This is patch as550 from Alan Stern.

Apparently someone changed the SCSI core so that it no longer holds the
host lock when doing a device or bus reset.  usb-storage was updated at
the time, but the change was done carelessly.  Some of the code depends
on that lock being held.

This patch reintroduces the host lock where needed and tries to clarify
the comments explaining why the lock is necessary.  It also moves the
code that clears the TIMED_OUT and ABORTING bitflags so that it executes
as soon as the timed-out command has completed (and while the host lock
is held).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This appears to help some folk, please merge.
This patch relaxes reset timings.  There are some reports that it
helps make enumeration work better on some high speed devices.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the product ID and vendor ID for a Nokia CA-42 USB cable
to the list of devices handled by the pl2303 driver. The patch is
against 2.6.13.
Signed-off-by: NRobert Spanton <rds204@zepler.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that it's in use on other boards, a bug in the original code needs fixing.

There is no need for the PXA27x OHCI to set usb power during init, since
the hub driver in usbcore handles that. Those platform-specific power
control functions are also incorrect, and should therefore be removed.

Add a check to clear the OTG pin hold bit until such times OTG is
properly implemented.
Signed-Off-By: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some OHCI implementations have differences in the way the NDP register
(in roothub_a) reports the number of ports present. This patch allows the
platform specific code to optionally supply the number of ports. The
driver just reads the value at init (if not supplied) instead of reading
it every time its needed (except for an AMD756 bug workaround).

It also sets the value correctly for the ARM pxa27x architecture.
Signed-Off-By: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Evidently there are some boards which care a lot about this, but
as a rule it's been hard to notice.

OHCI_INTR_RD wasn't always cleared in the ohci irq handler.  On some
systems this means certain remote wakeup scenarios could seem to hang
(in an interrupt storm, RD never clearing).

From: "William Morrow" <William.Morrow@amd.com>
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this patch fixes an "Invalid argument" error returned by a write to an
endpoint-file after reopening it in the gadgetfs module in the kernel
2.6.12.

This was testet only with dummy_hcd module!
Signed-off-by: NPavol Kurina  <kurina@gmx.net>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>

Description: Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Routine cases like handoff-to-companion shouldn't trigger diagnostics.
This gets rid of some recently added log spamming.  It's routine for
hub_port_wait_reset() to return -ENOTCONN to indicate handoff from
highspeed hubs to companions, so an error message is incorrect.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

NVidia reports (via Mark Overby) that some of their EHCI controllers
don't like certain data structure addresses beyond the 2GB mark.
He provided an earlier version of this patch.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

One change may improve some S1 or S3 resume cases, and the other
seems mostly to explain some strange state "lsusb" would show.
Two fixes:

  - On resume, don't think about resuming any unpowered port, or
    resetting any port with OWNER set to the OHCI/UHCI companion.
    This will make some S1 and S3 resume scenarios work better.

  - PORT_CSC was not being cleared correctly in ehci_hub_status_data.
    This was visible at least through current versions of "lsusb",
    and might have caused some other hub related strangeness.

    The fix addresses all three write-to-clear bits, using the same
    approach that UHCI happens to use:  a mask of bits that are
    cleared in most writes to that port status register.

Original patch seems to have been from from William.Morrow@amd.com
and this version (from David) finishes the write-to-clear changes.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Three new device IDs for CP2101 USB to UART Bridge
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as558) removes from the UHCI driver a kernel timer used for
checking Full Speed Bandwidth Reclamation (FSBR).  The checking can be
done during normal root-hub polling; it doesn't need a separate timer.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as549) introduces two small changes in the HCD glue layer.
The first simply removes a redundant test.  The second allows root-hub
polling to continue for a single iteration after a host controller dies;
this is needed for the patch that follows.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.

This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
    * appletouch is a full kernel driver, no userspace program is necessary
    * appletouch can be interfaced with the synaptics X11 driver[2], in order
      to have touchpad acceleration, scrolling, two/three finger tap, etc.

This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.

Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: NStelian Pop <stelian@popies.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

here is a new and extended version of the sisusbvga (previously: sisusb)
driver. The patch is against 2.6.13 and updates the driver to version 0.0.8.

