提交 · 1c901a46d576926287b05fc145bd3fd31a3e65de · openeuler / Kernel

16 9月, 2011 29 次提交

stmmac: add MMC support exported via ethtool (v3) · 1c901a46

由 Giuseppe CAVALLARO 提交于 9月 01, 2011

This patch adds the MMC management counters support.
MMC module is an extension of the register address
space and all the hardware counters can be accessed
via ethtoo -S ethX.

Note that, the MMC interrupts remain masked and the logic
to handle this kind of interrupt will be added later (if
actually useful).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1c901a46

stmmac: support wake up irq from external sources (v3) · 3172d3af

由 Deepak Sikri 提交于 9月 01, 2011

On some platforms e.g. SPEAr the wake up irq differs from the
GMAC interrupt source.
With this patch an external wake up irq can be passed through the
platform code and named as "eth_wake_irq".

In case the wake up interrupt is not passed from the platform
so the driver will continue to use the mac irq (ndev->irq)
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3172d3af

stmmac: remove the mmc code (v3) · 26a051cc

由 Giuseppe CAVALLARO 提交于 9月 01, 2011

DWMAC Management Counters (MMC) are not fully support.
The minimal support added in the past allowed to
only disable counters (if present) and mask their
interrupts.
This patch prepares the driver to support the MMC
removing obsolete code.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

26a051cc

stmmac: remove the STBus bridge setting from the GMAC code (v3) · 2e19a381

由 Giuseppe CAVALLARO 提交于 9月 01, 2011

This patch removes a piece of code (actually commented)
only useful for some ST platforms in the past.

This kind of setting now can be done by using the platform
callbacks provided in linux/stmmac.h (see the stmmac.txt for
further details).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

2e19a381

bna: Driver Version changed to 3.0.2.1 · 3e829a78

由 Rasesh Mody 提交于 8月 30, 2011

Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3e829a78

bna: SKB PCI UNMAP Fix · 938fa488

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Found a leak in sk_buff unmapping of PCI dma addresses where boundary
   conditions are not properly handled in freeing all Tx buffers. Freeing
   of all Tx buffers is done considering sk_buffs data and fragments can
   be mapped at the boundary.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

938fa488

bna: TX Queue Depth Fix · 41eb5ba4

由 Rasesh Mody 提交于 8月 30, 2011

sk_buff unmap_array grows greater than 65536 (x2) with Tx ring of 65536.
Reducing TXQ depth and safe(max) acking of Tx events to 32768 (same as Rx).
Add defines for TX and RX queue depths.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

41eb5ba4

bna: MBOX IRQ Flag Check after Locking · dfee325a

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Check the BNAD_RF_MBOX_IRQ_DISABLED flag after acquiring the bna_lock,
   since checking the flag and executing bna_mbox_handler needs to be atomic.
   If not, it opens up window where flag is reset when it was checked, but got
   set while spinning on the lock by the other thread which is actually
   holding the lock
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dfee325a

bna: Async Mode Tx Rx Init Fix · 761fab37

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Async mode of Tx/Rx queue initialization in BNAD from a task queue context
   runs into non-unique taskq allocation issues. Get rid of Tx/Rx
   initialization from task q context
 - In the attach function, wait for IOC enable, then do Tx/Rx queue
   initialization. Default BNA attributes are used when IOC enable from attach
   fails and values are set to:
   1 TxQ, 1 RxQ, 1 Unicast MAC, 1 RIT entry
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

761fab37

bna: Ethtool Enhancements and Fix · a2122d95

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Add tx_skb counters and NAPI debug counters to ethtool stats.
 - Add rlb stats strings to bnad_net_stats_strings{} array. rlb_stats field
   was added to struct bfi_enet_stats {} but the corresponding name structure
   array for ethtool was not initialized with right strings, even though the
   actual name structure array got expanded. This caused a NULL pointer
   violation and a crash when doing ehtool -S <if_name>.
 - Modify dim timer stop logic to make it dependent on cfg and run flags
 - While setting the ring parameter restore the rx, vlan configuration and
   set rx mode
 - Indentation fix
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

a2122d95

bna: Initialization and Locking Fix · 3caa1e95

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Initialize rx_id to 0 for bnad_cleanup_rx
 - Return -ENOMEM in case if bna_rx_create fails
 - Count the Rx buffer allocation failures in bnad_alloc_n_post_rxbufs()
 - Remove unnecessary initialization of using_dac to false in bnad_pci_probe
 - Release lock if error while doing bna_num_txq_set in bnad_pci_probe
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3caa1e95

bna: Formatting and Code Cleanup · 19dbff9f

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Print log messages when running with reduced number of MSI-X vectors
   and when defaulting to INTx mode.
 - Remove BUG_ONs and header file inclusion that are not needed
 - Comments addition/cleanup
 - Unused code cleanup
 - Add New Line to Print msg in bfa_sm_fault
 - Formatting fix
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

19dbff9f

bna: TX Path and RX Path Changes · 271e8b79

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Add bnad_pci_unmap_skb() API to unmap skb from transmit path and update the
   unmap index. Add more checks for illegal skbs in transmit path. Add tx_skb
   counters for dropped skbs.
 - The unmap_cons index used in bnad_free_txbufs() is incorrectly declared as
   u16. It quickly wraps around and accesses null sk_buff ptr. So using u32 to
   handle unmap_array.
 - Disable and enable interrupts from the same polling context to prevent
   reordering in Rx path.
 - Add Rx NAPI debug counters.
 - Make NAPI budget check more generic.
 - Modify dim timer stop logic to make it dependent on cfg and run flags
 - Handle reduced MSI-X vectors case in bnad_enable_msix.
 - Check for single frame TSO skbs and send them out as non-TSO.
 - Put memory barrier after bna_txq_prod_indx_doorbell().
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

271e8b79

bna: Interrupt Polling and NAPI Init Changes · 2be67144

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Remove unnecessary ccb check from bnad_poll_cq
 - Add bnad pointer to rx_ctrl structure, so that bnad can be accessed directly
   from rx_ctrl in the NAPI poll routines, even if ccb is NULL
 - Validate ccb before referencing to it in bnad_msix_rx and bnad_napi_poll_rx
 - Fix the order of NAPI init / uninit in Tx / Rx setup / teardown path:
   a. Kill bnad tx free tasklet ahead of call to bna_tx_destroy()
   b. Call NAPI disable only after call to Rx free_irq(). This makes sure Rx
      interrupt does not schedule a poll when NAPI is already disabled
 - NAPI poll runs before the h/w has completed configuration. This causes a
   crash. Delay enabling NAPI till after bna_rx_enable(). Split NAPI
   initialization into 2 steps, bnad_napi_init() & bnad_napi_enable().
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

2be67144

bna: PCI Probe Fix · 0caa9aae

由 Rasesh Mody 提交于 8月 30, 2011

Change details:
 - Return error as -EIO if bnad_res_alloc fails
 - Release the configuration lock before registering with net_device layer.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

0caa9aae

bna: Naming Change and Minor Macro Fix · 772b5235

由 Rasesh Mody 提交于 8月 30, 2011

Naming changes: rename devid, BNAD_MAX_TXS, BNAD_MAX_RXS,
BNAD_MAX_RXPS_PER_RX to device, BNAD_MAX_TX, BNAD_MAX_RX,
BNAD_MAX_RXP_PER_RX respectively and change all the references.

Macro Fix: Add ioc_isr_mod_set check to bfa_nw_ioc_mbox_regisr macro
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

772b5235

r8169: convert to SKB paged frag API. · 929f6189