The pca953x driver supports tca6424 (24-bit) and pca9505 (40-bit)
devices. They were the only supported devices not mentioned in the
Kconfig help.
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Acked-by: NGraeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

which is already found in the common header for adp5588
Signed-off-by: NJean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

As discussed here: http://ez.analog.com/message/35852,
the 5587 revC and 5588 revB spec sheets contain a mistake
in the GPIO_DAT_STATx register description.

According to R.Shnell at ADI, as well as my own
observations, it should read:
"GPIO data status (shows GPIO state when read for inputs)".

This commit changes the get value function accordingly.
Signed-off-by: NJean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

gpio_to_desc() must die. Replace one of its usage by the
newly-introduced gpiochip_get_desc() function.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some drivers dealing with a gpio_chip might need to act on its
descriptors directly; one example is pinctrl drivers that need to lock a
GPIO for being used as IRQ using gpiod_lock_as_irq().

This patch exports a gpiochip_get_desc() function that returns the
GPIO descriptor at the requested index. It also sweeps the
gpio_to_chip() function out of the consumer interface since any holder
of a gpio_chip reference can manipulate its GPIOs way beyond what a
consumer should be allowed to do.

As a result, gpio_chip is not visible anymore to simple GPIO consumers.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NJean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NRahul Bedarkar <rahulbedarkar89@gmail.com>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

On currently supported SoCs, the GPIO block used on Marvell EBU SoCs
is always connected to the Marvell MPIC. However, we are going to
introduce the support for newer Marvell EBU SoCs that use the
Cortex-A9 core, and therefore use the GIC as their main interrupt
controller, to which the GPIO block controlled by the gpio-mvebu
driver is connected.

The GIC interrupt controller driver uses the fasteoi flow handler. In
order to ensure that the eoi hook of the GIC driver gets called, the
GPIO driver should call chained_irq_enter() and chained_irq_exit() in
its handler. Without this, the first GPIO interrupt locks up the
system because it doesn't get acked at the GIC level.

This change is similar to for example commit
0d978eb7 ("gpio: davinci: use
chained_irq_enter/chained_irq_exit API").
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch allows GPIO driver to cache GPIO_LVL output registers. The aim is to
support chipsets on which GPIO_LVL value can't be read for output pins.

Caching output levels implies the first output values reading as 0. The driver
so can't be aware of set values GPIOs by bootloader or BIOS.
Signed-off-by: NVincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch introduces regs and reglen pointers which allow a chipset to have
register addresses differing from ICH ones.
Signed-off-by: NVincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch allows gpio_ich driver to be aware of non blink capable chipsets.
Signed-off-by: NVincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The documentation was not clear about whether
gpio_direction_output should take a logical value or the physical
level on the output line, i.e. whether the ACTIVE_LOW status
would be taken into account.

This converts gpiod_direction_output to use the logical level
and adds a new gpiod_direction_output_raw for the raw value.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The generic GPIO would return 0 for low generic GPIO, and
something != 0 for high GPIO. Let's make this sane by clamping
the returned value to [0,1].
Reported-by: NEvgeny Boger <boger@contactless.ru>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add missing .owner of struct gpio_chip. This prevents the
module from being removed from underneath its users.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

commit f1f70479 "gpio: pl061: support irqdomain" drops the support of
irq generic chip and use irqdomain instead. Thus fixes the dependency by
selecting IRQ_DOMAIN rather than GENERIC_IRQ_CHIP.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When registering more than one platform device, it is
useful to set the gpio chip label in the platform data.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch removes some inconsistencies caused by the use of "int gpio"
in some parts of the code and "unsigned gpio" in others.
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

PTR_RET is deprecated. Use PTR_ERR_OR_ZERO instead. While at it
also include missing err.h header.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Rather than unlock/re-lock for every write access, unlock a GPIO when
it is requested and re-lock it when it is freed. As a result, the GPIO
helper functions no longer have to deal with unlocking and re-locking
the register.

In addition, only unlock a specific GPIO rather than unlocking the
entire GPIO bank as before.
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The GPIO_CONTROL macro returns the control register offset when given a
GPIO number.

Update the argument name in the macro to reflect that it takes in a
GPIO number and not a bank.
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is a simple cleanup on gpio-intel-mid.c's header comments.
Signed-off-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Drop the " gpio" suffix after the pl061 irq_chip name:
this is only confusing: an irqchip name should be a single,
short, simple string that looks nice in /proc/interrupts.

