MAC on CN10K silicon support loopback for selftest or debug purposes.
This patch does necessary configuration to loopback packets upon receiving
request from LMAC mapped RVU PF's netdev via mailbox.

Also MAC (CGX) on OcteonTx2 silicon variants and MAC (RPM) on
OcteonTx3 CN10K are different and loopback needs to be configured
differently. Upper layer interface between RVU AF and PF netdev is
kept same. Based on silicon variant appropriate fn() pointer is
called to config the MAC.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RPM supports below list of counters as an extension to existing counters
 *  class based flow control pause frames
 *  vlan/jabber/fragmented packets
 *  fcs/alignment/oversized error packets

This patch adds support to display supported RPM counters via debugfs
and define new mbox rpm_stats to read all support counters.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow control configuration is different for CGX(Octeontx2)
and RPM(CN10K) functional blocks. This patch adds the necessary
changes for RPM to support 802.3 pause frames configuration on
cn10k platforms.
Signed-off-by: NRakesh Babu <rsaladi2@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CN10K supports max MTU of 16K on LMAC links and 64k on LBK
links and Octeontx2 silicon supports 9K mtu on both links.
Get the same from nix_get_hw_info mbox message in netdev probe.

This patch also calculates receive buffer size required based
on the MTU set.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OcteonTx3 CN10K silicon supports bigger MTU when compared
to 9216 MTU supported by OcteonTx2 silicon variants. Lookback
interface supports upto 64K and RPM LMAC interfaces support
upto 16K.

This patch does the necessary configuration and adds support
for PF/VF drivers to retrieve max packet size supported via mbox

This patch also configures tx link credit by considering supported
fifo size and max packet length for Octeontx3 silicon.

This patch also removes platform specific name from the driver name.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIX uses unique channel numbers to identify the packet sources/sinks
like CGX,LBK and SDP. The channel numbers assigned to each block are
hardwired in CN9xxx silicon.
The fixed channel numbers in CN9xxx are:

0x0 | a << 8 | b            - LBK(0..3)_CH(0..63)
0x0 | a << 8                - Reserved
0x700 | a                   - SDP_CH(0..255)
0x800 | a << 8 | b << 4 | c - CGX(0..7)_LMAC(0..3)_CH(0..15)

All the channels in the above fixed enumerator(with maximum
number of blocks) are not required since some chips
have less number of blocks.
For CN10K silicon the channel numbers need to be programmed by
software in each block with the base channel number and range of
channels. This patch calculates and assigns the channel numbers
to efficiently distribute the channel number range(0-4095) among
all the blocks. The assignment is made based on the actual number of
blocks present and also contiguously leaving no holes.
The channel numbers remaining after the math are used as new CPT
replay channels present in CN10K. Also since channel numbers are
not fixed the transmit channel link number needed by AF consumers
is calculated by AF and sent along with nix_lf_alloc mailbox response.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OcteonTx2's next gen platform the CN10K has RPM MAC which has a
different serdes when compared to CGX MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with CGX MAC, with few exceptions though. So we are using the same
CGX driver for RPM MAC as well and will have a different set of APIs
for RPM where ever necessary.

This patch adds initial support for CN10K's RPM MAC i.e. the driver
registration, communication with firmware etc. For communication with
firmware, RPM provides a different IRQ when compared to CGX.
The CGX and RPM blocks support different features. Currently few
features like ptp, flowcontrol and higig are not supported by RPM. This
patch adds new mailbox message "CGX_FEATURES_GET" to get the list of
features supported by underlying MAC.

RPM has different implementations for RX/TX stats. Unlike CGX,
bar offset of stat registers are different. This patch adds
support to access the same and dump the values in debugfs.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to use new LMTST lines for NPA batch free
and burst SQE flush. Adds new dev_hw_ops structure to hold platform
specific functions and create new files cn10k.c and cn10k.h.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On CN10K platform transmit/receive buffer alloc and free from/to hardware
had changed to support burst operation. Whereas pervious silicon's only
support single buffer free at a time.
To Support the same firmware allocates a DRAM region for each PF/VF for
storing LMTLINES. These LMTLINES are used for NPA batch free and for
flushing SQE to the hardware.
PF/VF LMTST region is accessed via BAR4. PFs LMTST region is followed
by its VFs mbox memory. The size of region varies from 2KB to 256KB based
on number of LMTLINES configured.

This patch adds support for
- Mapping PF/VF LMTST region.
- Reserves 0-71 (RX + TX + XDP) LMTST lines for NPA batch
  free operation.
- Reserves 72-512 LMTST lines for NIX SQE flush.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On CN10K platform NIX RQ and SQ context structure got changed.
This patch uses new mbox message "NIX_CN10K_AQ_ENQ" for NIX
context initialization on CN10K platform.

This patch also updates the nix_rx_parse_s and nix_sqe_sg_s
structures to add packet steering bit feilds.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On CN10K platform NPA and NIX context structure bit fields
had changed to support new features like bandwidth steering etc.
This patch dumps approprate context for CN10K platform.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIX hardware context structure got changed to accommodate new
features like bandwidth steering, L3/L4 outer/inner checksum
enable/disable etc., on CN10K platform.
This patch defines new mbox message NIX_CN10K_AQ_INST for new
NIX context initialization.

