The stats structure for the VEB switch statistics is reset periodically,
but the tc_stats are not reset at the same time.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Upcoming FW increment API version to 1.9 due to Extend PHY access AQ
command support. SW is ready for that support as well.
Signed-off-by: NPiotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Function check_recovery_mode had wrong if statement.
Now we check proper FWS1B register values, which are responsible for
the recovery mode. Recovery mode has 4 values for x710 and 2 for x722.
That's why we need 6 different flags which are defined in the code.
Now in the if statement, we recognize type of mac address
and register value.
Without those changes driver could show wrong state.
Signed-off-by: NAdrian Podlawski <adrian.podlawski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds "drop mode" parameter to set mac config AQ command.
This bit controls the behavior when a no-drop packet is blocking a TC
queue.
0 – The PF driver is notified.
1 – The blocking packet is dropped and then the PF driver is notified.
Signed-off-by: NSylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes following error reported by cppcheck:
(error) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: NBeilei Xing <beilei.xing@intel.com>
Signed-off-by: NFerruh Yigit <ferruh.yigit@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When i40e_configure_tx_ring(vsi->tx_rings[i]) returns an error, we should
exit from i40e_vsi_configure_tx and return the error, instead of continuing
to check whether xdp is enable, and configure the xdp transmit ring.
Signed-off-by: Nhuhai <huhai@kylinos.cn>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to the ixgbe issue fixed in:
655c9141 ("ixgbe: Check DDM existence in transceiver before access)

i40e has the same issue when reading eeprom from SFP's module that comply
with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM)
interface described in it. The existence of such area is specified by bit
6 of byte 92, set to 1 if implemented.

Without this patch, due to not checking this bit i40e fails to read SFP
module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
Signed-off-by: N"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both
have giant structure on the stack, which makes each one use stack frames
larger than 500 bytes.

As clang decides one function into the other, we get a warning for
exceeding the frame size limit on 32-bit architectures:

drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=]

When building with gcc, the inlining does not happen, but i40e_set_fc()
calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the
kernel stack just as much.

The parts that actually use large stacks don't overlap, so make sure
each one is a separate function, and mark them as noinline_for_stack to
prevent the compilers from combining them again.

Fixes: 0a862b43 ("i40e/i40evf: Add module_types and update_link_info")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes unicast log when VF is leaving multicast mode.
Added check of vf->vf_states &
I40E_VF_STATE_MC_PROMISC/I40E_VF_STATE_UC_PROMISC.
Without this commit, leaving multicast mode logs "unset unicast"
in dmsg.
Signed-off-by: NCzeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to i40e_get_ethtool_stats, add a goto to verify that the data
pointer for the strings lines up with the expected stats count. This
helps ensure that bugs are not introduced when adding stats.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add log when PF is entering and leaving allmulti mode. The
change of PF state is visible in dmesg now. Without this commit,
entering and leaving allmulti mode is not logged in dmesg.
Signed-off-by: NCzeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Updates visual effect for advertised mode after setting desired mode.
The mode appears in advertised FEC mode correctly, when ethtool
interface command is called. Without this commit advertised FEC
is displayed regardless of the settings as "None BaseR RS".
Signed-off-by: NCzeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Found a code comment that needed TLC to correct their formatting.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

Commit d3d657a9 ("i40e: update VFs of link state after
GET_VF_RESOURCES") modified the PF driver to notify a VF of
its link status immediately after it requests resources.

This was intended to fix reporting on VF drivers, so that they would
properly report link status.

However, some older VF drivers do not respond well to receiving a link
up notification before queues are enabled. This can cause their state
machine to think that it is safe to send traffic. This results in a Tx
hang on the VF.

More recent versions of the old i40evf and all versions of iavf are
resilient to these early link status messages. However, if a VM happens
to run an older version of the VF driver, this can be problematic.

Record whether the PF has actually enabled queues for the VF. When
reporting link status, always report link down if the queues aren't
enabled. In this way, the VF driver will never receive a link up
notification until after its queues are enabled.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add logging for disable-fw-lldp flag by ethtool. Added check
for I40E_FLAG_DISABLE_FW_LLDP and logging state in dmesg.
Without this commit there was no clear statement in dmesg
about FW LLDP state in dmesg.
Signed-off-by: NSlawomir Laba <slawomirx.laba@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes missing call of i40e_update_veb_stats() in function
i40e_get_ethtool_stats() to update stats data of VEB and VEB TC
counters before they are written into ethtool buffer.
Before the patch ethtool counters may fell behind interface counters.
Signed-off-by: NDmitrii Golovanov <dmitrii.golovanov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And any other existing fields in this structure that refer to tc.
Specifically:

* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.

This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.

Remove tc_block_offload alias.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.

This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.

This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.

This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.

There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables macvlan offloads for i40e. The idea is to use
channels as macvlan interfaces. The channels are VSIs of
type VMDQ. When the first macvlan is created, the maximum number of
channels possible are created. From then on, as a macvlan interface
is created, a macvlan filter is added to these already created
channels (VSIs).

This patch utilizes subordinate device traffic classes to make queue
groups(channels) available for an upper device like a macvlan.

Steps to configure macvlan offloads:
1. ethtool -K ethx l2-fwd-offload on
2. ip link add link ethx name macvlan1 type macvlan
3. ip addr add <address> dev macvlan1
4. ip link set macvlan1 up
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some drivers want to access the data transmitted in order to implement
acceleration features of the NICs. It is also useful in AF_XDP TX flow.

