PowerPC always re-builds DTB even if nothing has been changed.

As for other architectures, arch/*/boot/dts/Makefile builds DTB by
using the dtb-y syntax.

In contrast, arch/powerpc/boot/dts/(fsl/)Makefile does nothing unless
CONFIG_OF_ALL_DTBS is defined. Instead, arch/powerpc/boot/Makefile
builds DTB on demand. You need to add DTB to 'targets' explicitly
so .*.cmd files are included.
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>

Make 'make tar-pkg' install dtbs.
Signed-off-by: NDomenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>

Some Makefiles already pass -ffreestanding unconditionally.
For example, arch/arm64/lib/Makefile, arch/x86/purgatory/Makefile.

No problem report so far about hard-coding this option. So, we can
assume all supported compilers know -ffreestanding.

I confirmed GCC 4.8 and Clang manuals document this option.

Get rid of cc-option from -ffreestanding.
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>
Reviewed-by: NKees Cook <keescook@chromium.org>
Acked-by: NArd Biesheuvel <ardb@kernel.org>

Some Makefiles already pass -fno-stack-protector unconditionally.
For example, arch/arm64/kernel/vdso/Makefile, arch/x86/xen/Makefile.

No problem report so far about hard-coding this option. So, we can
assume all supported compilers know -fno-stack-protector.

GCC 4.8 and Clang support this option (https://godbolt.org/z/_HDGzN)

Get rid of cc-option from -fno-stack-protector.

Remove CONFIG_CC_HAS_STACKPROTECTOR_NONE, which is always 'y'.

Note:
arch/mips/vdso/Makefile adds -fno-stack-protector twice, first
unconditionally, and second conditionally. I removed the second one.
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>
Reviewed-by: NKees Cook <keescook@chromium.org>
Acked-by: NArd Biesheuvel <ardb@kernel.org>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>

This reverts commit 77479b38.

Since commit 8a78756e ("kbuild: create object directories simpler
and faster"), all directories for 'targets' are created.

'mkdir -p $(dir ${dtc-tmp})' is no longer needed.
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>

Since the pre-git time the checker is run first, before the compiler.
But if the source file contains some syntax error, the warnings from
the compiler are more useful than those from sparse (and other
checker most probably too).

So move the 'check' command to run after the compiler.
Signed-off-by: NLuc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>

Using a mutex for "print this warning only once" is so overdesigned as
to be actively offensive to my sensitive stomach.

Just use "pr_info_once()" that already does this, although in a
(harmlessly) racy manner that can in theory cause the message to be
printed twice if more than one CPU races on that "is this the first
time" test.

[ If somebody really cares about that harmless data race (which sounds
  very unlikely indeed), that person can trivially fix printk_once() by
  using a simple atomic access, preferably with an optimistic non-atomic
  test first before even bothering to treat the pointless "make sure it
  is _really_ just once" case.

  A mutex is most definitely never the right primitive to use for
  something like this. ]

Yes, this is a small and meaningless detail in a code path that hardly
matters.  But let's keep some code quality standards here, and not
accept outrageously bad code.

Link: https://lore.kernel.org/lkml/CAHk-=wgV9toS7GU3KmNpj8hCS9SeF+A0voHS8F275_mgLhL4Lw@mail.gmail.com/
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Thomas Gleixner:
 "A series of fixes for x86:

   - Reset MXCSR in kernel_fpu_begin() to prevent using a stale user
     space value.

   - Prevent writing MSR_TEST_CTRL on CPUs which are not explicitly
     whitelisted for split lock detection. Some CPUs which do not
     support it crash even when the MSR is written to 0 which is the
     default value.

   - Fix the XEN PV fallout of the entry code rework

   - Fix the 32bit fallout of the entry code rework

   - Add more selftests to ensure that these entry problems don't come
     back.

