The pty driver does not clear its write buffer when commanded.
This is to avoid an apparent deadlock between parallel flushes from
both pty ends; specifically when handling either BRK or INTR input.
However, parallel flushes from this source is not possible since
the pty master can never be set to BRKINT or ISIG. Parallel flushes
from other sources are possible but these do not threaten deadlocks.

Annotate the tty buffer mutex for lockdep to represent the nested
tty_buffer locking which occurs when the pty slave is processing input
(its buffer mutex held) and receives INTR or BRK and acquires the
linked tty buffer mutex via tty_buffer_flush().
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Besides nested legacy_mutex locking which is required on pty pair
teardown, other nested pty operations require lock subclassing.

Move lock subclass definition to tty interface header, include/linux/tty.h,
and document its use.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In canon mode, the read buffer head will advance over the buffer tail
if the input > 4095 bytes without receiving a line termination char.

Discard additional input until a line termination is received.
Before evaluating for overflow, the 'room' value is normalized for
I_PARMRK and 1 byte is reserved for line termination (even in !icanon
mode, in case the mode is switched). The following table shows the
transform:

 actual buffer |  'room' value before overflow calc
  space avail  |    !I_PARMRK    |    I_PARMRK
 --------------------------------------------------
      0        |       -1        |       -1
      1        |        0        |        0
      2        |        1        |        0
      3        |        2        |        0
      4+       |        3        |        1

When !icanon or when icanon and the read buffer contains newlines,
normalized 'room' values of -1 and 0 are clamped to 0, and
'overflow' is 0, so read_head is not adjusted and the input i/o loop
exits (setting no_room if called from flush_to_ldisc()). No input
is discarded since the reader does have input available to read
which ensures forward progress.

When icanon and the read buffer does not contain newlines and the
normalized 'room' value is 0, then overflow and room are reset to 1,
so that the i/o loop will process the next input char normally
(except for parity errors which are ignored). Thus, erasures, signalling
chars, 7-bit mode, etc. will continue to be handled properly.

If the input char processed was not a line termination char, then
the canon_head index will not have advanced, so the normalized 'room'
value will now be -1 and 'overflow' will be set, which indicates the
read_head can safely be reset, effectively erasing the last char
processed.

If the input char processed was a line termination, then the
canon_head index will have advanced, so 'overflow' is cleared to 0,
the read_head is not reset, and 'room' is cleared to 0, which exits
the i/o loop (because the reader now have input available to read
which ensures forward progress).

Note that it is possible for a line termination to be received, and
for the reader to copy the line to the user buffer before the
input i/o loop is ready to process the next input char. This is
why the i/o loop recomputes the room/overflow state with every
input char while handling overflow.

Finally, if the input data was processed without receiving
a line termination (so that overflow is still set), the pty
driver must receive a write wakeup. A pty writer may be waiting
to write more data in n_tty_write() but without unthrottling
here that wakeup will not arrive, and forward progress will halt.
(Normally, the pty writer is woken when the reader reads data out
of the buffer and more space become available).
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If PARMRK is enabled, the available read buffer space computation is
overly-pessimistic, which results in severely throttled i/o, even
in the absence of parity errors. For example, if the 4k read buffer
contains 1k processed data, the input worker will compute available
space of 333 bytes, despite 3k being available. At 1365 chars of
processed data, 0 space available is computed.

*Divide remaining space* by 3, truncating down (if left == 2, left = 0).
Reported-by: NChristian Riesch <christian.riesch@omicron.at>

Conflicts:
	drivers/tty/n_tty.c
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add commit_head buffer index, which the producer-side publishes
after input processing in non-canon mode. This ensures the consumer-side
observes correctly-ordered writes in non-canonical mode (ie., the buffer
data is written before the buffer index is advanced). Fix consumer-side
uses of read_cnt() to use commit_head instead.

Add required memory barriers to the tail index to guarantee
the consumer-side has completed the loads before the producer-side
begins writing new data. Open-code the producer-side receive_room()
into the i/o loop.

Remove no-longer-referenced receive_room().

Based on work by Christian Riesch <christian.riesch@omicron.at>

Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The adjustments performed by receive_room() are to ensure a line
termination can always be written to the read buffer. However,
these adjustments are irrelevant to the throttle threshold (because
the threshold < buffer limit).
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty driver will be mistakenly throttled if a line termination
has not been received, and the line exceeds 3967 chars. Thus, it is
possible for the driver to stop sending when it has not yet sent
the newline. This does not apply to the pty driver.

