I thought this might help track down stuck queues, etc.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.

In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.

Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered.  Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.

In addtion, use the vif type instead of hardware opmode
when dealing with beacons.

Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because the sendbar variable was not reset to zero, the stack would send
Block ACK requests for all subframes following the one that failed, which
could mess up the receiver side block ack window.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes the first TID in the first AC's list is not available for forming
a new aggregate (the BAW might not allow it), however other TIDs may have
data available for sending.
Prevent a slowdown of other TIDs by going through multiple entries until
we've either hit the last one or enough AMPDUs are pending in the hardware
queue.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9285 carrier leakage calibration related workaround on high
temperature is not applicable for AR9271.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k_hw assumes that caldata is valid only for
oper channel. But with ath9k_htc case, the caldata is
passed for all channels on hw_reset though we are not doing
calibration on that channel. So the oper channel's nf history
got cleared to default due to mismatch in channel flags.
This patch also saves some space.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

caldata's channel info is never filled with operating channel
info which is causing the operating channel's noise floor
history buffer is reset to default nf during channel change.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rx error bit parsing was changed to consider PHY errors and various
decryption errors separately. While correct according to the documentation,
this is causing spurious decryption error reports in some situations.

Fix this by restoring the original order of the checks in those places,
where the errors are meant to be mutually exclusive.

If a CRC error is reported, then MIC failure and decryption errors
are irrelevant, and a PHY error is unlikely.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Eeprom read functions are of bool type and not int.
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since baseband hangs are rare, but the hang check function has a high
false positive rate in some situations, we need to add more reliable
indicators.

In AP mode we can use blocked beacon transmissions as an indicator,
they should be rare enough.

In station mode, we can skip the hang check entirely, since a true
hang will trigger beacon loss detection, and mac80211 will rescan,
which leads to a hw reset that will bring the hardware back to life.

To make this more reliable, we need to skip fast channel changes
if the hardware appears to be stuck.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There might be some old stale data left, which could confuse tracking
of pending tx frames.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

txtid->seq_start may not always be up to date, when there is HT non-AMPDU
traffic just before starting an AMPDU session. Relying on txtid->seq_next
is better, since it is also used to generate the sequence numbers for
all QoS data frames.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a tid pointer is passed to ath_tx_send_normal(), it increases the
starting sequence number for the next AMPDU action frame, which should
only be done if the sequence number assignment is fresh. In this case
it is clearly not.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For USB devices, reading the EEPROM data can be offloaded
to the target. Use multiple register reads to take advantage
of this feature to reduce initialization time.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This would decrease latency in reading bulk registers.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.

Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

USB devices do not require the chip test routine.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To inject a packet in monitor mode, a dummy station has
to be associated with the monitor interface in the target.
Failing to do this would result in a firmware crash on the device.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing
the result in "ee_mode" which is an unsigned char.  This breaks the
error handling.  This patch makes "ee_mode" an int.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove some obvious looking dead code and rename few functions
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 0ce3bcfc.

Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period

Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And add the copyright/license header.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().

This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.

Cc: stable <stable@kernel.org>
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch revamps some common code-paths which are
shared between (re-)initialization and suspend/resume
subroutines. It also adds some helpful comments
about quirks and associated difficulties.

It's quite big, but it should fix #25382:
<https://bugzilla.kernel.org/show_bug.cgi?id=25382>

And hopefully the code is robust enough to deal with
all possible suspend/resume scenarios without requiring
the user to do any sort of manual and possibly
dangerous work.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By removing two "safety" msleeps (and an echo nop), the
channel change delay is effectively halved. Previously,
the delay could be as long as 260 ms and the device
could not go off-channel without risking to miss the
next DTIM beacon [interval ~307 ms].
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a forgotten bail-out path.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_reset is called from process context and takes the cc_lock
with plain spin_lock(), but cc_lock can also be taken from tasklets
in softirq context.  Thus we need to at least use spin_lock_bh.

This fixes the following lockdep warning:

