Allow chips to indicates that they are input-only and thus cannot set
the output value.  This will be used by the gpio-etraxfs driver.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The change introduces BGPIOF_READ_OUTPUT_REG_SET flag for gpio-generic
GPIO chip implementation, which allows to get correct configured value
from reg_set register, input value is still get from reg_dat.
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When registering more than one platform device, it is
useful to set the gpio chip label in the platform data.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is no general support for 64-bit big endian accesses, so that is
left unsupported.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Acked-by: NAnton Vorontsov <anton@enomsg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It fixes the issue in gpio-generic that commit fb149218 (gpio/mxc: add
missing initialization of basic_mmio_gpio shadow variables) manged to
fix in gpio-mxc driver, so that other platform specific drivers do not
suffer from the same problem over and over again.

Changes since v1:
* Turn the last parameter of bgpio_init() "bool big_endian" into
  "unsigned long flags" and give those really quirky hardwares a
  chance to tell that reg_set and reg_dir are unreadable.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
[grant.likely: Fix big-endian usage to explicitly set BBGPIOF_BIG_ENDIAN]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Building a kernel with hotplug disabled results in a link failure:

  `bgpio_remove' referenced in section `___ksymtab_gpl+bgpio_remove' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o

This is because of bgpio_remove() is exported.  It is illegal to export
symbols which are discarded either at link time or as part of an
init/exit section.

Fix this by dropping the __devexit attributation from bgpio_remove().
Also drop the __devinit attributation from bgpio_init().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

include/linux/basic_mmio_gpio.h uses a spinlock_t without including any
of the spinlock headers resulting in this compiler warning.

include/linux/basic_mmio_gpio.h:51:2: error: expected specifier-qualifier-list before 'spinlock_t'

Explicitly include linux/spinlock_types.h to fix it.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail.  Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.

Changes since v1:
	- Register the gpio_chip in the platform device probe

1. https://lkml.org/lkml/2011/4/19/401Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Some platforms may have a number of GPIO that is less than the register
width of the peripheral.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.

These controllers may not provide any means of pin setup
(in/out/open drain).

The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

from include/asm-powerpc.  This is the result of a

mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm

Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly.  Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NZhang Wei <wei.zhang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Adds PPC32 RIO support.  Init code for the MPC85xx RIO ports and glue for the
STx GP3 board to use it.
Signed-off-by: NMatt Porter <mporter@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add RapidIO core include files.

The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
Signed-off-by: NMatt Porter <mporter@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>