Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:

@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com

Split up crtc_state->base to hw where appropriate. This is done using the following patch:

@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x

@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com

intel_get_load_detect_pipe() needs to set uapi active,
uapi enable is set by the call to drm_atomic_set_mode_for_crtc(),
so we can remove it.

intel_pipe_config_compare() needs to look at hw state, but I didn't
change spatch to look at it. It's easy enough to do manually.

intel_atomic_check() definitely needs to check for uapi enable,
otherwise intel_modeset_pipe_config cannot copy uapi state to hw.

Changes since v1:
- Actually set uapi.active in get_load_detect_pipe().
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-3-maarten.lankhorst@linux.intel.com

Prepare to split up hw and uapi machinally, by adding a uapi and
hw alias. We will remove the base in a bit. This is a split from the
original uapi/hw patch, which did it all in one go.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-2-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

We are still looking at drm_crtc_state in a few places, convert those
to use intel_crtc_state instead.

Changes since v1:
- Move to before uapi/hw split.
- Add hunks for intel_pm.c as well.
Changes since v2:
- Incorporate Ville's feedback.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-1-maarten.lankhorst@linux.intel.com

Rename the encoder->crtc_mask to encoder->pipe_mask to better
reflect what it actually contains.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-3-ville.syrjala@linux.intel.comReviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>

The core no longer uses drm_crtc_state::mode with atomic drivers,
so let's stop frobbing it in the driver. For the user mode readout
we'll just use an on stack mode.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029145526.10308-1-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

We always pass mode==NULL to intel_get_load_detect_pipe(). Remove
the pointless function argument.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029132323.18113-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

The change from the uapi coordinates to the internal coordinates
broke the cursor on i845/i865 due to src and dst getting swapped.
Fix it.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 3a612765 ("drm/i915: Remove cursor use of properties for coordinates")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-1-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

smatch complains about
drivers/gpu/drm/i915//display/intel_display.c:14403 intel_set_dp_tp_ctl_normal() error: uninitialized symbol 'conn'.
because it has no way to determine that the loop must have an entry.
Tell the static analysers to ignore the local, it will always be set.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028142652.1987-2-chris@chris-wilson.co.uk

i915_irq.c is large. One reason for this is that has a large chunk of
the GT render power management stashed away in it. Extract that logic
out of i915_irq.c and intel_pm.c and put it under one roof.

Based on a patch by Chris Wilson.
Signed-off-by: NAndi Shyti <andi.shyti@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191024211642.7688-1-chris@chris-wilson.co.uk

The change to skip the PCH reference initialization during fastboot
did end up breaking FDI. To fix that let's try to do the PCH reference
init whenever we're disabling a DPLL that was using said reference
previously.

Cc: stable@vger.kernel.org
Tested-by: NAndrija <akijo97@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112084
Fixes: b16c7ed9 ("drm/i915: Do not touch the PCH SSC reference if a PLL is using it")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022185643.1483-1-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

gen4+ supports fp16 pixel formats on the primary planes. Add the
relevant code.

On ivb fp16 scanout is slightly busted. The output from the plane will
have 1/4 the expected value. For the primary plane we would have to
use the pipe gamma or pipe csc to correct that which would affect all
the other planes as well, hence we simply choose not to expose fp16
on the ivb primary plane. On hsw the primary plane got fixed.

On gmch platforms I observed that the plane width must be below 2k
pixels with fp16 or else we get a corrupted image. This limitation
does not seem to be documented in bspec. I verified the exact limit
using the chv pipe B primary plane since it has windowing capability.
The stride limits are unaffected by fp16.

v2: Rebase on top of icl fp16
    Split thea gen4+ primary plane bits into a separate patch
    Deal with HAS_GMCH()
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-9-ville.syrjala@linux.intel.com

skl+ supports fp16 pixel formats on all universal planes. Add the
necessary bits to expose that capability. The main different to
icl is that we can't scale fp16, so need to add the relevant
checks.

v2: Rebase on top of icl fp16
    Split skl+ bits into a separate patch
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-8-ville.syrjala@linux.intel.com

Now that the planes declare their minimum cdclk requirements properly
we don't need to check the cdclk in skl_max_scale() anymore. Just check
against the maximum downscale ratio, and move the code next to it's
only caller.

v2: Add a comment explaining the HQ vs. not thing
Reviewed-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-7-ville.syrjala@linux.intel.com

The normal cdclk handling now takes care of making sure the
plane's pixel rate doesn't exceed the spec appointed percentage
of the cdclk frequency. Thus we can nuke
skl_check_pipe_max_pixel_rate().
Reviewed-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-6-ville.syrjala@linux.intel.com

Various pixel formats and plane scaling impose additional constraints
on the cdclk frequency. Provide a new plane->min_cdclk() hook that
will be used to compute the minimum acceptable cdclk frequency for
each plane.

