Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field

Verified with the following filters:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:1 u32 ht 800: \
	match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:2 u32 ht 800: \
	match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:3 u32 ht 800: \
	match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:4 u32 ht 800: \
	match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).

Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through.  However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket.  As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.

In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP.  In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR.  This way we can avoid
having to do any byte swaps in order to validate the port number.

I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct.  This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.

In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read.  I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit c9f53e63 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.

This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: NTushar Dave <tushar.n.dave@oracle.com>
Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count.  Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it.  Then, it is hard to find actual
reason of CMA allocation failure.  CMA allocation should be guaranteed
to succeed so finding offending place is really important.

In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function.  This is preparation step to
add tracepoint to each page reference manipulation function.  With this
facility, we can easily find reason of CMA allocation failure.  There is
no functional change in this patch.

In addition, this patch also converts reference read sites.  It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: NJoonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I added this check in setup_tc to multiple drivers,

 if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)

Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.

A good smoke test is to setup mqprio with,

# tc qdisc add dev eth4 root mqprio num_tc 8 \
  map 0 1 2 3 4 5 6 7 \
  queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7

Fixes: e4c6734e ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: NSingh Krishneil <krishneil.k.singh@intel.com>
Reported-by: NJake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.

This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch ensures ixgbe will not try to offload hash tables from the
u32 module. The device class does not currently support this so until
it is enabled just abort on these tables.

Interestingly the more flexible your hardware is the less code you
need to implement to guard against these cases.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds initial support for offloading the u32 tc classifier. This
initial implementation only implements a few base matches and actions
to illustrate the use of the infrastructure patches.

However it is an interesting subset because it handles the u32 next
hdr logic to correctly map tcp packets from ip headers using the ihl
and protocol fields. After this is accepted we can extend the match
and action fields easily by updating the model header file.

Also only the drop action is supported initially.

Here is a short test script,

 #tc qdisc add dev eth4 ingress
 #tc filter add dev eth4 parent ffff: protocol ip \
	u32 ht 800: order 1 \
	match ip dst 15.0.0.1/32 match ip src 15.0.0.2/32 action drop

<-- hardware has dst/src ip match rule installed -->

 #tc filter del dev eth4 parent ffff: prio 49152
 #tc filter add dev eth4 parent ffff: protocol ip prio 99 \
	handle 1: u32 divisor 1
 #tc filter add dev eth4 protocol ip parent ffff: prio 99 \
	u32 ht 800: order 1 link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
 #tc filter add dev eth4 parent ffff: protocol ip \
	u32 ht 1: order 3 match tcp src 23 ffff action drop

<-- hardware has tcp src port rule installed -->

 #tc qdisc del dev eth4 parent ffff:

<-- hardware cleaned up -->
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.

This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.

This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.

CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an opportunity to bulk free SKBs during reclaiming of
resources after DMA transmit completes in ixgbe_clean_tx_irq.  Thus,
bulk freeing at this point does not introduce any added latency.

Simply use napi_consume_skb() which were recently introduced.  The
napi_budget parameter is needed by napi_consume_skb() to detect if it
is called from netpoll.

Benchmarking IPv4-forwarding, on CPU i7-4790K @4.2GHz (no turbo boost)
 Single CPU/flow numbers: before: 1982144 pps ->  after : 2064446 pps
 Improvement: +82302 pps, -20 nanosec, +4.1%
 (SLUB and GCC version 5.1.1 20150618 (Red Hat 5.1.1-4))

Joint work with Alexander Duyck.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now ATR is not handling IPv6 extended headers, so ATR is not
being performed on such packets. Fix that by skipping extended
headers when they are present. This also fixes a problem where
the ATR code was not checking that the inner protocol was actually
TCP before setting up the signature rules. Since the protocol check
is intimately involved with the extended header processing as well,
this all gets fixed together.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When FCoE is enabled with SR-IOV on the X550 NIC the hardware
generates MDD events.

This patch fixes these by setting the expected values in the
Tx context descriptors for FCoE/FIP frames and adding a flush
after writing the RDLEN register.
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If an outer UDP checksum is set, pass the skb up with CHECKSUM_NONE
so that the stack will check the checksum. Do not increment an
error counter, because we don't know that there is an actual error.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.

This patch:
  - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
    NETIF_F_ALL_CSUM is being used as a mask).
  - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
    use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry.  What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for VLAN promiscuous with SR-IOV enabled.

The code prior to this patch was only adding the PF to VLANs that the VF
had added.  As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited.  This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.

With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF.  By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF.  In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN.  The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a check to make certain mac_table was actually allocated and is not
NULL.  If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state.  Specifically the MAC address was
enabled for both VF 0 and the PF.  This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.

A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.

In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.

Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000

Result:
	MPSAR[0]               00000081
	MPSAR[254]             00000001

Expected Result, behavior after patch:
	MPSAR[0]               00000080
	MPSAR[254]             00000080
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.

Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was.  So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead.  This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance.  This change updates the code in general to
clean it up so it becomes clear what each step is doing.  From what I can
tell there a couple of bugs cleaned up in this code.

First is the fact that the MAC addresses were being double counted for the
PF.  As a result once entries up to 63 had been used you could no longer
add additional filters.

A simple test case for this:
  for i in `seq 0 96`
  do
    ip link add link ens8 name mv$i type macvlan
    ip link set dev mv$i up
  done

Test script:
  ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$

When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe_intr and ixgbe/ixgbevf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.

They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The commit dfaf891d ("ixgbe: Refactor the RSS configuration code")
introduced a few kernel-doc errors:

1) The function name is missing;
2) The format is wrong;
3) The short description is redundant.

Fix all the above for the correct execution of the kernel doc.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Delete a redundant include of net/vxlan.h.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.

skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().

Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implements the new netdev op to trust VF in ixgbe.

The administrator can turn on and off VF trusted by ip command which
supports trust message.
 # ip link set dev eth0 vf 1 trust on
or
 # ip link set dev eth0 vf 1 trust off

Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As per Eric Dumazet's previous patches:
(see commit (24d2e4a5) - tg3: use napi_complete_done())

Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout

GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>

Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
				rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS

igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result:  941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589

Alignment      Offset         Bytes    Bytes       Recvs   Bytes    Sends
Local  Remote  Local  Remote  Xfered   Per                 Per
Recv   Send    Recv   Send             Recv (avg)          Send (avg)
    8       8      0       0 1176930056  1475.36    797726   16384.00  71905

MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result:  941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763

Alignment      Offset         Bytes    Bytes       Recvs   Bytes    Sends
Local  Remote  Local  Remote  Xfered   Per                 Per
Recv   Send    Recv   Send             Recv (avg)          Send (avg)
    8       8      0       0 1175182320  50476.00     23282   16384.00  71816

i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.

Other drivers were only compile tested.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>