Don't throttle until at least one line termination has been
received.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The input worker never reschedules itself; it only processes input until
either there is no more input or the read buffer is full. So the reader
is responsible for restarting the input worker only if the read buffer
was previously full (no_room == 1) _and_ space is now available to process
more input because the reader has consumed data from the read buffer.

However, computing the actual space available is not required to determine
if the reader has consumed data from the read buffer. This condition is
evaluated in 5 situations, each of which the space avail is already known:
1. n_tty_flush_buffer() - the read buffer is empty; kick the worker
2. n_tty_set_termios() - no data has been consumed; do not kick the worker
       (although it may have kicked the reader so data _will be_ consumed)
3. n_tty_check_unthrottle - avail space > 3968; kick the worker
4. n_tty_read, before leaving - only kick the worker if the reader has
       moved the tail. This prevents unnecessarily kicking the worker
       when timeout-style reading is used.
5. n_tty_read, before sleeping - although it is possible for the read
       buffer to be full and input_available_p() to be false, this can
       only happen when the input worker is racing the reader, in which
       case the reader will have been woken and won't sleep.

Rename n_tty_set_room() to n_tty_kick_worker() to reflect what the
function actually does.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for early console initialized from device tree
and kernel command line to all variants of Samsung serial driver.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
[mszyprow: added support for command line based initialization,
           fixed comments, added documentation]
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Tested-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When fifo overrun happened, the interrupt status refers to
SCLSR register in R-Car SCIF and HSCIF.
Thus, overrun handling takes SCLSR register into account.
Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the driver cannot return from overrun error if characters
are output during overrun process, use dev_dbg() instead of
dev_notice() to log the error message of overrun in syslog.

Based on a patch by Hisashi Nakamura.
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If we would like to send amount of data less than FIFO size we better would do
this via PIO mode. Otherwise the overhead could be significant.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we return in the first branch the second one doesn't require an
additional else keyword. The patch removes it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sci_{suspend|remove}() for the PM {freeze|
thaw|restore}() methods.  It's handy to achieve this by using SIMPLE_DEV_PM_OPS()
macro, however we have to annotate sci_{suspend|remove}() with '__maybe_unused'
in order to avoid compilation warnings when CONFIG_PM_SLEEP is undefined.

Based on orignal patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pty_space() computation is broken; the space already consumed
in the tty buffer is not accounted for.

Use tty_buffer_set_limit(), which enforces the limit automatically.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The implementation of flushing the RX FIFO breaks in a number of cases,
it is impossible to ensure an complete flush of the RX FIFO due to the
hardware not allowing the use of the FIFOs when the receiver is disabled
(Reading from the FIFO register does not remove it from the FIFO when
the RX_EN=0 or RX_DIS=1). Additionally during an initial set_termios
call where RX_DIS=1 causes a hang waiting forever for the RX FIFO to
empty. On top of this the FIFO will be cleared by the use of the RXRST
bits on the Control Register, making the RX flush pointless (as it does
not preserve the data read anyway).

Due to the TXRST the TX FIFO and transmitter can be interrupted during
frame trasmission, causing corruption and additionally data lost in the
FIFO. Most other serial drivers do not flush or clear the FIFOs during
a termios configuration change and as such do not have issues with
corruption. For this UART controller is it required that the TXRST/RXRST
bit be flagged during the change, this means that the data in the FIFO
will be dropped when changing configuration. In order to prevent data
loss and corruption of the transmitted data, wait until the TX FIFO is
empty before changing the configuration. The performance of this may
cause the set_termios call to take a longer amount of time especially
on lower baud rates, however it is comparable to the same performance
hit that a console_write call costs.
Signed-off-by: NNathan Rossi <nathan.rossi@xilinx.com>
Acked-by: NAnirudha Sarangi <anirudh@xilinx.com>
Acked-by: NHarini Katakam <harinik@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Building an arm allmodconfig kernel triggers a lengthy but harmless
warning in the isicom driver:

