci_platform.c.

So make them static and do not export them to fix the following sparse
warnings:

drivers/ata/libahci_platform.c:52:5: warning: symbol 'ahci_platform_enable_phys' was not declared. Should it be static?
drivers/ata/libahci_platform.c:88:6: warning: symbol 'ahci_platform_disable_phys' was not declared. Should it be static?
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

IRQ flags can be obtained from resource structure, there are no need
to use additional field in the platform_data to store these values.
This patch removes this field and convert existing users of this driver
to use IRQ flags from the resources.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NTejun Heo <tj@kernel.org>

"electra-ide" is not used anywhere in the kernel and could be
represented in devicetree in a normal way.
This patch removes specific quirk for "electra-ide".
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NTejun Heo <tj@kernel.org>

Use dev_name() instead of driver name for request_irq().
This will help to distinguish between multiple identical devices.

Before:
 CPU0
 5:      34425  clps711x-intc   5  pata_of_platform
 6:       6778  clps711x-intc   6  pata_of_platform

After:
 CPU0
 5:       2182  clps711x-intc   5  20000000.ide
 6:      11024  clps711x-intc   6  20100000.ide
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NTejun Heo <tj@kernel.org>

The last user of the deprecated struct ahci_platform_data has been
cleaned up recently (SPEAr1340 got a proper PHY driver).
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The function may be useful for other drivers, so export it.  (Suggested
by Tejun Heo.)

Note that I inverted the return value of glob_match; returning true on
match seemed to make more sense.
Signed-off-by: NGeorge Spelvin <linux@horizon.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 725c7b57 (ata: libahci_platform: move port_map parameters
into the AHCI structure) moves flags into the struct ahci_host_priv's
.flags field, which causes compiler warnings on 64-bit builds when that
value is cast to a void * pointer. Cast to an unsigned long so that the
subsequent cast to a pointer doesn't produce a warning.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The ahci_platform driver is a generic driver using the libahci_platform
functions. Add a generic compatible to avoid having an endless list of
compatibles with no differences for the same driver.
Signed-off-by: NAntoine Ténart <antoine.tenart@free-electrons.com>

The current implementation of the libahci does not allow to use multiple
PHYs. This patch adds the support of multiple PHYs by the libahci while
keeping the old bindings valid for device tree compatibility.

This introduce a new way of defining SATA ports in the device tree, with
one port per sub-node. This as the advantage of allowing a per port
configuration. Because some ports may be accessible but disabled in the
device tree, the port_map mask is computed automatically when using
this.
Signed-off-by: NAntoine Ténart <antoine.tenart@free-electrons.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch moves force_port_map and mask_port_map into the
ahci_host_priv structure. This allows to modify them into the AHCI
framework. This is needed by the new dt bindings representing ports as
the port_map mask is computed automatically.

Parameters modifying force_port_map, mask_port_map and flags have been
removed from the ahci_platform_init_host() function, and inputs in the
ahci_host_priv structure are now directly filed.
Signed-off-by: NAntoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Add the missing clk_disable_unprepare() before return from
imx_sata_enable() in the phy reset error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

APM X-Gene SoC AHCI SATA Host controller driver requires
some correction of Phy Control OOB timing for the
COMINIT/COMWAKE parameters to correctly interoperate with
different kinds of disks.
Signed-off-by: NLoc Ho <lho@apm.com>
Signed-off-by: NSuman Tripathi <stripathi@apm.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

As per SATA IO specification, when Host sends HOLD, the device takes
about 20DW latency to reply to HOLDA. In some case, device doesn't
response to HOLDA over 20DW and causes FIFO goes into over flow
condition. Due to this condition, device enumerations fails with
those devices. This patch adjust the watermark FIFO by increasing
the FIFO depth from 0x16(default) to 0x30 to address this issue.
Signed-off-by: NLoc Ho <lho@apm.com>
Signed-off-by: NSuman Tripathi <stripathi@apm.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

1871ee13 ("libata: support the ata host which implements a queue
depth less than 32") directly used ata_port->scsi_host->can_queue from
ata_qc_new() to determine the number of tags supported by the host;
unfortunately, SAS controllers doing SATA don't initialize ->scsi_host
leading to the following oops.

