Restructure the sound/soc/intel/ directory: create common folder, and move
sst common files here.
Signed-off-by: NJie Yang <yang.jie@intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The smatch tool report warning:
  ...
    CHECK   sound/soc/intel/sst-haswell-pcm.c
  sound/soc/intel/sst-haswell-pcm.c:1110 hsw_pcm_probe() error: buffer overflow\
'hsw_dais' 4 <= 4
  sound/soc/intel/sst-haswell-pcm.c:1112 hsw_pcm_probe() error: buffer overflow\
'hsw_dais' 4 <= 4
  ...
fix it by use its own struct member for post-process module, rather than sharing
unused pcm member.
Signed-off-by: NLu, Han <han.lu@intel.com>
Acked-by: NJie Yang <yang.jie@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Check waves state before set parameter through ipc to prevent unexpected
operation. Also remove redundant check.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Intel MID DMA driver is going to be removed, commit should be a few lines
down near to dmaengine_slave_config() call in order to not confuse and at
quick look Synopsys DesignWare does seem to use some of the slave config
structure fields (see drivers/dma/dw/core.c: dwc_config()).
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Intel MID DMA driver is going to be removed by the coming commit
36111da7 ("dmaengine: intel-mid-dma: remove the driver") in spi.git
tree. Since there are no users for SST_DMA_TYPE_MID type the support for it
can be removed from here in advance.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The jack creation code was in rt5670 codec driver before due to the
jack resources (gpio/irq) were defined under the node of codec device
in ACPI on Braswell. We used the snd_soc_jack_new() to create a jack
instance.

But now snd_soc_jack_new() is removed from upstream and we can't
use snd_soc_card_jack_new() in codec driver, so we move the jack
creation code to machine driver and pass the jack instance to codec
driver for further processing.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NJin Yao <yao.jin@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

On Braswell, we need to add some machine specific setting before suspend
and after resume. For example, disable/enable jack detection in codec so
use snd_soc_card suspend_pre and resume_post ops for this purpose.
Signed-off-by: NJin Yao <yao.jin@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Merge branch 'topic/jack' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel

Merge branch 'topic/rt5670' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel

Each kcontrol command includes a line of parameters up to 128 bytes.
kcontrol command to set param:
    cset "name='Waves Set Param' <0x01,0xff,...>"
or
    cset-bin-file "name='Waves Set Param' <path/to/binary/config/file>"

The parameter lines are stored in a buffer array, so can be read back from
buffer rather than from DSP, and be relaunched to DSP when resume from RTD3.
The buffer size is 160 parameter lines.
kcontrol command to reset the buffer:
    cset "name='Waves Set Param' 0xff"

alsa-lib v1.0.29 or commit 6ea14c36 and f47480af are required to support the
kcontrol commands.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add function to set parameters to module waves. The parameters can be set
only when module is enabled, and parameter size is limited to 500 Bytes.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add kcontrol to enable/disable module waves. IPC is valid only when module
is loaded. Also track module state over suspend so it's state can be restored
on resume.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Try to load module waves and allocate runtime blocks for it if the firmware
image of module waves exists.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add a general method to load firmware image, and apply to base firmware
image loading. With the method, the driver will support loading multiple
different modules in order to support different features.
Signed-off-by: NLu, Han <han.lu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Merge branch 'fix/intel' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel

Linux 4.0-rc3

We force enable "Mic Det Power" when a jack is inserted. Also, we
set codec idle_bias_off = true. As a result, codec driver will not
suspend as we expect.

On Braswell, we don't need the jack detection when suspend but need
it after resume, so export the jack suspend/resume APIs which are
provided for machine driver to control during suspend/resume.
Signed-off-by: NJie Yang <yang.jie@intel.com>
Signed-off-by: NJin Yao <yao.jin@linux.intel.com>
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds the IRQ function support of rt5670. We use a flag
named dev_gpio in platform data to inform codec driver if the IRQ
function is used or not. Also, we export rt5670_set_jack_detect
for machine driver to pass the jack point.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

A playback noise happens after suspend/resume on Braswell. The issue is due to
the codec PLL and codec ASRC are not enabled correctly due to the incorrect
sysclk setting after resume. This patch resets the sysclk source setting in
platform clock control widget handler.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NJin Yao <yao.jin@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Linux 4.0-rc3

Conflicts:
	sound/soc/codecs/rt5670.c

Currently, is_sys_clk_from_pll check sysclk source by reading codec
register value. And it will be invoked before updating dapm widget
power. In some machine driver, snd_soc_dai_set_sysclk is called in
dapm event to switch codec sysclk to RC clock in idle mode. And in
some use cases (such as syspend/resume) hw_params will not be called
when the dapm widget is powered up. As a result, is_sys_clk_from_pll
will return 0 although it is supposed to be 1.
To solve this, we let is_sys_clk_from_pll check sysclk sysclk_src
which is stored in private data and don't change the value of sysclk_src
when codec sysclk is switched to internal clock. The internal clock
can only be used in idle mode, so it sould be fine if we don't set
sysclk_src to internal clock.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The "Keep sysclk on if JD func is used" patch force enable/disable
pin in rt5670_set_dai_sysclk. But some machine driver call it in
dapm widget event. It will cause kernel crash.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull USB fixes from Greg KH:
 "Here's a round of USB fixes for 4.0-rc3.

  Nothing major, the usual gadget, xhci and usb-serial fixes and a few
  new device ids as well.

