Several people have noticed that crappy SD cards take much longer to
complete multiple block writes than the 300ms that Linux specifies.
Try to work around this by using a three second write timeout instead.

This is a generalized version of a patch from Chase Maupin
<Chase.Maupin@ti.com>, whose patch description said:

* With certain SD cards timeouts like the following have been seen
  due to an improper calculation of the dto value:
    mmcblk0: error -110 transferring data, sector 4126233, nr 8,
    card status 0xc00
* By removing the dto calculation and setting the timeout value
  to the maximum specified by the SD card specification part A2
  section 2.2.15 these timeouts can be avoided.
* This change has been used by beagleboard users as well as the
  Texas Instruments SDK without a negative impact.
* There are multiple discussion threads about this but the most
  relevant ones are:
    * http://talk.maemo.org/showthread.php?p=1000707#post1000707
    * http://www.mail-archive.com/linux-omap@vger.kernel.org/msg42213.html
* Original proposal for this fix was done by Sukumar Ghoral of
  Texas Instruments
* Tested using a Texas Instruments AM335x EVM
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes a compile error in drivers/mmc/host/sdhci-dove.c
by including the linux/module.h file.
Signed-off-by: NAlf Høgemark <alf@i100.no>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: NAl Cooper <acooper@gmail.com>
Acked-by: NArindam Nath <arindam.nath@amd.com>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This reverts commit e6039832.
There are reports of MSI breaking SDHCI on multiple chipsets (JMicron
and O2Micro, at least), so this should be reverted until we come up
with a whitelist or something.
Signed-off-by: NChris Ball <cjb@laptop.org>

This reverts commit c16e981b2fd9455af670a69a84f4c8cf07e12658, because
it's no longer useful once MSI support is reverted.
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc_select_powerclass() function returns error if eMMC
VDD level supported by host is between 2.7v to 3.2v.

According to eMMC specification, valid voltage for high
voltage cards is 2.7v to 3.6v. This patch ensures that
2.7v to 3.6v VDD range is treated as valid range.

Also, failure to set the power class shouldn't be treated
as fatal error because even if setting the power class
fails, card can still work in default power class.
If mmc_select_powerclass() returns error, just print
the warning message and go ahead with rest of the card
initialization.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Acked-by: NGirish K S <girish.shivananjappa@linaro.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

OMAP4 and OMAP3 HSMMC IP registers differ by 0x100 offset.
Adding the offset to platform_device resource structure
increments the start address for every insmod operation.
MMC command fails on re-insertion as module due to incorrect register
base.  Fix this by updating the ioremap base address only.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This will delete some boilerplate code, no functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If we put probe() on __init section, that will never work for multiple
module insertions/removals.

In order to make it work properly, move probe to __devinit section and
use platform_driver_register() instead of platform_driver_probe().
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

A bunch of non-functional cleanups to the omap_hsmmc driver.

It basically decreases indentation level, drop unneded dereferences
and drop unneded accesses to the platform_device structure.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Call context save api after enabling runtime pm to make sure that
register access in context save api happens with clk enabled.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

pm_runtime_put_sync instead of autosuspend pm runtime API
because iounmap(host->base) follows immediately.
Reported-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Neil Brown reports that commit 35cd133c

   PM: Run the driver callback directly if the subsystem one is not there

breaks suspend for his libertas wifi, because SDIO has a protocol
where the suspend method can return -ENOSYS and this means "There is
no point in suspending, just turn me off".  Moreover, the suspend
methods provided by SDIO drivers are not supposed to be called by
the PM core or bus-level suspend routines (which aren't presend for
SDIO).  Instead, when the SDIO core gets to suspend the device's
ancestor, it calls the device driver's suspend function, catches the
ENOSYS, and turns the device off.

The commit above breaks the SDIO core's assumption that the device
drivers' callbacks won't be executed if it doesn't provide any
bus-level callbacks.  If fact, however, this assumption has never
been really satisfied, because device class or device type suspend
might very well use the driver's callback even without that commit.

The simplest way to address this problem is to make the SDIO core
tell the PM core to ignore driver callbacks, for example by providing
no-operation suspend/resume callbacks at the bus level for it,
which is implemented by this change.
Reported-and-tested-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
[stable: please apply to 3.3-stable only]
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

When UHS-I card is detected also print the bus speed mode in which
UHS-I card will be running.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MSI on my O2Micro OZ600 SD card reader is broken.  This patch adds a quirk
to disable MSI on these controllers.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

There is no need to tune mmc->f_min to a value near 400kHz as the MMC core
begins testing frequencies at 400kHz regardless of the value of mmc->f_min.

