Track the connection status per-VIF.
The data path code is also updated to support multiple VIFs.
This includes RX and TX VRING management, NAPI poll loops,
RX reordering and related code.
Power management code used to check if the main interface
is up or based on connection state of the main interface,
adapt this code to take all VIFs into account.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Simple infrastructure changes for supporting multiple
virtual interfaces (multiple VIFs).
It is still not possible to add new VIFs so the only VIF
belongs to the main interface.
Main changes:
1. Add MAC ID(mid) argument to wmi_send and wmi_call to
allow invoking WMI commands on different VIFs.
2. Similarly, in WMI event handler look at the mid reported
by FW and extract VIF structure (currently only for main
interface). All WMI event handlers operate on wil6210_vif
structure so they know on which VIF they were called.
3. Trivial changes to use wil6210_vif structure and MID
throughout the code.
4. Various changes to logging to report MID.

More complete multiple VIFs support will be added gradually
in next patches.
Signed-off-by: NLior David <liord@codeaurora.org>
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The field preset_chandef of wireless_dev must not be accessed
by the driver because it is private to cfg80211. Store the
monitor channel locally in wil6210_priv instead.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the option to support 40bit addresses since some platforms
may not support 48bits but support 40bits
Signed-off-by: NLazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

vring_idle_trsh is used in the operational driver, hence
should not be defined as a debugfs variable.
Signed-off-by: NGidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

    @@
    expression SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - fn(SKB, LEN)[0]
    + *(u8 *)fn(SKB, LEN)

Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 11ad spec requires 11ad devices to be able to receive 8KB
packets over the air. Currently this is only possible by
loading the driver with mtu_max=7912 but this also forces
a smaller block ACK window size which reduces performance
for stations which transmit normal sized packets (<2KB).
Fix this problem as follows:
1. Add a module parameter rx_large_buf that when set,
will allocate 8KB RX buffers regardless of mtu_max
setting.
2. When receiving block ACK request agree to any window
size not above our maximum, regardless of the mtu_max setting.
This means if the other side transmits small packets (2KB)
it can still set up block ACK with a large window size,
and get better performance.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

device supports 48bit addresses, reflect that by
setting the dma mask accordingly.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Symbolic permissions are no longer recommended.
This patch changes the symbolic permissions in wil6210 driver
to octal permissions.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently we do not have full support for broadcast from
a station inside a PBSS network.
We have a workaround where instead of broadcast we do a
unicast to every known station in the PBSS.
This workaround was performed only for P2P clients.
This fix will perform the broadcast workaround also for a
regular station inside a PBSS.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

__func__ is automatically added to printouts by dynamic debug
mechanism and by wil_info/wil_err macros.
Remove __func__ from debug printouts to avoid duplication.
Signed-off-by: NLazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch fix spelling typos in printk and kconfig.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Driver calls to netif_tx_stop_all_queues/netif_tx_wake_all_queues are
inconsistent. In several cases, driver can get to a situation where net
queues are stopped forever and data cannot be sent.

The fix is to stop net queues if there is at least one vring which is
"full" and to wake net queues if all vrings are not "full".
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

txdata->enabled is used in order to determine if the TX vring
is valid. As the data transmit is handled in a different context,
in case txdata->enabled is set before vring->hwtail is updated,
an old or corrupted vring->hwtail can be used.
Protect setting of txdata->enabled and vring->hwtail to prevent a
case where TX vring start handling TX packets before setting
vring->hwtail.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case we fail to map one of the TSO SKB fragments, we need to
clear all the mapped descriptors, from swhead to swhead+descs_used-1.

Change the desc index calculation to
i = (swhead + descs_used - 1) % vring->size;
to prevent unmpping of (swhead + descs_used) descriptor that wasn't
mapped.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

napi_synchronize is called before releasing the vring, with the
assumption that setting txdata->enabled to 0 will prevent handling
of this vring in the next scheduled napi.
To guarantee this assumption, a memory barrier is added after disabling
the txdata.
In addition, as the ctx is zeroed in wil_tx_complete after this
descriptor is handled (protected by wmb), ctx needs to be checked
before releasing this descriptor in wil_vring_free.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