Additions include complete VGA/EGA text console support and a build-in
display mode infrastructure for userland applications that don't know
 about the graphics internals.

Fixes include some BE/LE issues and a get/put_dev bug in the previous
version.

Other changes include a change of the module name from "sisusb" to
"sisusbvga". The previous one was too generic IMHO.

Please note that the patch also affects the Makefile in
drivers/video/console as the driver requires the VGA 8x16 font in case
the text console part is selected.

Heavily tested, as usual. Please apply.

One thing though: I already prepared for removal of the "mode" field and
the changed "name" field in the usb_class_driver structure. This will
perhaps need some refinement depending on whether you/Linus merge the
respective core changes before or after 2.6.14.
Signed-off-by: NThomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

   This reverts 22af8878 commit.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch does a full cleanup of 'NULL checks before vfree', and a partial
cleanup of calls to kfree for all of drivers/ - the kfree bit is partial in
that I only did the files that also had vfree calls in them.  The patch
also gets rid of some redundant (void *) casts of pointers being passed to
[vk]free, and a some tiny whitespace corrections also crept in.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK.  Build and boot-tested on x86.  A similar patch has been
been in the -RT tree for some time.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NHenk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

sparse still complains about the htons usage, but I'll leave that for
others to fix.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch aggregates all modifications in the -mm tree and adds
complete ringtone support.

The following features are supported:
  - keyboard          full support
  - LCD               full support
  - LED               full support
  - dialtone          full support
  - ringtone          full support
  - audio playback    via generic usb audio diver
  - audio record      via generic usb audio diver

For driver documentation see: Documentation/input/yealink.txt
For vendor documentation see: http://yealink.comSigned-off-by: NHenk <Henk.Vergonet@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As sugested by Alan Stern here are a few code cleanups for onetouch.c:

-Check number of endpoints before directly referencing intf->endpoint[2]
-Use defined constants instead of magic numbers
-Revmove the non-ascii characters from copyright notice
-Make registration and deregistration messages more similar
Signed-off-by: NNick Sillik <n.sillik@temple.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This code looks at urb->transfer_dma, maps the page and takes the data.
I am looking for volunteers to contribute architectures other than i386
or to develop an architecure-neutral API for it (or point me that it
was done already).
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the field tt_usecs to ehci_qh and ehci_iso_stream, and sets it
appropriately when setting them up as periodic endpoints.  It records
the transation translator's think_time (added in last patch) plus the
downstream (i.e. low or full speed) bustime of the transfer associated
with each interrupt or iso frame, as calculated by usb_calc_bus_time.
Signed-off-by: NDan Streetman <ddstreet@ieee.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds think_time to the usb_tt struct and sets it appropriately
(measured in ns); this can help us implement better split transaction
scheduling.
Signed-off-by: NDan Streetman <ddstreet@ieee.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This wraps up the conversion of the "usbnet" driver structure, by
moving the Prolific PL-2201/2302 minidriver to a module of its own.
It also includes some minor cleanups to the remaining "usbnet" file,
notably removing that long changelog at the top.

Minor historical note:  Linux 2.2 first called the driver for
this hardware "plusb".
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds host-side RNDIS support to the "usbnet" driver, so Linux can talk
to various devices (often based on WinCE) that otherwise only Windows could
talk to.

Tested with little-endian Linux talking to a Linux-USB Ethernet/RNDIS based
peripheral.  This also includes updates from Eddie C. Dost <ecd@brainaid.de>
for big-endian SPARC Linux talking to a Nokia 9500 Communicator.

It's still marked as EXPERIMENTAL because this code is so young.  This
ought to let Linux to work with various cable modems that previously
would have been "Windows Only".
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Makes the CDC Ethernet support live in a separate driver module.
This module is a bit special since it exports utility functions
that are reused by the the Zaurus and RNDIS drivers, but it's
not "core" like usbnet itself.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This moves usbnet support for Zaurus and compatibles into its own module.
Other than exporting a couple of helper functions, this just involved
shuffling some code and updating the comments.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This moves the GeneSys GL620USB-A support into its own driver file.
It also fixes a "return wrong skb" glitch in the rx unbatching, as
recently reported, and adds some missing byteswaps in the special
"genelink" headers (so it might now work on big-endian Linux).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As with the "cdc_subset" and "asix" drivers, this just moves the net1080
support into its one driver module.  In this case there's a small bit of
extra cleanup involved, moving some funky framing logic into the tx_fixup()
routine (resolving a long overdue FIXME).