drvers/tty/isicom.c: In function 'isicom_send_break':
uapi/linux/swab.h:13:15: warning: integer overflow in expression [-Woverflow]
  (((__u16)(x) & (__u16)0x00ffU) << 8) |   \
               ^
uapi/linux/swab.h:107:2: note: in expansion of macro '___constant_swab16'
  ___constant_swab16(x) :   \
  ^
uapi/linux/byteorder/big_endian.h:34:43: note: in expansion of macro '__swab16'
 #define __cpu_to_le16(x) ((__force __le16)__swab16((x)))
                                           ^
linux/byteorder/generic.h:89:21: note: in expansion of macro '__cpu_to_le16'
 #define cpu_to_le16 __cpu_to_le16
                     ^
include/asm/io.h:270:6: note: in expansion of macro 'cpu_to_le16'
      cpu_to_le16(v),__io(p)); })
      ^
drivers/tty/isicom.c:1058:2: note: in expansion of macro 'outw'
  outw((length & 0xff00), base);
  ^

Apparently, the problem is related to the fact that the value 0xff00,
when used as a 16-bit number, is negative and passed into bitwise
operands of the generic byte swapping code.

Marking the input argument as unsigned in both technically correct
and avoids the warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need to explicitly zero the 'ret' variable as it is properly
initialized in a few lines below as:

ret = serial_mxs_probe_dt(s, pdev);

Remove the unneeded zeroing of 'ret'.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should check whether platform_get_irq() failed, and in the case of error
this needs to be propagated.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The irq number is only used inside the probe function, so there is no need
to keep it in the private mxs_auart_port structure.

Use a local 'irq' variable for storing the irq number instead.

Also make its type of 'int' as platform_get_irq() may fail and return a
negative number.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Digicolor USART hardware does not support detecting the BREAK condition.
This means that we can't support sysrq on this hardware. Remove all reference
to sysrq from the code.

This also fixes build when sysrq is disabled:

drivers/tty/serial/digicolor-usart.c: In function 'digicolor_uart_console_write':
drivers/tty/serial/digicolor-usart.c:407:33: error: 'struct uart_port' has no member named 'sysrq'
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the kernel command line parameter, no_console_suspend, is used,
the console should continue to output console messages during and
after system suspend. For a serial console, the serial core ensures
that the device is not shutdown when no_console_suspend is specified.
However, the default operation of the pnp bus will disable and suspend
the device and no further output occurs.

When registering the 8250 port, if the serial device is a console
set the PNP_CONSOLE capability, which prevents device power-off
if consoles are not suspending.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the serial console is an ACPI PNP device, the PNP bus always powers
down the device at system suspend, even though the no_console_suspend
command line parameter is specified (eg., when debugging suspend/resume).

Add PNP_CONSOLE capability, which when set, prevents calling both the
->disable() and ->suspend() PNP protocol methods if console suspend
is disabled.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

unregister_console() will be called from uart_remove_one_port() while
removing the platform driver. So not necessary to call it in driver
exit path.
Signed-off-by: NPramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The change does following:
 - baud, flow, bits, parity were being overwritten as they were
   being reinitialized after parsing.  Initialize them when they are
   declared so that user provided setting are not overwritten.
 - msm_set_baud_rate() is anyway called in uart_set_options when it calls
   msm_set_termios(). msm_reset() is called when we change the baud rate.
   Hence doing away with both of these calls.
 - CR_CMD_PROTECTION_EN and CR_TX_ENABLE settings are done in msm_set_baud_rate.
   So do away with this here.
Signed-off-by: NPramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Moorestown platform support was removed few years ago. This is a follow
up which removes Moorestown specific code for the serial devices. It includes
mrst_max3110 and earlyprintk bits.

This was used on SFI (Medfield, Clovertrail) based platforms as well, though
new ones use normal serial interface for the console service.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When running an userspace program that does a 'tcflush(fd, TCIOFLUSH)' call
we still see the last received character in the URXD register afterwards.

Clear UCR2_SRST bit so that the UART FIFO is flushed properly.

Since UCR2_SRST also resets some UART registers, we need to save and restore
some of them.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NFugang Duan <B38611@freescale.com>
Acked-by: NJason Liu <r64343@freecale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On uart buffer flush, serial core resets the circular buffer.
If a DMA transfer is in progress at that time, the callback
lpuart_dma_tx_complete will move buffer's tail unconditionally,
hence tail moves beyond head. Use the flush_buffer hook to
terminate the DMA imeaditely and avoid lpuart_dma_tx_complete
being called in this situation.