add memory barrier after allocating new rx descriptors, before
updating the hwtail.
This will guarantee that all writes to descriptors (shared memory)
are done before committing them to HW.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are 2 possible race conditions, both are solved by addition of
memory barrier:
1. wil_tx_complete reads the swhead to determine if the vring is
empty. In case the swhead was updated before the descriptor update
was performed in __wil_tx_vring/__wil_tx_vring_tso, the completion
loop will not end and as the DU bit may still be set from a previous
run, this skb can be handled as completed before it was sent, which
will lead to double free of the same SKB.
2. __wil_tx_vring/__wil_tx_vring_tso calculate the number of available
descriptors according to the swtail. In case the swtail is updated
before memset of ctx to zero is completed, we can handle this
descriptor while later on ctx is zeroed.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Network stack can try to transmit data while AP / STA is
disconnected.
Change this print-out to debug level as this should not be
handled as error.
This patch also adds wil_dbg_ratelimited, used to limit the
above print-out.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Switch to auto-generated version of wmi.h which is maintained
by FW team. This will allow better sync between teams in the
future and avoid bugs because of unexpected API changes.
The wmi.h will have many differences but most are cosmetic.
It also includes these real differences:
1. is_go parameter added to BCON_CTRL and START_PCP commands.
2. max_rx_pl_per_desc added to CFG_RX_CHAIN command.
3. various small API updates that are not currently used by
driver.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Check PN for encrypted frames.
Maintain PN data for Rx keys, pairwise per TID and group.
Print PN's in the debugfs "stations" entry, like:

[0] 04:ce:14:0a:3c:3d connected
  [ 0] ([32]   0 TU) 0x0fe [____________________________|___] total 252 drop 0 (dup 0 + old 0) last 0x000
  [ 0] PN [0+]000000000000 [1-]000000000000 [2-]000000000000 [3-]000000000000
  [GR] PN [0-]000000000000 [1+]000000000000 [2+]000000000000 [3-]000000000000
Rx invalid frame: non-data 0, short 0, large 0, replay 0
Rx/MCS: 0 110 65 65 65 0 12 0 0 0 0 0 0
[1] 00:00:00:00:00:00 unused
[2] 00:00:00:00:00:00 unused
[3] 00:00:00:00:00:00 unused
[4] 00:00:00:00:00:00 unused
[5] 00:00:00:00:00:00 unused
[6] 00:00:00:00:00:00 unused
[7] 00:00:00:00:00:00 unused
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wil_tx_vring locks the vring_tx_data lock before accessing the TX
vring to check if it is enabled and valid for use.
In case of quick disconnect / connect events for the same station,
spin_lock(&txdata->lock) can be called during the lock initialization
in the vring init function.
To prevent such a race, the TX vrings spin lock should be initialized
once during wil6210 driver initialization.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the current solution wil6210 configures the vring in a worker
and holds only one pending CID. This implementation may lead to
race conditions between connect and disconnect events of multiple
stations or fast connect/disconnect events of the same station.

In order to allow the removal of the connect worker and handling of
WMI_VRING_CFG_DONE_EVENTID in the connect event, the WMI replies
that provide the reply in a given buffer needs to be handled
immediately in the WMI event interrupt thread.
To prevent deadlocks, WMI replies that requires additional
handling are still handled via the events list.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In TX vring allocation, vring_tx->va is allocated before WMI command to
configure the vring is sent to the device. As the WMI command can take
time to complete, it can lead to scenarios where vring_tx->va is not NULL
but vring is still not enabled.

This patch adds a check that vring_tx_data is enabled before returning
a valid TX vring.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To prevent race when connect flow may run in parallel with
the disconnect event.

Scenario leading to the bug is: while running connect flow on the AP,
STA sends disconnect. log follows.

<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Configure for connection CID 1
<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_init_tx() max_mpdu_size 2048
<7>[  668.736301] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_alloc()
<7>[  668.736363] wil6210 0000:01:00.0: wlan0: DBG[MISC]vring[1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Head 0x00880300 -> 0x00880308
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI command 0x0821 [28]
<7>[  668.736426] DBG[ WMI]Cmd 00000000: 20 00 24 00 00 00 00 00 00 00 21 08 00 00 00 00   .$.......!.....
<7>[  668.736426] DBG[ WMI]cmd 00000000: 00 00 00 00 00 00 5f 5c 00 00 00 00 00 04 00 08  ......_\........
<7>[  668.736457] DBG[ WMI]cmd 00000010: 01 01 00 00 00 00 00 00 00 00 ff 0f              ............
<7>[  668.736488] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Pseudo IRQ 0x00000004
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1824 (reply_id 0x1821)
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_mask_irq_pseudo()
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]ISR MISC 0x20000000
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1003 (reply_id 0x1821)
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Disconnect 04:ce:14:00:07:70 reason [proto 3 wmi 4]
<7>[  668.736582] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread IRQ
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread ISR MISC 0x20000000
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]MBOX event
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox head 00880330 tail 00880328
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox evt 001a 0010 0000 00
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI event 0x1821 MID 0 @3255145 msec
<7>[  668.736707] DBG[ WMI]evt 00000000: 1a 00 10 00 00 00 00 10 00 00 21 18 69 ab 31 00  ..........!.i.1.
<7>[  668.736707] DBG[ WMI]evt 00000010: 01 01 00 00 00 00 00 00                          ........
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]queue_work -> 0
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_recv_cmd -> 1 events queued
<7>[  668.736769] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_unmask_irq_pseudo()
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=1, reason=3
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_disconnect_cid(CID 1, status 1)
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_fini_tx() id=1
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736957] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1821 (reply_id 0x1821)
<7>[  668.736988] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Complete WMI 0x1821
<7>[  668.737019] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_call(0x0821->0x1821) completed in 0 msec
<3>[  668.737019] wil6210 0000:01:00.0: wlan0: Tx config failed, status 0x01
<7>[  668.739518] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_cfg80211_del_station(04:ce:14:00:07:70, reason=2)
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]_wil6210_disconnect(bssid=04:ce:14:00:07:70, reason=2, ev-)
<7>[  668.739581] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=-2, reason=2
<7>[  668.742705] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0x  (null):d962ce08 0x  (null)
<3>[  668.742736] __dma_free_remap: trying to free invalid coherent area:   (null)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.