As suggested by Guennadi Liakhovetski.

Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: NCao Minh Hiep <hiepcm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc->f_max should be half of the bus clock.
And now that mmc->f_max is not equal to the bus clock the
latter should be used directly to calculate mmc->f_min.

Cc: Magnus Damm <magnus.damm@gmail.com>
Tested-by: NCao Minh Hiep <hiepcm@gmail.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

Correct an off-by one error when calculating the clock divisor in cases
where the host clock is a power of two of the target clock.  Previously the
divisor was one greater than the correct value in these cases leading to
the clock being set at half the desired speed.

Thanks to Guennadi Liakhovetski for working with me on the logic for this
change.
Tested-by: NCao Minh Hiep <hiepcm@gmail.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to the specifications for SD and (e)MMC default
blocksize (named BLOCKLEN in Spec.) must always be 512
bytes. Since we hardcoded to always use 512 bytes, we do
not explicitly have to set it. Future improvements should
potentially make it possible to use a greater blocksize
than 512 bytes, but until then let's skip this.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: NSubhash Jadavani <subhashj@codeauora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add an odd clock divider capability available from v5xx. It also involves
changing the clock divider calculation, and changing the switch-case
statement to use top-down fallthrough.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The HSMCI operates at a rate of up to Master Clock divided by two.
Moreover previous calculation can cause overflows and so wrong
timeouts.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Since most of the work is already done by the core we just need to add
runtime suspend methods and tell the PM core that runtime PM is enabled
for this device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This matches current best practice as one can have runtime PM enabled
without system sleep and CONFIG_PM is defined for both.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.

By using devm_ioremap, it also removes a potential memory leak, because
there was no call to iounmap in the probe function.

The call to platform_get_resource was moved just to make it closer to the
place where its result it used.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NChris Ball <cjb@laptop.org>

The platform data is copied into driver's private data and the copy is
used for all access to the platform data. This simpifies the addition
of device tree support for the sdhci-s3c driver.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

max_width member in platform data can be used to derive the mmc bus transfer
width that can be supported by the controller.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDHCI controllers on Exynos4 do not include the sdclk divider as per the
sdhci controller specification. This case can be represented using the
sdhci quirk SDHCI_QUIRK_NONSTANDARD_CLOCK instead of using an additional
enum type definition 'clk_types'.

Hence, usage of clk_type member in platform data is removed and the sdhci
quirk is used. In addition to that, since this qurik is SoC specific,
driver data is introduced to represent controllers on SoC's that require
this quirk.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Currently if a platform wants to implement a non-standard card-detection
method, it would need to call tmio_mmc_cd_wakeup(), which is an inline
function, calling mmc_detect_change(). For this the platform would have
to link mmc_core statically into the kernel, losing the ability to build
it as a module. This patch adds a callback to the sh_mobile_sdhi driver,
which eliminates this dependency.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some boards need a preliminary setup stage to prepare the sdhi
controller.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

On sh-mobile platforms the MMC clock frequency for the TMIO MMC unit is
obtained from the same clock, as the one, that runtime power-manages the
controller. The SDHI glue code has to access that clock directly,
bypassing the runtime PM framework, to get its frequency, but it
shouldn't enable or disable it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The sdio_irq_enabled member of struct tmio_mmc_host is a left-over from the
previously removed SDIO IRQ workaround. It is no longer needed and can now
be removed too.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The controller power status flag does not have to be accessed from the
hot-plug detection code any more, it can now be removed from the platform
data and put in the controller private struct.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

To use TMIO MMC driver ability to interface to the generic MMC GPIO card
hotplug detection helper, the SDHI driver has to pass the GPIO number
from its own platform data.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the platform specifies the TMIO_MMC_HAS_COLD_CD flag, use the generic
MMC GPIO card hotplug helper.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The condition, whether we have to use the native TMIO card hotplug
detection interrupt, is rather complex, it is better to only calculate it
once and store in the private data.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Calculate the IRQ number, using gpio_to_irq() and use fixed flags: trigger
on both edges. This makes two out of four arguments of the
mmc_cd_gpio_request() function redundant.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NChris Ball <cjb@laptop.org>