This bug often showed up while shutdown and lead to duplicate
serial console output.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For power management support, we should disable TX and
TX interrupt so that kernel can prepare for deep sleep.

Retain RX and RX interrupt for wakeup the kernel when
receive the input character.
Signed-off-by: NYuan Yao <yao.yuan@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To end a DMA transfer which did not consume a whole buffer (e.g. one
character only), a RX timer is used. When lots of data are received
the DMA transfer will complete and setup another DMA transfer, which
in turn might complete again. In this cases, it is not necessary to
abort the DMA transfers using the RX timer. This change pushes the
RX timer timeout into the future each time a DMA transfer completed.

Aborting the DMA was not very harmful, since the next received
character lead to setup of another RX DMA.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the DMA channel request to probe to avoid requesting the DMA
channel on each opening of the ttyLPx device. This also fixes a
potential issue that TX channel is not freed when only RX channel
allocation fails. The DMA channels are now handled independently,
so one could use UART with DMA only in TX direction for instance.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:

[   74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[   74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[   74.347817] Modules linked in:    0 S  0.0  0.0   0:00.00 writeback
[   74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[   74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[   74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[   74.370002] PC is at add_timer+0x24/0x28.0  0.0   0:00.09 kworker/u2:1
[   74.373960] LR is at lpuart_int+0x15c/0x3d8
[   74.378171] pc : [<80053070>]    lr : [<802e0d88>]    psr: a0010193
[   74.378171] sp : 8079de10  ip : 8079de20  fp : 8079de1c
[   74.389694] r10: 807d44c0  r9 : 8688c300  r8 : 00000013
[   74.394943] r7 : 20010193  r6 : 00000000  r5 : 000000a0  r4 : 86997210
[   74.401498] r3 : ffffa7da  r2 : 80817868  r1 : 86997210  r0 : 86997344
[   74.408052] Flags: NzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[   74.415489] Control: 10c5387d  Table: 8611c059  DAC: 00000015
[   74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...

Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.

This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:

[    7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[    7.516590] pgd = 86348000
[    7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[    7.526145] Internal error: Oops: 17 [#1] ARM
[    7.530611] Modules linked in:
[    7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[    7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[    7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[    7.553392] PC is at lpuart_timer_func+0x24/0xf8
[    7.558127] LR is at lpuart_timer_func+0x20/0xf8
[    7.562857] pc : [<802df99c>]    lr : [<802df998>]    psr: 600b0113
[    7.562857] sp : 86ac9b90  ip : 86ac9b90  fp : 86ac9bbc
[    7.574467] r10: 80817180  r9 : 80817b98  r8 : 80817998
[    7.579803] r7 : 807acee0  r6 : 86989000  r5 : 00000100  r4 : 86997210
[    7.586444] r3 : 86ac8000  r2 : 86ac9bc0  r1 : 86997210  r0 : 00000000
[    7.593085] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[    7.600341] Control: 10c5387d  Table: 86348059  DAC: 00000015
[    7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)

Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 26df6d13 ("tty: Add EXTPROC support for LINEMODE")
allows a process which has opened a pty master to send _any_ signal
to the process group of the pty slave. Although potentially
exploitable by a malicious program running a setuid program on
a pty slave, it's unknown if this exploit currently exists.

Limit to signals actually used.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Howard Chu <hyc@symas.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org> # 2.6.36+
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The vcs device's poll/fasync support relies on the vt notifier to signal
changes to the screen content.  Notifier invocations were missing for
changes that comes through the selection interface though.  Fix that.

Tested with BRLTTY 5.2.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Cc: Dave Mielke <dave@mielke.cc>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: NStanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

This reverts commit da788acb.

That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.

Cc: stable@vger.kernel.org # 3.17
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

Lockdep reported a possible deadlock between the cpuclk lock and for example
the i2c driver.

       CPU0                    CPU1
       ----                    ----
  lock(clk_lock);
                               local_irq_disable();
                               lock(&(&i2c->lock)->rlock);
                               lock(clk_lock);
  <Interrupt>
    lock(&(&i2c->lock)->rlock);

 *** DEADLOCK ***

The generic clock-types of the core ccf already use spin_lock_irqsave when
touching clock registers, so do the same for the cpuclk.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed initialization of "flags"]

Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.

I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.

[1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimusSigned-off-by: NTyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>