Change the xsk_umem_consume_tx API to return the whole xdp_desc, that
contains the data pointer, length and DMA address, instead of only the
latter two. Adapt the implementation of i40e and ixgbe to this change.
Signed-off-by: NMaxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: NBjörn Töpel <bjorn.topel@intel.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct virtchnl_iwarp_qvlist_info {
	...
        struct virtchnl_iwarp_qv_info qv_info[1];
};

size = sizeof(struct virtchnl_iwarp_qvlist_info) + (sizeof(struct virtchnl_iwarp_qv_info) * count;
instance = kzalloc(size, GFP_KERNEL);

and

struct virtchnl_vf_resource {
	...
        struct virtchnl_vsi_resource vsi_res[1];
};

size = sizeof(struct virtchnl_vf_resource) + sizeof(struct virtchnl_vsi_resource) * count;
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, qv_info, count), GFP_KERNEL);

and

instance = kzalloc(struct_size(instance, vsi_res, count), GFP_KERNEL);

Notice that, in the first case above, variable size is not necessary, hence it
is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: N"Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It was found that the string that prints our copyright was
not up to date.  Updating to reflect our copyright.
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changing descriptor count via 'ethtool -G' is not persistent across resets.
When PF reset occurs, we roll back to the default value of vsi->num_desc,
which is used then in i40e_alloc_rings to set descriptor count. XDP does a
PF reset so when user has changed the descriptor count and load XDP
program, the default count will be back there.

To fix this:
  * introduce new VSI members - num_tx_desc and num_rx_desc in favour of
    num_desc
  * set them in i40e_set_ringparam to user's values
  * set them to default values in i40e_set_num_rings_in_vsi only when they
    don't have previous values
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes reading f/w LLDP agent status at DCB init time.
It's done by removing direct NVM reading in i40e_update_dcb_config()
and checking whether f/w LLDP agent is disabled via
I40E_FLAG_DISABLE_FW_LLDP flag in i40e_init_pf_dcb(). The function
i40e_update_dcb_config() in i40e_main.c is a temporary solution which
will be later renamed to i40e_init_dcb() in the i40e_dcb module. Also
logging was extended to make visible if f/w LLDP agent is running or not
and always log a message when DCB was not initialized. Without this
patch for new f/w versions f/w LLDP agent status was always read
from NVM as disabled and DCB initialization failed without
clear reason in logs.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Generate log entry when TC0 is created or deleted.
Log entry is generated during main VSI setup.
Before there was no log info about adding or deleting TC0.
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix for missing "Supported link modes" and "Advertised link modes"
info in ethtool after changed speed on X722 devices with BASE-T PHY
with FW API version >= 1.7.
The same FW API version on X710 and X722 does not mean the same
feature set so the change was needed as mac type of the device
should also be checked instead of FW API version only.
Signed-off-by: NMartyna Szapar <martyna.szapar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes 'NIC Link is Up, Unknown bps' message in dmesg
for 2.5Gb/5Gb speeds. This problem is fixed by adding constants
for VIRTCHNL_LINK_SPEED_2_5GB and VIRTCHNL_LINK_SPEED_5GB cases
in the i40e_virtchnl_link_speed() function.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/ethernet/intel/i40e/i40e_xsk.c: In function ‘i40e_run_xdp_zc’:
drivers/net/ethernet/intel/i40e/i40e_xsk.c:217:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
   bpf_warn_invalid_xdp_action(act);
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/i40e/i40e_xsk.c:218:2: note: here
  case XDP_ABORTED:
  ^~~~
Signed-off-by: N"Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver updated pf->flags before calling i40e_aq_start_lldp().
This patch moved down updating pf->flags down so flags will be
updated only in case of successful i40e_aq_start_lldp() call.
Also was introduced is_reset_needed local flag to avoid unnecessary h/w
reset in case 40e_aq_start_lldp() didn't change lldp state.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The tx_errors statistic was being calculated twice in
i40e_update_eth_stats.

This appears to be as of commit 201db2898f2c ("i40e: add missing VSI
statistics", 2014-03-25).

Remove the extra i40e_stat_update32 call for GLV_TEPC.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the problem with a kernel panic occurring when trying
to bind the i40e driver to a non-i40e port. The problem is fixed by
checking if the BAR size in the device is large enough by reading the
highest register.
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver did not check response on LLDP flag change and always returned
SUCCESS.

This patch now checks for an error and returns an error code and has
additional information in the log.
Signed-off-by: NPiotr Marczak <piotr.marczak@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change some data to unsigned int instead of integer when we compare.

Check LUT values in VIRTCHNL_OP_CONFIG_RSS_LUT handler.

Also enhance error/warning messages to print the real values of
I40E_MAX_VF_QUEUES, I40E_MAX_VF_VSI and I40E_DEFAULT_QUEUES_PER_VF
instead of plain text.

Refactor code to comply with 'check first then assign' policy.

Remove duplicate checks for VIRTCHNL_OP_CONFIG_RSS_KEY and
VIRTCHNL_OP_CONFIG_RSS_LUT opcodes in i40e_vc_process_vf_msg(). We have
the very same checks inside the handlers already.
Signed-off-by: NSergey Nemov <sergey.nemov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it possible to log only AQ descriptors, without the
entire AQ message buffers being dumped too. It should greatly reduce
kernel log size in cases where a full AQ dump is not needed.
Selection is made by setting flags in hw->debug_mask.

Additionally, some debug messages that preceded an AQ dump have been
moved to I40E_DEBUG_AQ_COMMAND class, which seems more appropriate.
Signed-off-by: NDoug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>