   - Disable 16 bit segments on XEN PV. It's not supported because XEN
     PV does not implement ESPFIX64"

* tag 'x86-urgent-2020-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ldt: Disable 16-bit segments on Xen PV
  x86/entry/32: Fix #MC and #DB wiring on x86_32
  x86/entry/xen: Route #DB correctly on Xen PV
  x86/entry, selftests: Further improve user entry sanity checks
  x86/entry/compat: Clear RAX high bits on Xen PV SYSENTER
  selftests/x86: Consolidate and fix get/set_eflags() helpers
  selftests/x86/syscall_nt: Clear weird flags after each test
  selftests/x86/syscall_nt: Add more flag combinations
  x86/entry/64/compat: Fix Xen PV SYSENTER frame setup
  x86/entry: Move SYSENTER's regs->sp and regs->flags fixups into C
  x86/entry: Assert that syscalls are on the right stack
  x86/split_lock: Don't write MSR_TEST_CTRL on CPUs that aren't whitelisted
  x86/fpu: Reset MXCSR to default in kernel_fpu_begin()

Pull irq fixes from Thomas Gleixner:
 "A set of interrupt chip driver fixes:

   - Ensure the atomicity of affinity updates in the GIC driver

   - Don't try to sleep in atomic context when waiting for the GICv4.1
     to respond. Use polling instead.

   - Typo fixes in Kconfig and warnings"

* tag 'irq-urgent-2020-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic: Atomically update affinity
  irqchip/riscv-intc: Fix a typo in a pr_warn()
  irqchip/gic-v4.1: Use readx_poll_timeout_atomic() to fix sleep in atomic
  irqchip/loongson-pci-msi: Fix a typo in Kconfig

Pull rcu fixlet from Thomas Gleixner:
 "A single fix for a printk format warning in RCU"

* tag 'core-urgent-2020-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcuperf: Fix printk format warning

Merge tag 'kbuild-fixes-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes frin Masahiro Yamada:

 - fix various bugs in xconfig

 - fix some issues in cross-compilation using Clang

 - fix documentation

* tag 'kbuild-fixes-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  .gitignore: Do not track `defconfig` from `make savedefconfig`
  kbuild: make Clang build userprogs for target architecture
  kbuild: fix CONFIG_CC_CAN_LINK(_STATIC) for cross-compilation with Clang
  kconfig: qconf: parse newer types at debug info
  kconfig: qconf: navigate menus on hyperlinks
  kconfig: qconf: don't show goback button on splitMode
  kconfig: qconf: simplify the goBack() logic
  kconfig: qconf: re-implement setSelected()
  kconfig: qconf: make debug links work again
  kconfig: qconf: make search fully work again on split mode
  kconfig: qconf: cleanup includes
  docs: kbuild: fix ReST formatting
  gcc-plugins: fix gcc-plugins directory path in documentation

Pull SCSI fixes from James Bottomley:
 "Four small fixes in three drivers.

  The mptfusion one has actually caused user visible issues in certain
  kernel configurations"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: mptfusion: Don't use GFP_ATOMIC for larger DMA allocations
  scsi: libfc: Skip additional kref updating work event
  scsi: libfc: Handling of extra kref
  scsi: qla2xxx: Fix a condition in qla2x00_find_all_fabric_devs()

Pull block fixes from Jens Axboe:

 - NVMe fixes from Christoph:
    - Fix crash in multi-path disk add (Christoph)
    - Fix ignore of identify error (Sagi)

 - Fix a compiler complaint that a function should be static (Wei)

* tag 'block-5.8-2020-07-05' of git://git.kernel.dk/linux-block:
  block: make function __bio_integrity_free() static
  nvme: fix a crash in nvme_mpath_add_disk
  nvme: fix identify error status silent ignore

Pull io_uring fix from Jens Axboe:
 "Andres reported a regression with the fix that was merged earlier this
  week, where his setup of using signals to interrupt io_uring CQ waits
  no longer worked correctly.

