- 23 8月, 2013 1 次提交
-
-
由 Johannes Berg 提交于
mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether the start_sched_scan operation is supported or not, but that will not be correct for all drivers, we're adding scheduled scan to the iwlmvm driver but it depends on firmware support. Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers so that they can control it regardless of implementing the operation. This currently only affects the TI drivers since they're the only ones implementing scheduled scan (in a mac80211 driver.) Acked-by: NLuciano Coelho <luca@coelho.fi> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 22 8月, 2013 1 次提交
-
-
由 Johannes Berg 提交于
Sujith reports that my commit af61a165 ("mac80211: add control port protocol TX control flag") broke ath9k (aggregation). The reason is that I made minstrel_ht use the flag in the TX status path, where it can have been overwritten by the driver. Since we have no more space in info->flags, revert that part of the change for now, until we can reshuffle the flags or so. Reported-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 16 8月, 2013 3 次提交
-
-
由 Johannes Berg 提交于
In order to be able to (securely) keep connections alive after the system was suspended for WoWLAN, we need some additional APIs. We already have API (ieee80211_gtk_rekey_notify) to tell wpa_supplicant about the new replay counter if GTK rekeying was done by the device while the host was asleep, but that's not sufficient. If GTK rekeying wasn't done, we need to tell the host about sequence counters for the GTK (and PTK regardless of rekeying) that was used while asleep, add ieee80211_set_key_rx_seq() for that. If GTK rekeying was done, then we need to be able to disable the old keys (with ieee80211_remove_key()) and allocate the new GTK key(s) in mac80211 (with ieee80211_gtk_rekey_add()). If protocol offload (e.g. ARP) is implemented, then also the TX sequence counter for the PTK must be updated, using the new ieee80211_set_key_tx_seq() function. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Simon Wunderlich 提交于
Channel Switch will later require to generate beacons without setting them immediately. Therefore split the presp generation in an own function. Splitting the original very long function might be a good idea anyway. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johan Almbladh 提交于
This patch decouples the power save processing from the frame decryption by running the decrypt rx handler after sta_process. In the case where the decryption failed for some reason, the stack used to not process the PM and MOREDATA bits for that frame. The stack now always performs power save processing regardless of the decryption result. That means that encrypted data frames and NULLFUNC frames are now handled in the same way regarding power save processing, making the stack more robust. Signed-off-by: NJohan Almbladh <ja@anyfi.net> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 13 8月, 2013 1 次提交
-
-
由 Antonio Quartulli 提交于
In some cases mac80211 will scan before creating an IBSS even if bssid and frequency have been forced by the user. This is not needed and leads only to a delay in the IBSS establishment phase. Immediately create the cell if both bssid and frequency (and fixed_freq is set) have been specified. Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 12 8月, 2013 3 次提交
-
-
由 David Spinadel 提交于
Pass the wdev from cfg80211 on to the driver as the vif if given and it's valid for the driver. Signed-off-by: NDavid Spinadel <david.spinadel@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 David Spinadel 提交于
To allow drivers to implement per-interface testmode operations more easily, pass a wdev pointer if any identification for one was given from userspace. Clean up the code a bit while at it. Signed-off-by: NDavid Spinadel <david.spinadel@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
A lot of drivers check the frame protocol for ETH_P_PAE, for various reasons (like making those more reliable). Add a new flags bitmap to the TX control info and a new flag indicating the control port protocol is in use to let all drivers also apply such logic to other control port protocols, should they be configured. Also use the new flag in the iwlwifi drivers. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 09 8月, 2013 2 次提交
-
-
由 Simon Wunderlich 提交于
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
Allow lowest basic rate to be used for unicast management frame in mesh. Otherwise, the lowest supported rate is used for unicast management frame, such as 1Mbps for 2.4GHz and 6Mbps for 5GHz. Rename the rc_send_low_broadcast to re_send_low_basicrate since now it is also applied to unicast management frame in mesh. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 06 8月, 2013 1 次提交
-
-
由 Johannes Berg 提交于
