Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ath_printk and ath_<level> similar to
dev_printk and dev_<level> from device.h

This allows a more gradual rename of ath_print
to to ath_dbg or perhaps ath_debug.

This basically removes debug.h leaving
only an #define ath_printk ath_dbg
there and moving all the ATH_DBG_<foo>
enums to ath.h

I do not think there's much purpose for struct
ath_common * being passed to the ath_printk
functions, but perhaps there might be.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Since we report tx acks to the protocol stack, add the needed
 flag to hw_flags. This way we'll also use the new AP probing mechanism.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Correctly report failure to stop RX DMA
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Stop ANI durring reset to prevent false PHY error reports
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Always free tx buffers before reset, since we also empty hw queues.
 If we don't and a queue gets stuck, we'll never decrease txq_len and sw
 will keep thinking the queue is still stuck even after reset.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * By skipping tx power table calibration we also skip setting
 tx power table on hw. Make sure we always write tx power table
 on hw since it gets cleared on reset.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This prepares the only place which uses the EWMA library so far for the
performance improved implementation coming up, which requires factor and
weight to be a power of two.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On WiSoc we cannot access mac register before it is resetted.
It will crash hardware otherwise.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AHB specific functions are now in ahb.c file. AHB bus is
compiled in when CONFIG_ATHEROS_AR231X is set in kernel.
All other platforms will use PCI bus.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add bus dependent revision read function which is used to
determine chipset's MAC before hardware is initialized.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To be able to support other busses than PCI check if pci device
structure is initialized.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split pci initialization into hardware specific
functions and softc structure initialization.
Make function naming similar to ones ath9k.
Introduce ath_bus_opts in ath5k for later
AHB bus integration.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Invert test and return early.
Move variable declarations to local scope.
Don't initialize variables to 0 unnecessarily.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes debugfs problems when a phy is renamed,
and is able to remove a bit of code that is no longer
needed.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 916448e7.

"As far as I can tell, either of these patches breaks multiple VIF
scenarios.  I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
  -- Ben Greear <greearb@candelatech.com>

http://marc.info/?l=linux-wireless&m=129123368719339&w=2Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.

Cc:stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * A diff between rfbuffer settings of turbo and non-turbo
 modes indicates there is a bit on bank 2 related to turbo operation
 (it's set on turbo modes). This bit is present on all radios except
 RF5413 that seems to have a completely different bank 2. Also
 since 2317 has the same rf-registers locations with 2425 and
 since the bit exists on 2317 I assume it also exists on 2425/2417).
 So in case we use turbo mode (40MHz) enable it on bank modification.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Clean up what's left of turbo mode, since we handle all
 register modifications (rfbuffer comes next) on code there
 is no need to have duplicated arrays.

 * Rename change_channel to skip_pcu on initvals.c as we did
 on reset.c
Signed-off-by: NNick Kossifidis <micklfemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Clean up CHANNEL_T(URBO), use AR5K_BWMODE_40MHZ instead
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Use correct clock value when setting OFDM timings on
 non-default bwmodes.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Don't return -EINVAL when trying to set tx power
 on RF5110 because AR5210 reset will fail. We need to
 add support for RF5110 and AR5210 eeprom in the future
 but for now just skip it.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Tweak phy activation -> rx delay for different bwmodes
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Since we set antenna flags on phy init and ack bitrate
 mode on pcu init, there is no need to save/restore sta_id
 flags on ath5k_hw_reset. Also we don't need to re-set our
 mac address because it's not affected by resets.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Add synth-only channel change for AR2413/5413. When we call
 ath5k_reset with a channel ath5k_hw_reset will first try to
 set channel on PHY while PHY is running instead of doing a normal
 full reset. To do this phy_init has to change to implement this
 functionality.

 * Clean up change_channel flag, what it really did was skip PCU
 registers when setting initvals. This is done because on reset
 PCU registers are not affected (except the registers we set
 in pcu init and -due to hw problems- TSF). Use a new skip_pcu
 flag that's not misleading instead. In the future we might use
 that to also skip PCU reset and save us the TSF etc problems
 (needs testing because standard practice is to reset everything).

 * Use fast channel change only when setting channel, and set skip_pcu
 to false only on init. When we reset the card due to DMA or PHY
 problems skip pcu but never do a fast channel change.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Only set power table if we are changing channel/mode
 there is no need to recalculate and reset the power table
 all the time.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Set correct PLL settings for each bwmode
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Add spur mitigation filter support for half/quarter and turbo.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Tweak power detector delays on AR5111/AR5112 when
 using half/quarter modes.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Make sure we always set IFS timings even if no
 coverage class is set. If we don't we'll miss the
 needed changes for different bwmodes.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Set AR5K_DCU_GBL_IFS_MISC_TURBO_MODE flag on DCU when operating
 on 40MHz
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>