  Fix this, and also limit our use of TWA_SIGNAL to the case where we
  need it, and continue using TWA_RESUME for task_work as before.

  Since the original is marked for 5.7 stable, let's flush this one out
  early"

* tag 'io_uring-5.8-2020-07-05' of git://git.kernel.dk/linux-block:
  io_uring: fix regression with always ignoring signals in io_cqring_wait()

Pull i2c fixes from Wolfram Sang:
 "The usual driver fixes and documentation updates"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mlxcpld: check correct size of maximum RECV_LEN packet
  i2c: add Kconfig help text for slave mode
  i2c: slave-eeprom: update documentation
  i2c: eg20t: Load module automatically if ID matches
  i2c: designware: platdrv: Set class based on DMI
  i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665

Pull MIPS fixes from Thomas Bogendoerfer:

 - fix for missing hazard barrier

 - DT fix for ingenic

 - DT fix of GPHY names for lantiq

 - fix usage of smp_processor_id() while preemption is enabled

* tag 'mips_fixes_5.8_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: Do not use smp_processor_id() in preemptible code
  MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen
  MIPS: ingenic: gcw0: Fix HP detection GPIO.
  MIPS: lantiq: xway: sysctrl: fix the GPHY clock alias names

Use preempt_disable() to fix the following bug under CONFIG_DEBUG_PREEMPT.

[   21.915305] BUG: using smp_processor_id() in preemptible [00000000] code: qemu-system-mip/1056
[   21.923996] caller is do_ri+0x1d4/0x690
[   21.927921] CPU: 0 PID: 1056 Comm: qemu-system-mip Not tainted 5.8.0-rc2 #3
[   21.934913] Stack : 0000000000000001 ffffffff81370000 ffffffff8071cd60 a80f926d5ac95694
[   21.942984]         a80f926d5ac95694 0000000000000000 98000007f0043c88 ffffffff80f2fe40
[   21.951054]         0000000000000000 0000000000000000 0000000000000001 0000000000000000
[   21.959123]         ffffffff802d60cc 98000007f0043dd8 ffffffff81f4b1e8 ffffffff81f60000
[   21.967192]         ffffffff81f60000 ffffffff80fe0000 ffff000000000000 0000000000000000
[   21.975261]         fffffffff500cce1 0000000000000001 0000000000000002 0000000000000000
[   21.983331]         ffffffff80fe1a40 0000000000000006 ffffffff8077f940 0000000000000000
[   21.991401]         ffffffff81460000 98000007f0040000 98000007f0043c80 000000fffba8cf20
[   21.999471]         ffffffff8071cd60 0000000000000000 0000000000000000 0000000000000000
[   22.007541]         0000000000000000 0000000000000000 ffffffff80212ab4 a80f926d5ac95694
[   22.015610]         ...
[   22.018086] Call Trace:
[   22.020562] [<ffffffff80212ab4>] show_stack+0xa4/0x138
[   22.025732] [<ffffffff8071cd60>] dump_stack+0xf0/0x150
[   22.030903] [<ffffffff80c73f5c>] check_preemption_disabled+0xf4/0x100
[   22.037375] [<ffffffff80213b84>] do_ri+0x1d4/0x690
[   22.042198] [<ffffffff8020b828>] handle_ri_int+0x44/0x5c
[   24.359386] BUG: using smp_processor_id() in preemptible [00000000] code: qemu-system-mip/1072
[   24.368204] caller is do_ri+0x1a8/0x690
[   24.372169] CPU: 4 PID: 1072 Comm: qemu-system-mip Not tainted 5.8.0-rc2 #3
[   24.379170] Stack : 0000000000000001 ffffffff81370000 ffffffff8071cd60 a80f926d5ac95694
[   24.387246]         a80f926d5ac95694 0000000000000000 98001007ef06bc88 ffffffff80f2fe40
[   24.395318]         0000000000000000 0000000000000000 0000000000000001 0000000000000000
[   24.403389]         ffffffff802d60cc 98001007ef06bdd8 ffffffff81f4b818 ffffffff81f60000
[   24.411461]         ffffffff81f60000 ffffffff80fe0000 ffff000000000000 0000000000000000
[   24.419533]         fffffffff500cce1 0000000000000001 0000000000000002 0000000000000000
[   24.427603]         ffffffff80fe0000 0000000000000006 ffffffff8077f940 0000000000000020
[   24.435673]         ffffffff81460020 98001007ef068000 98001007ef06bc80 000000fffbbbb370
[   24.443745]         ffffffff8071cd60 0000000000000000 0000000000000000 0000000000000000
[   24.451816]         0000000000000000 0000000000000000 ffffffff80212ab4 a80f926d5ac95694
[   24.459887]         ...
[   24.462367] Call Trace:
[   24.464846] [<ffffffff80212ab4>] show_stack+0xa4/0x138
[   24.470029] [<ffffffff8071cd60>] dump_stack+0xf0/0x150
[   24.475208] [<ffffffff80c73f5c>] check_preemption_disabled+0xf4/0x100
[   24.481682] [<ffffffff80213b58>] do_ri+0x1a8/0x690
[   24.486509] [<ffffffff8020b828>] handle_ri_int+0x44/0x5c
Signed-off-by: NXingxing Su <suxingxing@loongson.cn>
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>