A few places in the code (mac80211 and iwlmvm) use the same TU_TO_JIFFIES() macro and could use TU_TO_EXP_TIME() that mac80211 has. Make these available to everyone and use them. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 02 8月, 2013 1 次提交
-
-
由 Simon Wunderlich 提交于
The count field in CSA must be decremented with each beacon transmitted. This patch implements the functionality for drivers using ieee80211_beacon_get(). Other drivers must call back manually after reaching count == 0. This patch also contains the handling and finish worker for the channel switch command, and mac80211/chanctx code to allow to change a channel definition of an active channel context. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> [small cleanups, catch identical chandef] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 01 8月, 2013 4 次提交
-
-
由 Johannes Berg 提交于
Add a per-station debugfs file indicating the TIDs (as a bitmap) that the driver has data buffered on. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Karl Beldan 提交于
The radiotap VHT info is 12 bytes (required to be aligned on 2) : u16 known - IEEE80211_RADIOTAP_VHT_KNOWN_* u8 flags - IEEE80211_RADIOTAP_VHT_FLAG_* u8 bandwidth u8 mcs_nss[4] u8 coding u8 group_id u16 partial_aid ATM mac80211 can handle IEEE80211_RADIOTAP_VHT_KNOWN_{GI,BANDWIDTH} and mcs_nss[0] (i.e single user) in simple cases. This is more a placeholder to let sniffers give more clues for VHT, since we don't have yet the proper infrastructure/conventions in mac80211 for complete feedback (e.g consider dynamic BW). Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Antonio Quartulli 提交于
A station which is not authorized has to be purged earlier to give it a chance to re-try to establish an IBSS/RSN session soon. Set the timeout to 10 seconds. Some refactoring has also been done to allow the IBSS submodule to have its own expiring function. Reported-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Fabio Baltieri 提交于
Change mac80211 LED trigger code to use the generic led_trigger_blink_oneshot() API for transmit and receive activity indication. This gives a better feedback to the user, as with the new API each activity event results in a visible blink, while a constant traffic results in a continuous blink at constant rate. Signed-off-by: NFabio Baltieri <fabio.baltieri@gmail.com> [fix LED disabled build error] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 16 7月, 2013 14 次提交
-
-
由 Johannes Berg 提交于
When a driver (like hwsim) uses HW queue control an active monitor vif needs to be used for the queues, make the code do that. Otherwise we'd bail out and drop the frames. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
Set the Forwarding bit in Mesh Capability Info according to dot11MeshForwarding as defined in IEEE 802.11-2012 section 8.4.2.100.8. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Simon Wunderlich 提交于
There is an off-by-one error in the beacon generation for the ibss mode, falsely a rate the extended supported rates which was already added to supported rates, messing up the beacon. This was introduced by commit "mac80211: select and adjust bitrates according to channel mode". Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Simon Wunderlich 提交于
There appear to be two regressions in ibss.c when calling ieee80211_sta_def_wmm_params(): * the second argument should be a rate length, not a rate array. This was introduced by my commit "mac80211: select and adjust bitrates according to channel mode" * the third argument is not initialized (anymore), making further checks within this function useless. Since ieee80211_sta_def_wmm_params() is only used by ibss anyway, remove the function entirely and handle the operating mode decision immediately. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Simon Wunderlich 提交于
This was originally designed to fail when a 40+/40- mode can not be used, but basic modes (such as 5/10/20 MHz) must be handled with an error. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
Use a chandef instead of just the channel for scanning, and enable 5/10 Mhz scanning for IBSS mode. Also reporting is changed to the new inform_bss functions. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
Some regulations (like germany, but also FCC) express their transmission power limit in dBm/MHz or mW/MHz. To cope with that and be on the safe side, reduce the maximum power to half (10 MHz) or quarter (5 MHz) when operating on these reduced bandwidth channels. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
Mandatory rates for 5 and 10 MHz are different from the rates used for 20 MHz in 2.4 GHz mode, as they use OFDM only. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
