- ide-dma.c is not a separate module

- ide-dma.c is not PCI specific anymore

- DMA is enabled by default nowadays

- link for Intel Zappa BIOS is dead

etc.

v2:
* Some comments should be preserved. (Noticed by Mark Lord)

Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

More complete documentation is available in Documentation/ide/ide-tape.txt.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drivers/ide/ide.c:801:18: warning: symbol 'flags' shadows an earlier one
drivers/ide/ide.c:732:16: originally declared here

Also fix some whitespace damage while at it.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move counting of sense bytes into the transfer loop.
Signed-off-by: NAndreas Schwab <schwab@suse.de>
Acked-by: NBorislav Petkov <petkovbb@gmail.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Pass 'struct request *rq' to ide_cd_check_ireason() from cdrom_newpc_intr()
and use ide_cd_check_ireason() also for REQ_TYPE_ATA_PC requests.

This fixes some hangs caused by not finishing the transfer before ending
the request and also makes use of 'ireason == 1' quirk for spurious IRQs.
Tested-by: NBrad Rosser <brad.rosser@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Control register of QD6580 should be setup before probing for devices.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Skip probing port if "hdx=noprobe" parameter was used for both devices on it.

* Obsolete "idex=noprobe" parameter - it only works for ide_generic, cmd640
  and PCI hosts in Compatibility mode (on alpha/x86/ia64/m32r/mips/ppc32).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Identical comment is present in ide_hwif_release_regions() documentation.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hpt366: fix section mismatch warnings

Fix following warnings:
WARNING: o-sparc64/vmlinux.o(.data+0x195a38): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt370
WARNING: o-sparc64/vmlinux.o(.data+0x195a40): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt370a
WARNING: o-sparc64/vmlinux.o(.data+0x195a48): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt372
WARNING: o-sparc64/vmlinux.o(.data+0x195a50): Section mismatch in reference from the variable hpt37x_info.0 to the variable .devinit.data:hpt372n

Replace a static array with a small switch resulting in
more readable code.
Mark the pci table __devinitconst.

A lot of variables are const but annotated __devinitdata.
Annotating them __devinitconst would cause a section type
conflict error when build for 64 bit powerpc.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Reported-by: NStefan Bader <stefan.bader@canonical.com>
Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Don't require platform code to be #ifdeffed according to whether
I2C is enabled or not ... if it's not enabled, let GCC compile out
all I2C device declarations.  (Issue noted on an NSLU2 build that
didn't configure I2C.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel
if there is no device at that port.
This patch adds a check_legacy_ioport call, so probe fails gracefully
and thus prevents the oops.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Commit 8b798c4d broke
alchemy build, fix it.  Pointed out by Adrian Bunk.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

While working on the PCA9564-platform driver, I sometimes had a glimpse at the
pxa-driver. I found some suspicious places, and this patch contains my
suggestions. Note: They are not tested, due to no hardware.

[JD: Some more fixes.]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NMike Rapoport <mike@compulab.co.il>
Tested-by: NEric Miao <ymiao3@marvell.com>

Each call to i2c_get_adapter() must be followed by a call to
i2c_put_adapter() to release the grabbed reference. Otherwise the
reference count grows forever and the adapter can never be
unregistered.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NVladimir Ananiev <vovan888@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata-core: fix kernel-doc warning
  sata_fsl: fix build with ATA_VERBOSE_DEBUG
  [libata] ahci: AMD SB700/SB800 SATA support 64bit DMA
  libata-pmp: clear hob for pmp register accesses
  libata: automatically use DMADIR if drive/bridge requires it
  power_state: get rid of write-only variable in SATA
  pata_atiixp: Use 255 sector limit

Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes build and few warnings when ATA_VERBOSE_DEBUG
is defined:

  CC      drivers/ata/sata_fsl.o
drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’:
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’
drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’:
drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function)
drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once
drivers/ata/sata_fsl.c:459: error: for each function it appears in.)
drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’:
drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function)
make[2]: *** [drivers/ata/sata_fsl.o] Error 1
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

SB700 SATA controller can support 64 bit DMA, the previous commit
badc2341 was added with
careless reference to SB600, which should be modified by this patch.
Signed-off-by: NShane Huang <shane.huang@amd.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

>> Mark Lord wrote:
>>> Tejun, I've added PMP to sata_mv, and am now trying to get it
>>> to work with a Marvell PM attached.

> >>> And the behaviour I see is very bizarre.

>>> After hard+soft resets, the PM signature is found,
>>> and libata interrogates the PM registers.
>>>
>>> It successfully reads register 0, and then register 1.
>>> But all subsequent registers read out (incorrectly) as zeros.
...