This resolves the hazard between the mtc0 in the change_c0_status() and
the mfc0 in configure_exception_vector(). Without resolving this hazard
configure_exception_vector() could read an old value and would restore
this old value again. This would revert the changes change_c0_status()
did. I checked this by printing out the read_c0_status() at the end of
per_cpu_trap_init() and the ST0_MX is not set without this patch.

The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:

   Producer | Consumer | Hazard
  ----------|----------|----------------------------
   mtc0     | mfc0     | any coprocessor 0 register

I saw this hazard on an Atheros AR9344 rev 2 SoC with a MIPS 74Kc CPU.
There the change_c0_status() function would activate the DSPen by
setting ST0_MX in the c0_status register. This was reverted and then the
system got a DSP exception when the DSP registers were saved in
save_dsp() in the first process switch. The crash looks like this:

[    0.089999] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097796] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.107070] Kernel panic - not syncing: Unexpected DSP exception
[    0.113470] Rebooting in 1 seconds..

We saw this problem in OpenWrt only on the MIPS 74Kc based Atheros SoCs,
not on the 24Kc based SoCs. We only saw it with kernel 5.4 not with
kernel 4.19, in addition we had to use GCC 8.4 or 9.X, with GCC 8.3 it
did not happen.

In the kernel I bisected this problem to commit 9012d011 ("compiler:
allow all arches to enable CONFIG_OPTIMIZE_INLINING"), but when this was
reverted it also happened after commit 172dcd93 ("MIPS: Always
allocate exception vector for MIPSr2+").

Commit 0b24cae4 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
does similar changes to a different file. I am not sure if there are
more places affected by this problem.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>

Running `make savedefconfig` creates by default `defconfig`, which is,
currently, on git’s radar, for example, `git status` lists this file as
untracked.

So, add the file to `.gitignore`, so it’s ignored by git.
Signed-off-by: NPaul Menzel <pmenzel@molgen.mpg.de>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>

Pull powerpc fixes from Michael Ellerman:
 "One fix for a regression in our pkey handling, which exhibits as
  PROT_EXEC mappings taking continuous page faults.

  Thanks to: Jan Stancek, Aneesh Kumar K.V"

* tag 'powerpc-5.8-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm/pkeys: Make pkey access check work on execute_only_key

Pull arm64 fixes from Will Deacon:
 "Nothing earth-shattering, really - some CPU errata workarounds (one
  day they'll get it right, ha!) and a fix for a boot failure with very
  large kernel images where the alternative patching gets confused when
  patching relative branches using veneers.