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
 IP: [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0
 PGD 0
 Oops: 0002 [#1] SMP
 Modules linked in: isci libsas scsi_transport_sas mgag200 drm_kms_helper ttm
 CPU: 1 PID: 518 Comm: udevd Not tainted 3.16.0-rc6+ #62
 Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.02.0002.122320131210 12/23/2013
 task: ffff880c1a00b280 ti: ffff88061a000000 task.ti: ffff88061a000000
 RIP: 0010:[<ffffffff814e0618>]  [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0
 RSP: 0018:ffff88061a003ae8  EFLAGS: 00010012
 RAX: 0000000000000001 RBX: ffff88000241ca80 RCX: 00000000000000fa
 RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8806194aa298
 RBP: ffff88061a003ae8 R08: ffff8806194a8000 R09: 0000000000000000
 R10: 0000000000000000 R11: ffff88000241ca80 R12: ffff88061ad58200
 R13: ffff8806194aa298 R14: ffffffff814e67a0 R15: ffff8806194a8000
 FS:  00007f3ad7fe3840(0000) GS:ffff880627620000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000058 CR3: 000000061a118000 CR4: 00000000001407e0
 Stack:
  ffff88061a003b20 ffffffff814e96e1 ffff88000241ca80 ffff88061ad58200
  ffff8800b6bf6000 ffff880c1c988000 ffff880619903850 ffff88061a003b68
  ffffffffa0056ce1 ffff88061a003b48 0000000013d6e6f8 ffff88000241ca80
 Call Trace:
  [<ffffffff814e96e1>] ata_sas_queuecmd+0xa1/0x430
  [<ffffffffa0056ce1>] sas_queuecommand+0x191/0x220 [libsas]
  [<ffffffff8149afee>] scsi_dispatch_cmd+0x10e/0x300
  [<ffffffff814a3bc5>] scsi_request_fn+0x2f5/0x550
  [<ffffffff81317613>] __blk_run_queue+0x33/0x40
  [<ffffffff8131781a>] queue_unplugged+0x2a/0x90
  [<ffffffff8131ceb4>] blk_flush_plug_list+0x1b4/0x210
  [<ffffffff8131d274>] blk_finish_plug+0x14/0x50
  [<ffffffff8117eaa8>] __do_page_cache_readahead+0x198/0x1f0
  [<ffffffff8117ee21>] force_page_cache_readahead+0x31/0x50
  [<ffffffff8117ee7e>] page_cache_sync_readahead+0x3e/0x50
  [<ffffffff81172ac6>] generic_file_read_iter+0x496/0x5a0
  [<ffffffff81219897>] blkdev_read_iter+0x37/0x40
  [<ffffffff811e307e>] new_sync_read+0x7e/0xb0
  [<ffffffff811e3734>] vfs_read+0x94/0x170
  [<ffffffff811e43c6>] SyS_read+0x46/0xb0
  [<ffffffff811e33d1>] ? SyS_lseek+0x91/0xb0
  [<ffffffff8171ee29>] system_call_fastpath+0x16/0x1b
 Code: 00 00 00 88 50 29 83 7f 08 01 19 d2 83 e2 f0 83 ea 50 88 50 34 c6 81 1d 02 00 00 40 c6 81 17 02 00 00 00 5d c3 66 0f 1f 44 00 00 <89> 14 25 58 00 00 00

Fix it by introducing ata_host->n_tags which is initialized to
ATA_MAX_QUEUE - 1 in ata_host_init() for SAS controllers and set to
scsi_host_template->can_queue in ata_host_register() for !SAS ones.
As SAS hosts are never registered, this will give them the same
ATA_MAX_QUEUE - 1 as before.  Note that we can't use
scsi_host->can_queue directly for SAS hosts anyway as they can go
higher than the libata maximum.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NMike Qiu <qiudayu@linux.vnet.ibm.com>
Reported-by: NJesse Brandeburg <jesse.brandeburg@gmail.com>
Reported-by: NPeter Hurley <peter@hurleysoftware.com>
Reported-by: NPeter Zijlstra <peterz@infradead.org>
Tested-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Fixes: 1871ee13 ("libata: support the ata host which implements a queue depth less than 32")
Cc: Kevin Hao <haokexin@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org

Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: NKiran Padwal <kiran.padwal21@gmail.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

In machines with multiple Silicon Image 3124 and/or 3132 cards, there is no
way to tell which card is the culprit when the sata_sil24 interrupt handler
gets a bad status.
Tested-by: NTim Small <tim@seoss.co.uk>
Signed-off-by: NTim Small <tim@seoss.co.uk>
Signed-off-by: NTejun Heo <tj@kernel.org>

Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].

Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.
Signed-off-by: NRomain Degez <romain.degez@gmail.com>
Tested-by: NRomain Degez <romain.degez@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

This adds support for the integrated AHCI-compliant Serial ATA
controller present on the NVIDIA Tegra124 system-on-chip.
Signed-off-by: NMikko Perttunen <mperttunen@nvidia.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The Tegra124 SATA controller requires 4 clocks. Increase this constant
to be able to use them all.
Signed-off-by: NMikko Perttunen <mperttunen@nvidia.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.

So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@infradead.org>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

[linux-3.16-rc5/drivers/ata/pata_ep93xx.c:929]: (style) Checking if unsigned
variable 'irq' is less than zero.

Source code is

    irq = platform_get_irq(pdev, 0);
    if (irq < 0) {

but

    unsigned int irq;

$ fgrep platform_get_irq `find . -name \*.h -print`
./include/linux/platform_device.h:extern int platform_get_irq(struct
platform_device *, unsigned int);

Now using "int" type instead of "unsigned int" for "irq" variable.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80401Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NAndrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

libata-eh.c should handle AMNF error condition (error byte bit 0,
usually code 0x01) in libata-eh.c along with UNC as a media error so
SCSI stack can handle it properly (translation code 0x01 is already
present in libata-scsi.c) but was never passed down due to lack of
handling in EH.

While using linux-based machine (AMD 6550M-based notebook, PCI IDs for the
controller are 1022:7801 subsys 1025:059d) and ddrescue to salvage data
from failing hard drive (WD7500BPVT 2.5" 750G SATA2), I've found that pure
AMNF 0x01 error code generates generic "device error" that is retried
several times by SCSI stack instead of "media error" that is passed up to
software.

So we may assume deprecated AMNF error code is surely not dead yet, and
it's better for it to be handled properly. As we may see it is used by
modern enough devices, and used properly: drive returned AMNF only when IDs
for track cannot be read completely due to dying head or positioning,
otherwise it returned UNC(orrectables).

Not handling it causes wrong generic error code ("device error") reporting
down the stack, can damage failing drives further because of excessive
retries, and slows salvaging down a lot. Also, there is handling code in
libata-scsi.c for 0x01 AMNF error already.

https://bugzilla.kernel.org/show_bug.cgi?id=80031

tj: Shortened $SUBJ and moved its content to the first paragraph.
Signed-off-by: NAlexey Asemov <alex@alex-at.ru>
Signed-off-by: NTejun Heo <tj@kernel.org>

The sata on fsl mpc8315e is broken after the commit 8a4aeec8
("libata/ahci: accommodate tag ordered controllers"). The reason is
that the ata controller on this SoC only implement a queue depth of
16. When issuing the commands in tag order, all the commands in tag
16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata
malfunction. It makes no senses to use a 32 queue in software while
the hardware has less queue depth. So consider the queue depth
implemented by the hardware when requesting a command tag.

Fixes: 8a4aeec8 ("libata/ahci: accommodate tag ordered controllers")
Cc: stable@vger.kernel.org
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch fixes the dma state machine lockup due to the processing
of IDENTIFY DEVICE PIO mode command. The X-Gene AHCI controller
has an errata in which it cannot clear the BSY bit after the PIO setup
FIS. The dma state machine enters CMFatalErrorUpdate state and locks
up. This patch also removes the dma restart workaround from the read_id
function as the read_id function is only called by libata layer for
ATA_INTERNAL commands. But for some cases eg: PORT MULTIPLIER
and udev, the framework will enumerate using SCSI commands and it will
not call read_id function.
Signed-off-by: NLoc Ho <lho@apm.com>
Signed-off-by: NSuman Tripathi <stripathi@apm.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The subsequent patch will make use of them.
Signed-off-by: NLoc Ho <lho@apm.com>
Signed-off-by: NSuman Tripathi <stripathi@apm.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Spread-spectrum doesn't work with Cubox-i hardware, so we have to
disable this feature.  Add a DT property so that platforms can
indicate that this feature should not be enabled.

Having it as a negative property keeps existing DT files working.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Various SATA phy parameters are board specific, and therefore need to
be configured.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch removes support for s5pc100 ata because of no more support
S5PC100 SoC in mainline.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>