In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Situations observed when IP stack schedules lots of
frames for Tx while no connection (connection lost,
for example). In this case, dmesg bloated with error
message "FW not connected", printed for every frame.

Ratelimit this error message to avoid dmesg pollution.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

BAR frames delivered to the host via Rx path; whole BAR frame
get delivered. Advance sequence in the reorder buffer and release
old frames, as per IEEE802.11 spec.

Firmware will reply to BAR, driver responsibility is only reorder
buffer management.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

On Rx, when invalid frame is received and dropped,
reaping of next frames from Rx ring is stopped.

This stops NAPI polling and re-enables the Rx interrupt.

However, in cases where no more frames received,
interrupt will not be triggered and rest of Rx frames
will not be processed.

Skip bad frames and continue to reap Rx packets when
such frames are encountered, and add statistics for
such frames for debug.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Allow network stack part of Rx processing to run on separate core,
relaxing CPU utilization on the core used for Rx NAPI.

If RXHASH feature is enabled, the driver sets rxhash of each skb to 1
to enable RPS. The core for processing the rx skb is determined by RPS
mechanism according to rx_cpus bit mask which is configured at user level.
For processing skbs on different core from the core which processes
the interrupts, it is recommended not to enable core 0 in rx_cpus bit mask.
Signed-off-by: NVladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".

Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Driver report supported TSO (v4 & v6) and IP checksum offload
in addition to previously supported features. In data path
skbs are checked for non-zero gso_size, and when detected sent
to additional function for processing TSO SKBs. Since HW does not
fully support TSO, additional effort is required from the driver.
Driver partitions the data into mss sized descriptors which are
then DMAed to the HW.
Signed-off-by: NVladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Provide detailed statistics for the Rx frames per MCS
Statistics printed in "stations" debugfs entry
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Introduce 2 types of GTK, Tx (for this STA) and Rx (for each peer).
Now, AP has only Tx GTK, STA - only Rx one. PBSS not supported yet;
for it, continue using pseudo-DMS.
Handle per-vring .1x state, update it from WMI_VRING_EN_EVENTID
event. This allows unification for unicast and broadcast vrings.
This mechanism replaces former per-CID "data_port_open"
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Rx descriptor fields accordingly to the updated
hardware documentation
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Multicast is not yet properly supported for all connection types;
actually, only non-secure AP is supported. For all other cases,
fall back to old "pseudo-DMS" approach. Namely, for:
- PBSS
- secure connection

When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin
of the frame
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations

For short frames, use MCS0; for long - MCS1
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For the networking code and for hardware network accelerators,
it is better to have IP header 4*n aligned. On the other side,
DMA on Rx path require buffer to be aligned on 4*n as well.
Having 14 bytes of Ethernet header, these 2 alignment
requests are in contradiction.

To solve this, order hardware offload block to not remove
SNAP header. This adds extra 6 bytes between addresses and
ethertype, making it 20 bytes total. This way, both buffer and
IP header are 4*n aligned. Remaining is only to remove SNAP
by shifting addresses 6 bytes. This involves data copying, so
this feature should be disabled unless required by the platform.

Module parameter "rx_align_2" (bool, default - false)
introduced to control this feature. Feature is completely disabled
when parameter is false.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use temporal variable for often used vring->swhead;
and use proper index in debug printing - vring->swhead
used before was modified in wil_vring_advance_head
and then increased value was used in debug print
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>