This patch migrates most of the rx producer ring variables to a new
tg3_rx_prodring_set structure and modifies the code accordingly.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Later patches are going to complicate the ring initialization routines.
This patch breaks out the setup and teardown of the rx producer rings
into separate functions to make the code more readable.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves where the jumbo capable and msi support flags are
located.  This is prep work for the addition of msix support flags.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch separates the code that sets up the mini producer ring from
the code that sets up the jumbo producer rings.  The 5717 asic rev
devices do not have a mini ring, but do have a jumbo frame
implementation similar to the 5704 and previous devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes up the NVRAM detection switch statements to conform
to the kernel coding style.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device firmware uses the MDIO bus during early setup.  If the driver
modifies the MDIO bus configuration while it is in use by the firmware,
any number of bad things can happen.  This patch delays MDIO setup until
after the firmware posts its magic signature, signifying initialization
is complete.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
 - no_ether_link          : If set to 1, do not use ETHER_LINK
 - ether_link_active_low  : If set to 1, ETHER_LINK is active low.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On TI's DA850/OMAP-L138 EVM, MAC address is stored in SPI
flash which is accessed using MTD interface.

This patch delays the initialization of DaVinci EMAC driver
by changing module_init to late_initcall. This helps SPI and
MTD drivers to get initialized before EMAC thereby enabling
EMAC driver to read the MAC address while booting and use it.

Tested with NFS on DM644x, DM6467, DA830/OMAP-L137 and
DA850/OMAP-L138 EVMs.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix lmc_proto_type() invocation.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Better small packet receive performance.
- Better handling of Flow control on 5709.
- Fixed iSCSI TMP ABORT TASK problem.
- Added iSCSI TCP timestamp option.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TX completions were running in a workqueue queued by the ISR.  This
patch moves the processing of TX completions to an existing RSS NAPI
context.
Now each irq vector runs NAPI for one RSS ring and one or more TX
completion rings.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we downshift to MSI/Legacy if we don't get enough vectors for
cpu_count RSS rings plus cpu_count TX completion rings.  This patch
allows running MSIX with the vector count that the platform provides.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we have three types of RX rings.

1) Default ring - services rx_ring for broadcast/multicast, handles
firmware events, and errors.

2) TX completion ring - handles only outbound completions.

3) RSS ring - handles only inbound completions.

This patch gets rid of the default ring type and moves it's functionality
into the first RSS ring.  This makes better use of MSIX vectors since
they are a limited resource on some platforms.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bonding: Have bond_check_dev_link examine netif_running

	Some network devices do not call netif_carrier_off when they
are set administratively down.  Have the bonding link check function
also inspect the netif_running state.  Ignore netif_running if the
bond_check_dev_link function is called with "reporting" set, as in that
case it's inspecting the capabilities of the non-netif_carrier device
driver.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

max_bonds is of type int and cannot be greater than INT_MAX.
Signed-off-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding can use compare_ether_addr() in bond_release.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propogate the vlan_features of the slave devices to the bonding
master device, using the same logic as for regular features.

	Tested by Or Gerlitz <ogerlitz@voltaire.com>, who also removed
the debug logic from the original test patch.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the places in debugfs.c are missing a NULL check on the return value of
get_zeroed_page API call. Added required NULL check at appropriate places.
Signed-off-by: NKiran Divekar <kirandivekar@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that cfg80211 functions are added and wext converted to use wext-compat
functions, remove wext structures and disabled code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stats worker no longer poll stats from device anymore. It's still
needed to poll device control channel for connect/disconnect events,
so rename stats worker as device poller.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 get_station and convert SIOCGIWRATE and get_wireless_stats
to cfg80211.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 add_key/del_key/set_default_key and convert wext to use theim.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 set_channel and convert wext to use it.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add cfg80211 connect functions for station and ad-hoc modes and
convert wext to use theim.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Random essid must be set to turn on radio when not connected. If device is
in ad-hoc mode, this results 'media connect' indications with the random
essid which should be ignored.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use is_zero_ether_addr() and is_broadcast_ether_addr() instead of
memcmp against ffff_bssid/zero_bssid.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move link up/down work to separate functions and use local array
for allocating memory for info structure instead of kzmalloc.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Increase scan delay from 1 sec to 6 sec. Spec says that scan by
OID_802_11_BSSID_LIST_SCAN completes in 6 seconds.
Before rfkill patch too short delay was not problem as device was
always active (radio on) and performing background scanning.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Buffer used for bssid list might be too small. Change rndis_query_oid()
to return required buffer length to caller and make rndis_check_bssid_list()
resize buffer when needed.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

OID_802_11_BSSID_LIST_SCAN clears device's bssid list, so retrieve
current bssid list from device before issuing new scan.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setting WPA keys with OID_802_11_ADD_KEY sometimes trigger
instant media connect indication. These indications are extranous and
should be ignored, as otherwise driver would send reassociation event to
userspace which in this case is not needed.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>