   - Fix alternative patching for very large kernel images and modules

   - Hook up existing CPU errata workarounds for Qualcomm Kryo CPUs"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Add KRYO4XX silver CPU cores to erratum list 1530923 and 1024718
  arm64: Add KRYO4XX gold CPU cores to erratum list 1463225 and 1418040
  arm64: Add MIDR value for KRYO4XX gold CPU cores
  arm64/alternatives: use subsections for replacement sequences

When switching to TWA_SIGNAL for task_work notifications, we also made
any signal based condition in io_cqring_wait() return -ERESTARTSYS.
This breaks applications that rely on using signals to abort someone
waiting for events.

Check if we have a signal pending because of queued task_work, and
repeat the signal check once we've run the task_work. This provides a
reliable way of telling the two apart.

Additionally, only use TWA_SIGNAL if we are using an eventfd. If not,
we don't have the dependency situation described in the original commit,
and we can get by with just using TWA_RESUME like we previously did.

Fixes: ce593a6c ("io_uring: use signal based task_work running")
Cc: stable@vger.kernel.org # v5.7
Reported-by: NAndres Freund <andres@anarazel.de>
Tested-by: NAndres Freund <andres@anarazel.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Xen PV doesn't implement ESPFIX64, so they don't work right.  Disable
them.  Also print a warning the first time anyone tries to use a
16-bit segment on a Xen PV guest that would otherwise allow it
to help people diagnose this change in behavior.

This gets us closer to having all x86 selftests pass on Xen PV.
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/92b2975459dfe5929ecf34c3896ad920bd9e3f2d.1593795633.git.luto@kernel.org

DEFINE_IDTENTRY_MCE and DEFINE_IDTENTRY_DEBUG were wired up as non-RAW
on x86_32, but the code expected them to be RAW.

Get rid of all the macro indirection for them on 32-bit and just use
DECLARE_IDTENTRY_RAW and DEFINE_IDTENTRY_RAW directly.

Also add a warning to make sure that we only hit the _kernel paths
in kernel mode.
Reported-by: NNaresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/9e90a7ee8e72fd757db6d92e1e5ff16339c1ecf9.1593795633.git.luto@kernel.org

On Xen PV, #DB doesn't use IST. It still needs to be correctly routed
depending on whether it came from user or kernel mode.

Get rid of DECLARE/DEFINE_IDTENTRY_XEN -- it was too hard to follow the
logic.  Instead, route #DB and NMI through DECLARE/DEFINE_IDTENTRY_RAW on
Xen, and do the right thing for #DB.  Also add more warnings to the
exc_debug* handlers to make this type of failure more obvious.

This fixes various forms of corruption that happen when usermode
triggers #DB on Xen PV.

Fixes: 4c0dcd83 ("x86/entry: Implement user mode C entry points for #DB and #MCE")
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/4163e733cce0b41658e252c6c6b3464f33fdff17.1593795633.git.luto@kernel.org

Chasing down a Xen bug caused me to realize that the new entry sanity
checks are still fairly weak.  Add some more checks.
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/881de09e786ab93ce56ee4a2437ba2c308afe7a9.1593795633.git.luto@kernel.org

Move the clearing of the high bits of RAX after Xen PV joins the SYSENTER
path so that Xen PV doesn't skip it.

Arguably this code should be deleted instead, but that would belong in the
merge window.

Fixes: ffae641f ("x86/entry/64/compat: Fix Xen PV SYSENTER frame setup")
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/9d33b3f3216dcab008070f1c28b6091ae7199969.1593795633.git.luto@kernel.org

Pull xen fixes from Juergen Gross:
 "One small cleanup patch for ARM and two patches for the xenbus driver
  fixing latent problems (large stack allocations and bad return code
  settings)"

* tag 'for-linus-5.8b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/xenbus: let xenbus_map_ring_valloc() return errno values only
  xen/xenbus: avoid large structs and arrays on the stack
  arm/xen: remove the unused macro GRANT_TABLE_PHYSADDR

I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno
to what is suggested for this error.

