fib_select_default() is a complete NOP, and completely pointless
to invoke, when we have no more than 1 default route installed.

And this is far and away the common case.

So remember how many prefixlen==0 routes we have in the routing
table, and elide the call when we have no more than one of those.

This cuts output route creation time by 157 cycles on Niagara2+.

In order to add the new int to fib_table, we have to correct the type
of ->tb_data[] to unsigned long, otherwise the private area will be
unaligned on 64-bit systems.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>

Nobody alive seems to recall when they last were useful.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DCB enabled X540 devices are not responding to pause frames
due to a missing register set that was added for these
devices that did not exist in other devices.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X540 device has a smaller packet buffer but the DCB configuration
never took this into account. Under stress this can result in the DMA
engine hanging and TX Unit hang occurring to reset the device. This
patch reworks the packet buffer allocation routine used for DCB on
82599 and X540 devices to account for RX packet buffer sizes.

This fixes the immediate hang. We should consolidate the various
hardware specific routines for configuring features into a single
routine. This will make it much harder to miss feature cases like
this.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

x540 has the same device capability word in the EEPROM as 82599.
This patch renames ixgbe_get_device_caps_82599 to
ixgbe_get_device_caps_generic, moves it to ixgbe_common.h and
sets up the function pointer for x540.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

100H is not supported on this HW, but the bit is set on the PHY.
This can result in link at 100F when advertising only 1000F.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add new device ID supported by ixgbe.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

HW can upload EEPROM content from flash while
in a middle of checksum calculation. Take NVM ownership for the whole
process of checksum update.

Call ixgbe_read_eerd_generic() and ixgbe_write_eewr_generic() directly to
avoid double take of semaphores which leads to long loading times.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since msleep might not sleep for the desired amount when less
than 20ms use usleep_range.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disable KR to KX4/KX downshift on 82599 backplane devices when
LESM (Link Establishment State Machine) is enabled in FW. Those
features cannot co-exist as they both manipulate the same registers.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhillip Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Relaxed ordering can lead to issues with some chipsets.

This patch makes sure that it is disabled by default and
not only when DCA is on.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Factored out the common start_hw code into a new function
ixgbe_start_hw_gen2() so that it can be used by x540 and 82599.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>

Set ixgbe_identify_82599() as static
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some 82598 parts have LAN0 disabled and LAN1 enabled and the LAN ID bits in
Device Status register report the NIC as having only LAN1 as enabled. This
causes ixgbe_set_lan_id_multi_port_pcie() to set bus->func = 1 which is
incorrect.

Force bus->func to 0 when LAN0 is disabled in the EEPROM.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The value of status was incorrectly tested. Also whitespace cleanup.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With the app data on the kernel dcb_app list we no longer
need to specifically handle them in ixgbe for the CEE case.
So now we can remove app handling logic and check when the
hw is configured if the app data matches the hardware
configuration in set_hw_all().

If it does not match then we can reconfigure.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Naga Chumbalkar <nagananda.chumbalkar@hp.com>:

If ASPM L0s needs to be disabled due to HW errata, do it prior to
"enabling" the device. This way if the kernel ever defaults its
aspm_policy to POLICY_POWERSAVE, then the e1000e driver will get a
chance to disable ASPM on the misbehaving device *prior* to calling
pci_enable_device_mem(). This will be useful in situations
where the BIOS indicates ASPM support on the server by clearing the
ACPI FADT "ASPM Controls" bit.

Note:
The kernel (2.6.38) currently uses the BIOS "default" as its aspm_policy.
However, Linux distros can diverge from that and set the default to
"powersave".

v2: o cleanup namespace pollution of e1000e_disable_aspm(),
    o fix type and initialization of the new aspm_disable_flag in a few
      functions, and
    o redefine FLAG2_DISABLE_ASPM_L0S to the first unused bit in
      adapter->flags2.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just move the unlock down a bit because it unlocks too
early leaving a chance for get_stats64() run in parallel
while it is still accessing the stats.
Signed-off-by: NFlavio Leitner <fleitner@redhat.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This switches the e1000e driver to use the new VLAN interfaces.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>

Correct the log message when driver loads.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With durations less than 20ms, the jiffies or legacy timer backed msleep()
may sleep ~20ms which might not be what the caller expects.  Instead, it
is recommended to use the hrtimers backed usleep_range().  For more, see
Documentation/timers/timers-howto.txt.  Issues reported by checkpatch.

In addition, remove unnecessary sleep in e1000e_write_nvm_spi().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The code for thermal sensor checking should be wrapped into a function.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Comment spelling fix.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the documentation for the anti-spoofing feature in the HW.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a revised patch that permits a shifted access to the
LAN9221 registers.  More specifically:

 It adds a shift parameter in the platform_data.
 It introduces an ops in smsc911x_data.
 A choice of access function to use at run-time.
 Four new shifted access function.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some devices, the VPD block is relocated to a different area in
NVRAM.  The original location can still contain old, but still valid VPD
data.  This patch changes the code to look for an extended VPD block in
NVRAM.  If one is found, that block is used for all VPD operations
instead.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds jumbo frame loopback test support to the ethtool
selftest.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reimplements the size preprocessor constants of the stats and
ethtool test string arrays.  The size is calculated at compile time
rather than using static constants.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch monitors the error bit of the status word within the status
block.  If it is set, the driver will dump the driver state after
validating the error and then reset the chip.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current amount of information provided in the output of a tx timeout
is insufficient to determine a root cause.  This patch replaces the
terse, four-register status output with a more complete body of
information.  For PCIe devices, the full register space is dumped.  For
other devices, select registers are dumped instead.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some RNDIS devices don't respond on the control channel until polled
on the status channel.  In particular, this was reported to be the
case for the 2Wire HomePortal 1000SW and for some Windows Mobile
devices.

This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk>
which is currently applied by Mandriva.
Reported-by: NMark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool support to configure RX, TX and other channels. combined field
in struct ethtool_channels to reflect set of channel (RX, TX or other).
Other channel can be link interrupts, SR-IOV coordination etc.

ETHTOOL_GCHANNELS will report max and current number of RX channels,
max and current number of TX channels, max and current number of other channel
or max and current number of combined channel.

Number of channel can be modify upto max number of channel through
ETHTOOL_SCHANNELS command.

Ben Hutchings:
o define 'combined' and 'other' types.  Most multiqueue drivers pair up RX and TX
  queues so that most channels combine RX and TX work.
o Please could you use a kernel-doc comment to describe the structure.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6

The "iavcc" and "iadev" cases are obvious.

The intr_status and frmr_intr cases are reading a register to clear
the chip status.  This driver is pretty old and creaky, and uses
volatile pointer dereferences to do register I/O when it should be
using readl() and friends.  However that it outside of the scope of
these changes.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following warnings:

net/9p/client.c:1305:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
net/9p/client.c:1370:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
net/9p/client.c:1769:18: warning: variable ‘total’ set but not used [-Wunused-but-set-variable]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>