This behavior has been confirmed by Marvell with a SATA analyzer.
The Marvell port-multiplier apparently likes to see clean HOB
information when accessing PMP registers.

Since sata_mv uses PIO shadow register access, this doesn't happen
automatically, as it might in a more purely FIS-based driver (eg. ahci).

One way to fix this is to flag these commands with ATA_TFLAG_LBA48,
forcing libata to write out the HOB fields with known (zero) values.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Acked-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.

That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).

So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.

This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.

Original patch is from Mark Lord.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

power_state is scheduled for removal, and libata uses it in write-only
mode. Remove it.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

AHCI needs sorting too but this deals with the old interface
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
  [NETFILTER]: fix ebtable targets return
  [IP_TUNNEL]: Don't limit the number of tunnels with generic name explicitly.
  [NET]: Restore sanity wrt. print_mac().
  [NEIGH]: Fix race between neighbor lookup and table's hash_rnd update.
  [RTNL]: Validate hardware and broadcast address attribute for RTM_NEWLINK
  tg3: ethtool phys_id default
  [BNX2]: Update version to 1.7.4.
  [BNX2]: Disable parallel detect on an HP blade.
  [BNX2]: More 5706S link down workaround.
  ssb: Fix support for PCI devices behind a SSB->PCI bridge
  zd1211rw: fix sparse warnings
  rtl818x: fix sparse warnings
  ssb: Fix pcicore cardbus mode
  ssb: Make the GPIO API reentrancy safe
  ssb: Fix the GPIO API
  ssb: Fix watchdog access for devices without a chipcommon
  ssb: Fix serial console on new bcm47xx devices
  ath5k: Fix build warnings on some 64-bit platforms.
  WDEV, ath5k, don't return int from bool function
  WDEV: ath5k, fix lock imbalance
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: make IOMMU code respect the segment boundary limits
  [SPARC64]: Fix cpu trampoline et al. mismatch warnings.
  [SPARC64]: More sparse warning fixes in process.c
  [SPARC64]: Fix sparse warning wrt. fault_in_user_windows.
  [SPARC64]: Kill show_regs32().
  [SPARC64]: Fix sparse warnings wrt. __show_regs().
  [SPARC64]: Kill show_stackframe{,32}().
  [SPARC64]: Fix sparse warnings wrt. machine_alt_power_off().

This fixes the following compile error caused by commit
3a2d5b70 ("PM: Introduce
PM_EVENT_HIBERNATE callback state")

    CC [M]  drivers/usb/host/u132-hcd.o
  drivers/usb/host/u132-hcd.c: In function ‘u132_suspend’:
  drivers/usb/host/u132-hcd.c:3224: error: expected expression before ‘int’
  drivers/usb/host/u132-hcd.c:3225: error: ‘ports’ undeclared (first use in this function)
  ...
Signed-off-by: NMirco Tischler <mt-ml@gmx.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The function ebt_do_table doesn't take NF_DROP as a verdict from the targets.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the added dev_alloc_name() call to create tunnel device name,
rather than iterate in a hand-made loop with an artificial limit.

Thanks Patrick for noticing this.

[ The way this works is, when the device is actually registered,
  the generic code noticed the '%' in the name and invokes
  dev_alloc_name() to fully resolve the name.  -DaveM ]
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAC_FMT had only one user and we tried to get rid of
that, but this created more problems than it solved.

As a result, this reverts three commits:

235365f3 ("net/8021q/vlan_dev.c: Use
print_mac."), fea5fa87 ("[NET]: Remove
MAC_FMT"), and 8f789c48 ("[NET]:
Elminate spurious print_mac() calls.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The neigh_hash_grow() may update the tbl->hash_rnd value, which 
is used in all tbl->hash callbacks to calculate the hashval.

Two lookup routines may race with this, since they call the 
->hash callback without the tbl->lock held. Since the hash_rnd
is changed with this lock write-locked moving the calls to ->hash
under this lock read-locked closes this gap.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTM_NEWLINK allows for already existing links to be modified. For this
purpose do_setlink() is called which expects address attributes with a
payload length of at least dev->addr_len. This patch adds the necessary
validation for the RTM_NEWLINK case.

The address length for links to be created is not checked for now as the
actual attribute length is used when copying the address to the netdevice
structure. It might make sense to report an error if less than addr_len
bytes are provided but enforcing this might break drivers trying to be
smart with not transmitting all zero addresses.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When asked to blink LEDs the tg3 driver behaves when using:
	ethtool -p ethX
The default value for data is zero, and other drivers interpret this
as blink forever (or at least a really long time).  The tg3 driver
interprets this as blink once.  All drivers should have the same
behaviour.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NOliver Pinter <oliver.pntr@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>