Fixes: c9bfdc7c ("i2c: mlxcpld: Add support for smbus block read transaction")
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NMichael Shych <michaelsh@mellanox.com>
Tested-by: NMichael Shych <michaelsh@mellanox.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

Pull sysctl fix from Al Viro:
 "Another regression fix for sysctl changes this cycle..."

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Call sysctl_head_finish on error

I can't recall why there was none, but we surely want to have it.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

Add more details which have either been missing ever since or describe
recent additions.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NLuca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

Current AMD's zen-based APUs use this core for some of its i2c-buses.

With this patch we re-enable autodetection of hwmon-alike devices, so
lm-sensors will be able to work automatically.

It does not affect the boot-time of embedded devices, as the class is
set based on the DMI information.

DMI is probed only on Qtechnology QT5222 Industrial Camera Platform.

DocLink: https://qtec.com/camera-technology-camera-platforms/
Fixes: 3eddad96 ("i2c: designware: reverts "i2c: designware: Add support for AMD I2C controller"")
Signed-off-by: NRicardo Ribalda <ribalda@kernel.org>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.

Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.

Fixes: eff9ec95 ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

Pull cifs fixes from Steve French:
 "Eight cifs/smb3 fixes, most when specifying the multiuser mount flag.

  Five of the fixes are for stable"

* tag '5.8-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: prevent truncation from long to int in wait_for_free_credits
  cifs: Fix the target file was deleted when rename failed.
  SMB3: Honor 'posix' flag for multiuser mounts
  SMB3: Honor 'handletimeout' flag for multiuser mounts
  SMB3: Honor lease disabling for multiuser mounts
  SMB3: Honor persistent/resilient handle flags for multiuser mounts
  SMB3: Honor 'seal' flag for multiuser mounts
  cifs: Display local UID details for SMB sessions in DebugData

Merge tag 'hwmon-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Fix typo in Kconfig SENSORS_IR35221 option

 - Fix potential memory leak in acpi_power_meter_add()

 - Make sure the OVERT mask is set correctly in max6697 driver

 - In PMBus core, fix page vs. register when accessing fans

 - Mark is_visible functions static in bt1-pvt driver

 - Define Temp- and Volt-to-N poly as maybe-unused in bt1-pvt driver

* tag 'hwmon-for-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (pmbus) fix a typo in Kconfig SENSORS_IR35221 option
  hwmon: (acpi_power_meter) Fix potential memory leak in acpi_power_meter_add()
  hwmon: (max6697) Make sure the OVERT mask is set correctly
  hwmon: (pmbus) Fix page vs. register when accessing fans
  hwmon: (bt1-pvt) Mark is_visible functions static
  hwmon: (bt1-pvt) Define Temp- and Volt-to-N poly as maybe-unused

Merge misc fixes from Andrew Morton:
 "Subsystems affected by this patch series: mm/hugetlb, samples, mm/cma,
  mm/vmalloc, mm/pagealloc"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/page_alloc: fix documentation error
  vmalloc: fix the owner argument for the new __vmalloc_node_range callers
  mm/cma.c: use exact_nid true to fix possible per-numa cma leak
  samples/vfs: avoid warning in statx override
  mm/hugetlb.c: fix pages per hugetlb calculation

When I increased the upper bound of the min_free_kbytes value in
ee8eb9a5 ("mm/page_alloc: increase default min_free_kbytes bound") I
forgot to tweak the above comment to reflect the new value.  This patch
fixes that mistake.
Signed-off-by: NJoel Savitz <jsavitz@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Fabrizio D'Angelo <fdangelo@redhat.com>
Link: http://lkml.kernel.org/r/20200624221236.29560-1-jsavitz@redhat.comSigned-off-by: NLinus Torvalds <torvalds@linux-foundation.org>