This patch also updates the NPA context structures to accommodate
bit field changes made for CN10K platform.

This patch also removes Big endian bit fields from existing
structures as its support got deprecated in current and upcoming silicons.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitate communication between AF-PF and PF-VF.

On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.

On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.

This patch changes mbox initialization to support both CN9XX and CN10K
platform.
The patch also adds new hw_cap flag to setting hw features like TSO etc
and removes platform specific name from the PF/VF driver name to make it
appropriate for all supported platforms

This patch also removes platform specific name from the PF/VF driver name
to make it appropriate for all supported platforms
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitates communication between AF-PF and PF-VF.

On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.

On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.

This patch changes mbox initialization to support both CN9XX and CN10K
platform.

This patch also adds CN10K PTP subsystem and device IDs to ptp
driver id table.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch check that TX FC firmware is running in CM3.
If not, global TX FC would be disabled.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix GMAC TX flow control autoneg.
Flow control autoneg wrongly were disabled with enabled TX
flow control.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current  FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add ethtool flow control configuration support.

Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.

Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.

Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".

This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds CM3 memory map.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This entry used when skipping the parser needed,
for example, the custom header pretended to ethernet header.
Suggested-by: NLiron Himi <liron@marvell.com>
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register set_link_ksetting callback with driver such that
link configurations parameters like advertised mode,speed, duplex
and autoneg can be configured.

below command
ethtool -s eth0 advertise 0x1 speed 10 duplex full autoneg on
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register get_link_ksettings callback to get link status information
from the driver. As virtual function (vf) shares same physical link
same API is used for both the drivers and for loop back drivers
simply returns the fixed values as its does not have physical link.

ethtool eth3
Settings for eth3:
        Supported ports: [ ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
                                10000baseKR/Full
                                1000baseX/Full
        Supports auto-negotiation: No
        Supported FEC modes: BaseR RS
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: None

ethtool lbk0
Settings for lbk0:
	Speed: 100000Mb/s
        Duplex: Full
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CGX supports setting advertised link modes on physical link.
This patch adds support to derive cgx mode from ethtool
link mode and pass it to firmware to configure the same.
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CGX LMAC, the physical interface support link configuration parameters
like speed, auto negotiation, duplex  etc. Firmware saves these into
memory region shared between firmware and this driver.

This patch adds mailbox handler set_link_mode, fw_data_get to
configure and read these parameters.
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool support to configure fec modes baser/rs and
support to fecth FEC stats from CGX as well PHY.

Configure fec mode
	- ethtool --set-fec eth0 encoding rs/baser/off/auto
Query fec mode
	- ethtool --show-fec eth0
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to fetch fec stats from PHY. The stats are
put in the shared data struct fwdata.  A PHY driver indicates
that it has FEC stats by setting the flag fwdata.phy.misc.has_fec_stats

Besides CGX_CMD_GET_PHY_FEC_STATS, also add CGX_CMD_PRBS and
CGX_CMD_DISPLAY_EYE to enum cgx_cmd_id so that Linux's enum list is in sync
with firmware's enum list.
Signed-off-by: NFelix Manlunas <fmanlunas@marvell.com>
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CGX block supports forward error correction modes baseR
and RS. This patch adds support to set encoding mode
and to read corrected/uncorrected block counters

Adds new mailbox handlers set_fec to configure encoding modes
and fec_stats to read counters and also increase mbox timeout
to accomdate firmware command response timeout.

Along with new CGX_CMD_SET_FEC command add other commands to
sync with kernel enum list with firmware.
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pavel pointed that the return of dma_addr_t in
otx2_alloc_rbuf/__otx2_alloc_rbuf() seem suspicious because a negative
error code may be returned in some cases. For a dma_addr_t, the error
code such as -ENOMEM does seem a valid value, so we can't judge if the
buffer allocation fail or not based on that value. Add a parameter for
otx2_alloc_rbuf/__otx2_alloc_rbuf() to store the dma address and make
the return value to indicate if the buffer allocation really fail or
not.
Reported-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Tested-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: NAlexander Duyck <alexanderduyck@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Tested-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleans up all resources
attached to that VF. This patch adds support to handle
CPT FLR.
Signed-off-by: NNarayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: NSuheil Chandran <schandran@marvell.com>
Signed-off-by: NSunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: NSrujana Challa <schalla@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Adds support to display block CPT1 stats at
"/sys/kernel/debug/octeontx2/cpt1".
Signed-off-by: NMahipal Challa <mchalla@marvell.com>
Signed-off-by: NSrujana Challa <schalla@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch changes CPT mailbox message format to
support new block CPT1 in 98xx silicon.

cpt_rd_wr_reg ->
    Modify cpt_rd_wr_reg mailbox and its handler to
    accommodate new block CPT1.
cpt_lf_alloc ->
    Modify cpt_lf_alloc mailbox and its handler to
    configure LFs from a block address out of multiple
    blocks of same type. If a PF/VF needs to configure
    LFs from both the blocks then this mbox should be
    called twice.
Signed-off-by: NMahipal Challa <mchalla@marvell.com>
Signed-off-by: NSrujana Challa <schalla@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>