  All have been in linux-next successfully"

* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
  xhci: Workaround for PME stuck issues in Intel xhci
  xhci: fix reporting of 0-sized URBs in control endpoint
  usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
  USB: ch341: set tty baud speed according to tty struct
  USB: serial: cp210x: Adding Seletek device id's
  USB: pl2303: disable break on shutdown
  USB: mxuport: fix null deref when used as a console
  USB: serial: clean up bus probe error handling
  USB: serial: fix port attribute-creation race
  USB: serial: fix tty-device error handling at probe
  USB: serial: fix potential use-after-free after failed probe
  USB: console: add dummy __module_get
  USB: ftdi_sio: add PIDs for Actisense USB devices
  Revert "USB: serial: make bulk_out_size a lower limit"
  cdc-acm: Add support for Denso cradle CU-321
  usb-storage: support for more than 8 LUNs
  uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
  USB: usbfs: don't leak kernel data in siginfo
  xhci: Clear the host side toggle manually when endpoint is 'soft reset'
  xhci: Allocate correct amount of scratchpad buffers
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.0-rc3.

  Along with the atime fix that you know about, here are some other
  serial driver bugfixes as well.  Most notable is a wait_until_sent
  bugfix that was traced back to being around since before 2.6.12 that
  Johan has fixed up.

  All have been in linux-next successfully"

* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  TTY: fix tty_wait_until_sent maximum timeout
  TTY: fix tty_wait_until_sent on 64-bit machines
  USB: serial: fix infinite wait_until_sent timeout
  TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
  net: irda: fix wait_until_sent poll timeout
  serial: uapi: Declare all userspace-visible io types
  serial: core: Fix iotype userspace breakage
  serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
  console: Fix console name size mismatch
  tty: fix up atime/mtime mess, take four
  serial: 8250_dw: Fix get_mctrl behaviour
  serial:8250:8250_pci: delete unneeded quirk entries
  serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
  Change email address for 8250_pci
  serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
  Revert "tty/serial: of_serial: add DT alias ID handling"

Pull staging driver fixes from Greg KH:
 "Here are some IIO and staging driver fixes for 4.0-rc3.

  Details are in the shortlog, nothing major, mostly IIO fixes for
  reported issues.

  All have been in linux-next successfully"

* tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
  staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel
  staging: comedi: vmk80xx: remove "firmware version" kernel messages
  staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample()
  iio: ak8975: fix AK09911 dependencies
  iio: common: ssp_sensors: Protect PM-only functions to kill warning
  IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc
  Revert "iio:humidity:si7020: fix pointer to i2c client"
  iio: light: gp2ap020a00f: Select REGMAP_I2C
  iio: light: jsa1212: Select REGMAP_I2C
  iio: ad5686: fix optional reference voltage declaration
  iio:adc:mcp3422 Fix incorrect scales table
  iio: mxs-lradc: fix iio channel map regression
  iio: imu: adis16400: Fix sign extension
  staging: iio: ad2s1200: Fix sign extension
  iio: mxs-lradc: only update the buffer when its conversions have finished
  iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions
  iio: mxs-lradc: make ADC reads not disable touchscreen interrupts
  iio: mxs-lradc: separate touchscreen and buffer virtual channels
  iio: imu: inv_mpu6050: Prevent dereferencing NULL
  iio: iadc: wait_for_completion_timeout time in jiffies
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are two char/misc fixes for 4.0-rc3.

  One is a reported binder driver fix needed due to a change in the mm
  core that happened in 4.0-rc1.  Another is a mei driver fix that
  resolves a reported issue in that driver.

  Both have been in linux-next for a while"

* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: make device disabled on stop unconditionally
  android: binder: fix binder mmap failures

Pull "code of conflict" from Greg KH:
 "This file tries to set the rational basis for our code reviews, gives
  some advice on how to conduct them, and provides an excalation channel
  for any kernel developers if they so desire it"

[ Let's see how this works ]

* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Code of Conflict

Pull i2c fixes from Wolfram Sang:
 "A set of updates and bugfixes for the new designware-baytrail driver.

  And a documentation bugfix"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: add required clocks property to binding
  i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
  i2c: designware-baytrail: cross-check lock functions
  i2c: designware-baytrail: fix sparse warnings
  i2c: designware-baytrail: fix typo in error path
  i2c: designware-baytrail: describe magic numbers

Pull slave-dmaengine fixes from Vinod Koul:
 "This contains small fixes spread across the drivers"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mmp_pdma: fix warning about slave caps
  dmaengine: qcom_bam_dma: fix wrong register offsets
  dmaengine: bam-dma: fix a warning about missing capabilities
  dmaengine: ioatdma: workaround for incorrect DMACAP register
  dmaengine: at_xdmac: fix for chan conf simplification
  dmaengine: dw: don't handle interrupt when dmaengine is not used
  dma: mmp-tdma: refine dma disable and dma-pos update
  dmaengine: shdma: Move DMA stop to (runtime) suspend callbacks
  dmaenegine: mmp-pdma: fix irq handler overwrite physical chan issue

Pull arm64 fixes from Catalin Marinas:
 "arm64 and generic kernel/module.c (acked by Rusty) fixes for
  CONFIG_DEBUG_SET_MODULE_RONX"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  kernel/module.c: Update debug alignment after symtable generation
  arm64: Don't use is_module_addr in setting page attributes

Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.

Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.

Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.

This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.

The first symptom  was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.

Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.

Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Reported-by: NZIV-Asier Llano Palacios <asier.llano@cgglobal.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to handle an infinite timeout (0).

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: dcf01050 ("USB: serial: add generic wait_until_sent
implementation")
Cc: stable <stable@vger.kernel.org>	# v3.10
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In case an infinite timeout (0) is requested, the irda wait_until_sent
implementation would use a zero poll timeout rather than the default
200ms.

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.

Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>