[   19.967874] sky2 0000:01:00.0: eth0: enabling interface
[   19.982761] ieee80211 phy0: device now idle
[   20.904809] NET: Registered protocol family 17
[   21.243857] ieee80211 phy0: device no longer idle - scanning
[   21.404343]
[   21.404346] =================================
[   21.404450] [ INFO: inconsistent lock state ]
[   21.404518] 2.6.37-rc7-wl+ #242
[   21.404582] ---------------------------------
[   21.404650] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[   21.404721] kworker/u:4/982 [HC0[0]:SC1[3]:HE1:SE0] takes:
[   21.404792]  (&(&common->cc_lock)->rlock){+.?...}, at: [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011] {SOFTIRQ-ON-W} state was registered at:
[   21.405011]   [<c105cadd>] __lock_acquire+0x62f/0x13c1
[   21.405011]   [<c105d944>] lock_acquire+0xd5/0xf1
[   21.405011]   [<c12c978d>] _raw_spin_lock+0x45/0x72
[   21.405011]   [<f8111533>] ath5k_reset+0x2c0/0x349 [ath5k]
[   21.405011]   [<f8111a7a>] ath5k_start+0xb8/0x139 [ath5k]
[   21.405011]   [<f849c714>] ieee80211_do_open+0x13f/0x819 [mac80211]
[   21.405011]   [<f849ce51>] ieee80211_open+0x63/0x66 [mac80211]
[   21.405011]   [<c1258b2e>] __dev_open+0x8d/0xb6
[   21.405011]   [<c1255c64>] __dev_change_flags+0x9d/0x114
[   21.405011]   [<c1258a75>] dev_change_flags+0x18/0x44
[   21.405011]   [<c1262990>] do_setlink+0x23f/0x521
[   21.405011]   [<c1262d58>] rtnl_setlink+0xe6/0xea
[   21.405011]   [<c126347c>] rtnetlink_rcv_msg+0x18a/0x1a0
[   21.405011]   [<c126d5f0>] netlink_rcv_skb+0x35/0x7b
[   21.405011]   [<c12632eb>] rtnetlink_rcv+0x20/0x27
[   21.405011]   [<c126d370>] netlink_unicast+0x1bb/0x21e
[   21.405011]   [<c126db21>] netlink_sendmsg+0x23b/0x288
[   21.405011]   [<c124823c>] sock_sendmsg+0xac/0xc4
[   21.405011]   [<c1248680>] sys_sendmsg+0x152/0x1a2
[   21.405011]   [<c1249b0d>] sys_socketcall+0x214/0x275
[   21.405011]   [<c10029d0>] sysenter_do_call+0x12/0x36
[   21.405011] irq event stamp: 138032
[   21.405011] hardirqs last  enabled at (138032): [<c12ca252>] _raw_spin_unlock_irqrestore+0x3b/0x5e
[   21.405011] hardirqs last disabled at (138031): [<c12c98cc>] _raw_spin_lock_irqsave+0x18/0x7e
[   21.405011] softirqs last  enabled at (138024): [<f84a570e>] ieee80211_tx_skb+0x47/0x49 [mac80211]
[   21.405011] softirqs last disabled at (138027): [<c100452b>] do_softirq+0x63/0xb4
[   21.405011]
[   21.405011] other info that might help us debug this:
[   21.405011] 3 locks held by kworker/u:4/982:
[   21.405011]  #0:  (name){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b
[   21.405011]  #1:  ((&(&local->scan_work)->work)){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b
[   21.405011]  #2:  (&local->mtx){+.+.+.}, at: [<f84920fb>] ieee80211_scan_work+0x32/0x4a4 [mac80211]
[   21.405011]
[   21.405011] stack backtrace:
[   21.405011] Pid: 982, comm: kworker/u:4 Not tainted 2.6.37-rc7-wl+ #242
[   21.405011] Call Trace:
[   21.405011]  [<c12c6e68>] ? printk+0x1d/0x25
[   21.405011]  [<c105a742>] print_usage_bug+0x181/0x18b
[   21.405011]  [<c105b196>] ? check_usage_forwards+0x0/0xb6
[   21.405011]  [<c105a9ec>] mark_lock+0x2a0/0x4aa
[   21.405011]  [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd
[   21.405011]  [<c105ca68>] __lock_acquire+0x5ba/0x13c1
[   21.405011]  [<c1059eed>] ? trace_hardirqs_off_caller+0x18/0x8d
[   21.405011]  [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd
[   21.405011]  [<c1050411>] ? local_clock+0x2c/0x4f
[   21.405011]  [<c1059e00>] ? save_trace+0x2/0xa0
[   21.405011]  [<c105ac39>] ? mark_held_locks+0x43/0x5b
[   21.405011]  [<c12ca252>] ? _raw_spin_unlock_irqrestore+0x3b/0x5e
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c105d944>] lock_acquire+0xd5/0xf1
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c12c9b1a>] _raw_spin_lock_bh+0x4a/0x77
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c105ac39>] ? mark_held_locks+0x43/0x5b
[   21.405011]  [<f8113496>] ath5k_tasklet_ani+0x1d/0x27 [ath5k]
[   21.405011]  [<c1037304>] tasklet_action+0x96/0x137
[   21.405011]  [<c10379b5>] __do_softirq+0xde/0x1c3
[   21.405011]  [<c10b0cef>] ? arch_get_unmapped_area_topdown+0x3b/0x127
[   21.405011]  [<c10378d7>] ? __do_softirq+0x0/0x1c3
[   21.405011]  <IRQ>  [<c1036dee>] ? irq_exit+0x3d/0x49
[   21.405011]  [<c1003b4f>] ? do_IRQ+0x98/0xac
[   21.405011]  [<c1002eee>] ? common_interrupt+0x2e/0x34
[   21.405011]  [<c103007b>] ? sys_unshare+0x57/0x226
[   21.405011]  [<c1047fee>] ? queue_delayed_work+0x1/0x27
[   21.405011]  [<f84a83a0>] ? ieee80211_queue_delayed_work+0x2e/0x33 [mac80211]
[   21.405011]  [<f8492528>] ? ieee80211_scan_work+0x45f/0x4a4 [mac80211]
[   21.405011]  [<c104620e>] ? process_one_work+0x26e/0x41b
[   21.405011]  [<c1046158>] ? process_one_work+0x1b8/0x41b
[   21.405011]  [<f84920c9>] ? ieee80211_scan_work+0x0/0x4a4 [mac80211]
[   21.405011]  [<c10466b6>] ? worker_thread+0x18a/0x2a5
[   21.405011]  [<c12ca25e>] ? _raw_spin_unlock_irqrestore+0x47/0x5e
[   21.405011]  [<c104652c>] ? worker_thread+0x0/0x2a5
[   21.405011]  [<c104abe7>] ? kthread+0x67/0x6c
[   21.405011]  [<c104ab80>] ? kthread+0x0/0x6c
[   21.405011]  [<c1002efa>] ? kernel_thread_helper+0x6/0x10
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>