Enable configs for following modules:
 * SFC (Sampling Frequency Converter)
 * MVC (Master Volume Control)
 * AMX (Audio Multiplexer)
 * ADX (Audio Demultiplexer)
 * Mixer

These configs are used on Tegra186 and later SoCs as well.
Signed-off-by: NSameer Pujar <spujar@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The MSM8996 supports CPU frequency scaling, so enable the clock driver
for this.
Acked-by: NKonrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210804193042.1155398-1-bjorn.andersson@linaro.orgSigned-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>

96Boards RB3 has a USB XHCI PCI Renesas host controller. This controller
requires firmware to be loaded on its ROM/RAM, so enable the module
CONFIG_USB_XHCI_PCI_RENESAS. This depends on CONFIG_USB_XHCI_PCI so
enable that as well.
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210615081749.3210344-1-vkoul@kernel.orgSigned-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>

Enable Visconti's GPIO in the ARM64 defconfig.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>

Enable Visconti's PWM in the ARM64 defconfig as a module.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>

Add modules with drivers needed for DragonBoard410c board
(arch/arm64/boot/dts/qcom/apq8016-sbc.dts).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210528140625.6972-1-m.szyprowski@samsung.comSigned-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>

Enable the Renesas RZ/G2L SoC variants in the ARM64 defconfig.
Signed-off-by: NLad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: NBiju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-6-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Enable the Exynos UFS controller and PHY configs. They need to be
buildin to ensure UFS devices gets detected on exynos7 and its
variant boards.
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210531170057.7730-1-alim.akhtar@samsung.comSigned-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

Enable the interconnect for SM8350 as a module
Reviewed-by: NBhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210510070725.3839459-1-vkoul@kernel.orgSigned-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>

There is a clock driver that's needed when using an external
USB reference clock called usb2_clksel.
Enable it in the defconfig.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-3-aford173@gmail.comSigned-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Most Layerscape SoCs support ECC error reporting for the memory
controller. Enable the corresponding module. In particular, this will
enable EDAC support on the Kontron sl28 board which comes with ECC
memory.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable the MMC_MTK option necessary to boot Mediatek boards from the
mmc. Booting from the mmc is the common method used for a bunch of
boards, specially Chromebooks, to boot from. Hence this driver is
built-in.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210423075250.2616275-1-enric.balletbo@collabora.comSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

Commit 'fbbe3830 ("arm64: defconfig: Allow mt8173-based boards to boot
from usb")' added the MTK_PMIC_WRAP config built-in. It needs to be
built-in in order to be able to boot from USB or the MMC without needing
a ramdisk, but that symbol was already defined as a module so now we are
getting the following warning:

  arch/arm64/configs/defconfig:996:warning: override: reassigning to symbol MTK_PMIC_WRAP

Remove the MTK_PMIC_WRAP=m from the defconfig to remove the error.

Fixes: fbbe3830 ("arm64: defconfig: Allow mt8173-based boards to boot from usb")
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210423075201.2616023-1-enric.balletbo@collabora.comSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

This driver is used by the Nitrogen8 SBC.
Signed-off-by: NAdrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This adds a Kconfig option to toggle support for Apple ARM SoCs.
At this time this targets the M1 and later "Apple Silicon" Mac SoCs.
Signed-off-by: NHector Martin <marcan@marcan.st>

There are some Mediatek based Chromebooks supported in the kernel. Enable the
required config options to have the panel display working on both devices.
This was tested on the ACER Chromebook R13 (MT8173) and the Lenovo
Ideapad Duet (MT8183), but should also enable display support for similar
devices.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NHsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210331090659.4169966-2-enric.balletbo@collabora.comSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

Enable the option necessary to boot mt8173-based boards to boot from
usb devices, like its phy and the regulators needed to have proper
support.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NHsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210331090659.4169966-1-enric.balletbo@collabora.comSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

This driver is used on Layerscape SoCs to wake up the system from
standby. It works in conjunction with the RCPM driver. The latter is
only available as a builtin.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

On the i.MX8MP EVK board there is a RTL8211 EThernet PHY and
a typical use case is to boot via NFS. In this case the Ethernet
PHY driver needs to be built-in, so select the driver as built-in
by default.
Reported-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Tested-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable in defconfig two Intel ARM64 architectures: the eASIC N5X SoCFPGA
and Keem Bay SoC.  This allows compile coverage when building default
config.

For the N5X (and Agilex) enable also DesignWare SPI controller in MMIO.
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

Agilex, N5X and Stratix 10 share all quite similar arm64 hard cores and
SoC-part.  Up to a point that N5X uses the same DTSI as Agilex.  From
the Linux kernel point of view these are flavors of the same
architecture so there is no need for three top-level arm64
architectures.  Simplify this by merging all three architectures into
ARCH_INTEL_SOCFPGA and dropping the other ARCH* arm64 Kconfig entries.