The various components accessing the bitrates table must use consider the used channel bandwidth to select only available rates or calculate the bitrate correctly. There are some rates in reduced bandwidth modes which can't be represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The standard suggests to round up to the next multiple of 500kbps, just do that in mac80211 as well. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> [make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix] Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
Wireshark already defines radiotap channel flags for 5 and 10 MHz, so just use them in Linux radiotap too. Furthermore, add rx status flags to allow drivers to report when they received data on 5 or 10 MHz channels. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
according to IEEE 802.11-2012 section 18, various timings change when using 5 MHz and 10 MHz. Reflect this by using a "shift" when calculating durations. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
5 and 10 MHz support needs to know the current operating channel width, add the chandef to the rate control API. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Johannes Berg 提交于
When per-chain signal information is available, don't add the antenna field once but instead add a radiotap namespace for each chain containing the chain/antenna number and the signal strength on that chain. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Simon Wunderlich 提交于
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
- 04 7月, 2013 1 次提交
-
-
由 Kees Cook 提交于
For the workqueue creation interfaces that do not expect format strings, make sure they cannot accidently be parsed that way. Additionally, clean up calls made with a single parameter that would be handled as a format string. Many callers are passing potentially dynamic string content, so use "%s" in those cases to avoid any potential accidents. Signed-off-by: NKees Cook <keescook@chromium.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 24 6月, 2013 2 次提交
-
-
由 Thomas Pedersen 提交于
Previously the default mesh STA nonpeer power mode was UNKNOWN (0) make the default mesh STA power mode ACTIVE, to prevent unnecessary frame buffering while peering is not yet complete. Fixes a panic in ath9k_htc when adding stations from userspace, and mcast buffered frames are later released. Thanks to Bob Copeland for his help debugging this. Signed-off-by: NThomas Pedersen <thomas@cozybit.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Thomas Pedersen 提交于
Useful for userspace mesh to authenticate and peer without a station entry, since both steps may fail anyway. Signed-off-by: NThomas Pedersen <thomas@cozybit.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 20 6月, 2013 1 次提交
-
-
由 Johannes Berg 提交于
Doing so will allow us to hold the BSS (not just ref it) over the association process, thus ensuring that it doesn't time out and gets invisible to the user (e.g. in 'iw wlan0 link'.) This also fixes a leak in mac80211 where it doesn't always release the BSS struct properly in all cases where calling this function. This leak was reported by Ben Greear. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 18 6月, 2013 4 次提交
-
-
由 Antonio Quartulli 提交于
This reverts commit 6d810f10 In this way an IBSS station will not use the AUTH messages to trigger a state reinitialisation anymore. The behaviour was racy and was not working properly. It has been introduced to help wpa_supplicant to support IBSS/RSN, however all the logic is now getting moved into wpa_s itself which will also be in charge of handling the AUTH messages thanks to the mgmt frame registration. If userspace does not register for receiving AUTH frames then mac80211 will still reply by itself. At the same time, the auth frame registration counter can be removed since it is not needed anymore. Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com> [remove unused variable] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Simon Wunderlich 提交于
This should make some parts cleaner and is also required for handling 5/10 MHz properly. Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Simon Wunderlich 提交于
This is a collection of minor fixes: * don't allow HT IEs in IBSS for 5/10 MHz * don't allow HT IEs in Mesh for 5/10 MHz * don't downgrade from/to 5 and 10 MHz channels * don't try HT rates for 5 and 10 MHz channels when selecting rates Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Thomas Pedersen 提交于
Instead of updating the mesh beacon immediately when requested (which would require the sdata_lock()), defer it to the mac80211 workqueue. Fixes yet another deadlock on calling sta_info_flush() with the sdata_lock() held from ieee80211_stop_mesh(). We could just drop the sdata_lock() around the mesh_sta_cleanup() call, but this path is also taken from several non-locked error paths. Signed-off-by: NThomas Pedersen <thomas@cozybit.com> [fix comment position] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 13 6月, 2013 1 次提交
-
-
由 Ilan Peer 提交于
Signed-off-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-