Minor historical note:  "usbnet" started out as "net1080", then got
generalized to make it easier for other network drivers to reuse the
urb queueing and fault management code here.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the ASIX AX8817x driver into its own file, just using
the "usbnet" infrastructure as a utility library.

 - As with "cdc_subset" this involved minor Kconfig/kbuild tweaks,
   moving code from one file to another, and exporting a few functions.

 - This includes updates from Jamie Painter to add (and use) a new hook
   to handle the different maximum transfer sizes for rx and tx sides.

 - Also from Jamie, some bugfixes:
    * MDIO byteorder (to address some PPC media negotiation problems);
    * Force alignment at key spots when using ax88772 framing (on some
      embedded hardware, the network stack will break otherwise);
    * Address some link reset problems.

It also makes this driver use the standard (5 seconds vs half second)
control timeouts used elsewhere in USB; and wraps a few lines before
the 80th column (which previously needed it).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch creates the first of several separate "minidriver" modules
for "usbnet".  This one handles only the very simplest hardware, which
can be handled almost entirely by the "usbnet" core.

    - Move device-specific bits into new "cdc_subset.c" driver,
      shrinking "usbnet" by a bunch;

    - Export the functions needed to support this minidriver
      (with EXPORT_SYMBOL_GPL);

    - Update Kconfig and kbuild accordingly.

This one handles about a dozen different device types, with the most
notable ones being Gumstix and most Linux-based PDAs (except Zaurus
running that ancient code from Sharp).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This starts to prepare the core of "usbnet" to know less about various
framing protocols that map Ethernet packets onto USB, so "minidrivers"
can be modules that just plug into the core.

  - Remove some framing-specific code that cluttered the core:

      * net->hard_header_len records how much space to preallocate;
        now drivers that add their own framing (Net1080, GeneLink,
	Zaurus, and RNDIS) will have smoother TX paths.  Even for
	the drivers (Zaurus, Net1080) that need trailers.

      * defines new dev->hard_mtu, using this "hardware" limit to
        check changes to the link's settable "software" mtu.

      * now net->hard_header_len and dev->hard_mtu are set up in the
        driver bind() routines, if needed.

  - Transaction ID is no longer specific to the Net1080 framing;
    RNDIS needs one too.

  - Creates a new "usbnet.h" header with declarations that are shared
    between the core and what will be separate modules.

  - Plus a couple other minor tweaks, like recognizing -ESHUTDOWN
    means the keventd work should just shut itself down asap.

The core code is only about 1/3 of this large file.  Splitting out the
minidrivers into separate modules (e.g. ones for ASIX adapters,
Zaurii and similar, CDC Ethernet, etc), in later patches, will
improve maintainability and shrink typical runtime footprints.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix

drivers/usb/misc/ldusb.c: In function `ld_usb_read':
drivers/usb/misc/ldusb.c:467: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c: In function `ld_usb_write':
drivers/usb/misc/ldusb.c:531: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 5)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 6)
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Deprecate the OSS USB drivers.

This patch includes spelling fixes by Lee Revell.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ohci-ppc-soc.c provides for a platform-specific callback mechanism for
when the HC is successfully probed or removed.  It turned out that none
of the 3 platforms using it need this facility. Also the required
include/asm-ppc/usb.h has never been accepted.  This patch removes the
callback feature and the include of <asm/usb.h>.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Avoid an annoying message that can appear if devices are disconnected
in the middle of a USB scatterlist operation.

Message noted in http://bugzilla.kernel.org/show_bug.cgi?id=4373
(but the real issue there seems to be a SCSI level hang).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use a more correct calculation for highspeed bit times.

  http://bugzilla.kernel.org/show_bug.cgi?id=3604

This sort if thing might start to make a difference now that the high
speed periodic scheduler is more complete -- and even getting used.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>