The side effect is that the INTEL_STRATIX10_SERVICE will now be
available for both 32-bit and 64-bit Intel SoCFPGA, even though it is
used only for 64-bit.
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>

Enable PCI_IMX6 to get PCI support for imx8mq boards like imx8mq-evk,
imx8mq-kontron-pitx-imx8m and imx8mq-zii-ultra.

The driver only has build-in support and cannot be compiled as module.
Signed-off-by: NHeiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable the Hantro decoder driver so it can be enabled by
default on i.MX8M and Rockchip platforms.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NGuido Günther <agx@sigxcpu.org>
Signed-off-by: NMartin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

We've had DEBUG_INFO enabled for arm64 defconfigs since the initial
commit.  This is probably not that frequently used but substantially
inflates the size of the build tree and amount of I/O needed during the
build.  This was causing issues with storage usage in some automated CI
environments which don't expect defconfigs to be quite this big, and
generally increases the resource consumption for both them and people
doing local builds.  The main use case for the debug info is decoding
things with scripts/faddr2line but that doesn't need the full
DEBUG_INFO, DEBUG_INFO_REDUCED is enough for it, so enable that by
default.

Without this patch my build tree is 6.8G, with it the size drops to 2G
(smaller than the 6.4G for allmodconfig!).
Suggested-by: NCatalin Marinas <catalin.marinas@arm.com>
Reported-by: NGuillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NKevin Hilman <khilman@baylibre.com>
Acked-by: NWill Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210304174407.17537-1-broonie@kernel.orgSigned-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Except MX8QM pinctrl driver is missing, all other necessary drivers
for a booting are reused from MX8QXP which are already enabled
in defconfig.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This driver is used by the Nitrogen8m Mini SBC.
Signed-off-by: NAdrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This is needed to model the mic input mux on the Librem 5 devkit.
Signed-off-by: NGuido Günther <agx@sigxcpu.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This is needed to make DRAM frequency scaling via devfreq as used
on the Librem 5 and Librem 5 Devkit.

With the interconnect support enabled we now need imx devfreq on top
to make this work.
Signed-off-by: NGuido Günther <agx@sigxcpu.org>
Signed-off-by: NMartin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable the Qualcomm SM8350 TLMM pinctrl and GCC clock drivers. They need
to be builtin to ensure that the UART is allowed to probe before user
space needs a console.
Reviewed-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210306021021.1173860-1-bjorn.andersson@linaro.orgSigned-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>

Enable the RT5659 audio codec driver. Jetson AGX Xavier has RT5658 codec
which is compatible with this driver. This enables user to test external
audio.
Signed-off-by: NSameer Pujar <spujar@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Bard Liao <bardliao@realtek.com>

Support DEVAPC on MediaTek platforms by enabling CONFIG_MTK_DEVAPC.
Signed-off-by: NNeal Liu <neal.liu@mediatek.com>
Link: https://lore.kernel.org/r/1608713092-26952-3-git-send-email-neal.liu@mediatek.comSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

Support pwrap on Mediatek MT6779 platform by enabling CONFIG_MTK_PMIC_WRAP.
Signed-off-by: NArgus Lin <argus.lin@mediatek.com>
Link: https://lore.kernel.org/r/1609747703-27207-3-git-send-email-argus.lin@mediatek.comSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

This driver is mandatory for the nitrogen8m mini board
when booting from the sdcard slot.
Signed-off-by: NAdrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The haptic motor for the Librem 5 uses this.
Signed-off-by: NGuido Günther <agx@sigxcpu.org>
Signed-off-by: NMartin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

It'll be used by the RPi4 family of boards to access its bootloader
configuration.
Signed-off-by: NNicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210112142342.7290-1-nsaenzjulienne@suse.de

This commit enables Tegra audio graph card driver which is based on
the generic audio-graph card driver. This is intended to be used
on platforms based on Tegra210 and later chips.
Signed-off-by: NSameer Pujar <spujar@nvidia.com>
Reviewed-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Enable the Tegra SoC Thermal driver that is used by Tegra132 and
Tegra210 platforms to be built as a module by default for ARM64 builds.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The i2c-hid driver has been split in two.  Let's enable both halves.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Acked-by: NWill Deacon <will@kernel.org>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>

Enable support for the QuadPHY on the Kontron K-Box A-230-LS. Enable
the driver as a module.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

With [1] integrated and all users of the config symbols removed, we
can safely remove the options from defconfig.

[1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20201026170624.24241-1-nm@ti.com/Signed-off-by: NNishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210107132228.6577-1-nm@ti.com'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>