Annoyingly on some platforms the numer of active planes affects
this calculation so we must also toss in more planes into the
state when the number of active planes changes.

The sequence of state computation must also be changed:
1. check_plane() (updates plane's visibility etc.)
2. figure out if more planes now require update min_cdclk
   computaion
3. calculate the new min cdclk for each plane in the state
4. if the minimum of any plane now exceeds the current
   logical cdclk we recompute the cdclk
4. during cdclk computation take the planes' min_cdclk into
   accoutn
5. follow the normal cdclk programming to change the
   cdclk frequency. This may now require a modeset (except
   on bxt/glk in some cases), which either succeeds or
   fails depending on whether userspace has given
   us permission to perform a modeset or not.

v2: Fix plane id check in intel_crtc_add_planes_to_state()
    Only print the debug message when cdclk needs bumping
    Use dev_priv->cdclk... as the old state explicitly
Reviewed-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-5-ville.syrjala@linux.intel.com

check_digital_port_conflicts() is done needlessly late. Move it earlier.
This will be needed as later on we want to set any_ms=true a bit later
for non-modesets too and we can't call this guy without the
connection_mutex held.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-4-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

So far we've sort of protected the global state under dev_priv with
the connection_mutex. I wan to change that so that we can change the
cdclk even for pure plane updates. To that end let's formalize the
protection of the global state to follow what I started with the cdclk
code already (though not entirely properly) such that any crtc mutex
will suffice as a read lock, and all crtcs mutexes act as the write
lock.

We'll also pimp intel_atomic_state_clear() to clear the entire global
state, so that we don't accidentally leak stale information between
the locking retries.

As a slight optimization we'll only lock the crtc mutexes to protect
the global state, however if and when we actually have to poke the
hw (eg. if the actual cdclk changes) we must serialize commits
across all crtcs so that a parallel nonblocking commit can't get
ahead of the cdclk reprogamming. We do that by adding all crtcs to
the state.

TODO: the old global state examined during commit may still
be a problem since it always looks at the _latest_ swapped state
in dev_priv. Need to add proper old/new state for that too I think.

v2: Remeber to serialize the commits if necessary
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-3-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Replace sampling the engine state every so often with a periodic
heartbeat request to measure the health of an engine. This is coupled
with the forced-preemption to allow long running requests to survive so
long as they do not block other users.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: NJon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191023133108.21401-5-chris@chris-wilson.co.uk

On ILK+ the documented min hdisplay is 64, min hblank is 32, and min
vblank is 5. On earlier platforms min hblank is also 32, and min
vblank is 3. Make sure the mode satisfies those limits.

There are further limits for HDMI and pfit use cases, but we'll check
for those in a more specific location.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718144340.1114-2-ville.syrjala@linux.intel.comReviewed-by: NManasi Navare <manasi.d.navare@intel.com>

This way it's easier to figure out what didn't match when we have
multiple pipes enabled.

v2: pass drm_crtc and use the more common [CRTC:%d:%s] format
    (Ville)
v3: use struct intel_crtc type to pass crtc around (Ville)
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015164029.18431-5-lucas.demarchi@intel.com

The new line is already added by pipe_config_mismatch(), so the callers
shouldn't add it.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011010907.103309-5-lucas.demarchi@intel.com

In the transcoder port sync mode, the slave transcoders mask their vblanks
until master transcoder's vblank so while disabling them, make
sure slaves are disabled first and then the masters.

v5:
* Dont pass dev priv to get_slave_crtc (Ville)
v4:
* Obtain slave state from master (Maarten)
v3:
* Rebase
v2:
* Use the intel_old_crtc_state_disables() helper

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-6-manasi.d.navare@intel.com

This clears the transcoder port sync bits of the TRANS_DDI_FUNC_CTL2
register during crtc_disable().

v3:
* Rebase on maarten's patches
v2:
* Directly write the trans_port_sync reg value (Maarten)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-5-manasi.d.navare@intel.com

As per the display enable sequence, we need to follow the enable sequence
for slaves first with DP_TP_CTL set to Idle and configure the transcoder
port sync register to select the corersponding master, then follow the
enable sequence for master leaving DP_TP_CTL to idle.
At this point the transcoder port sync mode is configured and enabled
and the Vblanks of both ports are synchronized so then set DP_TP_CTL
for the slave and master to Normal and do post crtc enable updates.

v11:
* Rebase (Manasi)
v10:
* in trans sync mode, dont stop link train for tgl (Manasi)
v9:
Remove update_scanline_offset to rebase on Maarten's patch (Manasi)
v8:
* Rebase on Maarten's patches (Manasi)
v7:
* Use ffs(slaves) to get slave crtc (Ville)
v6:
* Modeset implies active_changed, remove one condition (Maarten)
v5:
* Fix checkpatch warning (Manasi)
v4:
* Reuse skl_commit_modeset_enables() hook (Maarten)
* Obtain slave crtc and states from master (Maarten)
v3:
* Rebase on drm-tip (Manasi)
v2:
* Create a icl_update_crtcs hook (Maarten, Danvet)
* This sequence only for CRTCs in trans port sync mode (Maarten)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-4-manasi.d.navare@intel.com