Drop the nameing of each individual IRQ to "pl061" - I
think this naming function is for naming the IRQ line,
not for boilerplating them all with the name of the
parent controller, which is already known from the
.name field of the irq_chip.

Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Refactor this function so that I can understand it, do one
big read/modify/write operation and have the bitmask in a
variable instead of recalculating it every time it's needed.

Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.

Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the PL061 driver print proper error messages
when probe fails, and also tell us when the chip is finally
registered.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'lp3943_gpio_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.

* Application note: how to configure LP3943 as a GPIO expander
  http://www.ti.com/lit/an/snva287a/snva287a.pdf

* Supported GPIO controller operations
  request, free, direction_input, direction_output, get and set

* GPIO direction register not supported
  LP3943 doesn't have the GPIO direction register. It only provides input and
  output status registers.
  So, private data for the direction should be handled manually.
  This variable is updated whenever the direction is changed and
  used in 'get' operation.

* Pin assignment
  A driver data, 'pin_used' is checked when a GPIO is requested.
  If the GPIO is already assigned, then returns as failure.
  If the GPIO is available, 'pin_used' is set.
  When the GPIO is not used anymore, then it is cleared.
  It is defined as unsigned long type for atomic bit operation APIs,
  but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: NMilo Kim <milo.kim@ti.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NSeongJae Park <sj38.park@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The MCP drivers fails to compile on trial builds due to missing
Kconfig dependency on OF_GPIO. Fix it.

Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds interrupt functionality for i2c chips to the driver.
They can act as a interrupt-controller and generate interrupts, if
the inputs change.
This is tested with a mcp23017 chip on an arm based platform.

v3:
- be a bit more clear that the irq functionality is also available
  on spi versions of the chips, but the linux driver does not support
  this yet

v2:
- some more word about irq-mirror property in binding doc
- use of_read_bool instead of of_find_property for
  "interrupt-contrller" and "irq-mirror"
- cache the "interrupt-controller" for remove function
- do set the irq-mirror bit only if device is marked as
  interrupt-controller
- do create the irq mapping and setup of irq_desc of all possible
  interrupts in probe path instead of in gpio_to_irq
- mark gpios as in use as interrupts in irq in irq_startup and
  unlock it in irq_shutdown
- rename virq to child_irq
- remove dev argument from mcp23s08_irq_setup function
- move gpiochip_add before mcp23s08_irq_setup in probe path
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

gpio-samsung.h header file introduced by commit 93177be0910c
("ARM: S3C[24|64]xx: move includes back under <mach/> scope")
is required only by S3C[24|64]xx machines. Include them conditionally
to avoid the following build errors for other machine configurations.
drivers/gpio/gpio-samsung.c:35:31: fatal error: mach/gpio-samsung.h: No such file or directory
arch/arm/plat-samsung/pm-gpio.c:22:31: fatal error: mach/gpio-samsung.h: No such file or directory
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It would be convenient to normalize the return value for gpio_get.

I have checked mach-mmp / mach-pxa / plat-pxa / plat-orion / mach-orion5x.
It's OK for all of them to change this function to return 0 and 1.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When refactoring and breaking out the includes for the
machine-specific GPIO configuration, two files were created
in <linux/platform_data/gpio-samsung-s3c[24|64]xx.h>, but as
that namespace shall be used for defining data exchanged
between machines and drivers, using it for these broad macros
and config settings is wrong.

Move the headers back into the machine-local
<mach/gpio-samsung.h> file and think about the next step.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that all users of acpi_gpio.h have been moved to use either the GPIO
descriptor interface or to the internal gpiolib.h we can get rid of
acpi_gpio.h entirely.

Once this is done the only interface to get GPIOs to drivers enumerated
from ACPI namespace is the descriptor based interface.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.

We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.

Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since request_muxed_region() is used to synchronize access on the
Super-I/O controller, then the can_sleep attribute must be set for
the f7188x GPIO chips.
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The contents of this header file are not referenced in the driver.
Remove its inclusion.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Prevent build failure when the selected variant does not support GPIO32.
Acked-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This helps increasing build testing coverage.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is no reason to keep the OF data if the driver was compiled
without DT support.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'tb10x_gpio_dt_ids' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>