After the state is committed, we readout the HW registers and compare
the HW state with the SW state that we just committed.
For Transcdoer port sync, we add master_transcoder and the
salves bitmask to the crtc_state, hence we need to read those during
the HW state readout to avoid pipe state mismatch.

v11:
* Move master trans init to get pipe_Config hooks (Ville)
v10:
* Initialize master_tarnscoder readout for all platforms (Ville)
v9:
* Initialize master_transcoder = INVALID at get config (Ville)
v8:
* Use master_select -1, address TRANS_EDP case (Ville)
* Rename master_transcoder to _readout (Lucas)
v7:
* NDont read HW state for DSI
v6:
* Go through both parts of HW readout (Maarten)
* Add a WARN if the same trans configured as
master and slave (Ville, Maarten)
v5:
* Add return INVALID in defaut case (Maarten)
v4:
* Get power domains in master loop for get_config (Ville)
v3:
* Add TRANSCODER_D (Maarten)
* v3 Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2:
* Add Transcoder_D and MISSING_CASE (Maarten)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-3-manasi.d.navare@intel.com

In case of tiled displays where different tiles are displayed across
different ports, we need to synchronize the transcoders involved.
This patch implements the transcoder port sync feature for
synchronizing one master transcoder with one or more slave
transcoders. This is only enbaled in slave transcoder
and the master transcoder is unaware that it is operating
in this mode.
This has been tested with tiled display connected to ICL.

v7:
* Rebase on Maarten's patches
v6:
* Use master_trans +1 and address missing trans_edp case (Ville)
v5:
* Add TRANSCODER_D case and MISSING_CASE (Maarten)
v4:
Rebase
v3:
* Check of DP_MST moved to atomic_check (Maarten)
v2:
* Do not use RMW, just write to the register in commit (Jani N)

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-2-manasi.d.navare@intel.com

In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.

v6:
Rebase (manasi)
v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-1-manasi.d.navare@intel.com

Despite the its name dirty_pipes refers to crtc indexes. Let's
change its behaviout to match the name.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011200949.7839-4-ville.syrjala@linux.intel.comReviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Replace the hand rolled stuff with drm_encoder_mask() when populating
possible_clones, and rename the function to
intel_encoder_possible_clones() to make it clear what it's used for.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-1-ville.syrjala@linux.intel.comReviewed-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>

Unlike other planes the cursor currently handles 180 degree rotation
adjustment during the hardware programming phase. Let's move that
stuff into intel_cursor_check_surface() to match how we do things
with other plane types.

And while at we'll plop in the final src x/y coordinates (which will
actually always be zero) into the src rect and color_plane[0].x/y,
just for some extra consistency.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015152757.12231-1-ville.syrjala@linux.intel.comReviewed-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>

In TGL there we are missing the initialization of port G.
Do the same as for other ports.
Signed-off-by: NKhaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191008220905.18278-1-khaled.almahallawy@intel.com

Prepare the mode readout for the uapi vs. hw state split.
We'll want to do all readout into the hw state.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927131432.15978-4-ville.syrjala@linux.intel.com

Prepare the connector/encoder mask readout for the uapi vs. hw
state split. We'll want to do all readout into the hw state.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927131432.15978-2-ville.syrjala@linux.intel.com

Prefer the intel_ types in intel_legacy_cursor_update() over the
drm_ types. Should make it easier to adapt this to the uapi vs. hw
state split.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927131432.15978-1-ville.syrjala@linux.intel.com

Once we do the hw vs. uapi split we can no longer use
drm_atomic_helper_calc_timestamping_constants() as it'll
consult the uapi state instead of the hw state.

So let's just update the vblank timestamping constants whenever
we update the scanline offset. We use both to convert the hw
scanline count to something which matches the software timing
values.

First I thought to put these into intel_crtc_vblank_on() but
we may want to get the scanline counter value before that (eg.
from some early tracepoints), so let's stick to updating them
a bit earlier than intel_crtc_vblank_on().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191007114943.29307-3-ville.syrjala@linux.intel.com

Use the new drm_rect_init() helper where appropriate.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190930134214.24702-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Use the newly introduced drm_rect_translate_to() instead
of hand rolling it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190930134214.24702-3-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

While not all platforms allow us to change the cdclk frequency
we should still verify that the fixed cdclk frequency isn't
too low. To that end let's cook up a .modeset_calc_cdclk()
implementation that only does the min_cdclk vs. actual cdclk
frequency check for such platforms.

Also we mustn't forget about double wide pipe on gen2/3 when
doing this.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708125325.16576-11-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>