We introduced a new lock here, so there was error path which needs
an unlock now.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
This patch contains additional structure and function definition changes
that are required to enable the new msgq/enet/txrx redesign introduced
by the previous 4 patches.
 - structure and function definition changes to header files as a result
   of Ethport, Enet, IOCEth, Tx, Rx redesign.
 - ethtool changes to use new enet function and definitions
 - Set number of Tx and Rx queues bassed on underlying hardware. Define
   separate macros for maximum and supported numbers of Tx and Rx queues
   based on underlying hardware. Take VLAN header into account for MTU
   calculation. Default to INTx mode when pci_enable_msix() fails. Set a
   bit in Rx poll routine, check and wait for that bit to be cleared in
   the cleanup routine before proceeding.
 - The TX and Rx coalesce settings are programmed in steps of 5 us. The value
   that are not divisible by 5 are rounded to the next lower number. This was
   causing the value os 1 to 4 to be rounded to 0, which is an invalid setting.
   When creating Rx and Tx object, we are currently assigning the default
   values of Rx and Tx coalescing_timeo. If these values are changed in the
   driver to a different value, the change is lost during such operations as
   MTU change. In order to avoid that, pass the configured value of
   coalescing_timeo before Rx and Tx object creation. Fix
   bnad_tx_coalescing_timeo_set() so it applies to all the Tx objects.
 - Reorg uninitialization path in case of pci_probe failure.
 - Hardware clock setup changes to pass asic generation, port modes and
   asic mode as part firmware boot parameters to firmware.
 - FW mailbox interface changes to defined asic specific mailbox interfaces.
   h/w mailbox interfaces take 8-bit FIDs and 2-bit port id for owner. Cleaned
   up mailbox definitions and usage for new and old HW. Eliminated usage of
   ASIC ID. MSI-X vector assignment and programming done by firmware. Fixed
   host offsets for CPE/RME queue registers.
 - Implement polling mechanism for FW ready to have poll mechanism replaces
   the current interrupt based FW READY method. The timer based poll routine
   in IOC will query the ioc_fwstate register to see if there is a state
   change in FW, and sends the READY event. Removed infrastructure needed to
   support mbox READY event from fw as well as IOC code.
 - Move FW init to HW init. Handle the case where PCI mapping goes away when
   IOCPF state machine is waiting for semaphore.
 - Add IOC mbox call back to client indicating that the command is sent.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Brocade driver into drivers/net/ethernet/brocade/ and make
the necessary Kconfig and Makefile changes.

CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove duplicated #include('s) in
  drivers/net/bna/bnad.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Always set mbox irq index to zero and make corresponding changes in mbox
   irq alloc/sync function and txrx irq index calculation. Add definition of
   BNAD_INTX_TX_IB_BITMASK & BNAD_INTX_RX_IB_BITMASK and update
   bnad_txrx_irq_alloc accordingly.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Driver cleanup as per new checkpatch v0.31
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Print the dirver version when module is loaded.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- unify vlan and nonvlan rx path
- kill bnad->vlan_grp and bnad_vlan_rx_register
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 5f77898d does not completely
fix the problem of handling allocations with irqs disabled..  The
below patch on top of it fixes the problem completely.

Based on review by "Ivan Vecera" <ivecera@redhat.com>..
"
Small note, the root of the problem was that non-atomic allocation was requested with IRQs disabled. Your patch description does not contain wwhy were the IRQs disabled.

The function bnad_mbox_irq_alloc incorrectly uses 'flags' var for two different things, 1) to save current CPU flags and 2) for request_irq
call.
First the spin_lock_irqsave disables the IRQs and saves _all_ CPU flags (including one that enables/disables interrupts) to 'flags'. Then the 'flags' is overwritten by 0 or 0x80 (IRQF_SHARED). Finally the spin_unlock_irqrestore should restore saved flags, but these flags are now either 0x00 or 0x80. The interrupt bit value in flags register on x86 arch is 0x100.
This means that the interrupt bit is zero (IRQs disabled) after spin_unlock_irqrestore so the request_irq function is called with disabled interrupts.
"
Signed-off-by: NShyam Iyer <shyam_iyer@dell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some workloads need some headroom (NET_SKB_PAD) to avoid expensive
reallocations.

Using netdev_alloc_skb_ip_align() instead of bare skb_alloc() brings the
NET_IP_ALIGN and the NET_SKB_PAD headroom.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

request_threaded irq will call kzalloc that can sleep. Initializing the flags variable outside of spin_lock_irqsave/restore in bnad_mbox_irq_alloc will avoid call traces like below.

Jun 27 08:15:24 home-t710 kernel: [11735.634550] Brocade 10G Ethernet driver
Jun 27 08:15:24 home-t710 kernel: [11735.634590] bnad_pci_probe : (0xffff880427f3d000, 0xffffffffa020f3e0) PCI Func : (2)
Jun 27 08:15:24 home-t710 kernel: [11735.637677] bna 0000:82:00.2: PCI INT A -> GSI 66 (level, low) -> IRQ 66
Jun 27 08:15:24 home-t710 kernel: [11735.638290] bar0 mapped to ffffc90014980000, len 262144
Jun 27 08:15:24 home-t710 kernel: [11735.638732] BUG: sleeping function called from invalid context at mm/slub.c:847
Jun 27 08:15:24 home-t710 kernel: [11735.638736] in_atomic(): 0, irqs_disabled(): 1, pid: 11243, name: insmod
Jun 27 08:15:24 home-t710 kernel: [11735.638740] Pid: 11243, comm: insmod Not tainted 3.0.0-rc4+ #6
Jun 27 08:15:24 home-t710 kernel: [11735.638743] Call Trace:
Jun 27 08:15:24 home-t710 kernel: [11735.638755]  [<ffffffff81046427>] __might_sleep+0xeb/0xf0
Jun 27 08:15:24 home-t710 kernel: [11735.638766]  [<ffffffffa01fe469>] ? netif_wake_queue+0x3d/0x3d [bna]
Jun 27 08:15:24 home-t710 kernel: [11735.638773]  [<ffffffff8111201c>] kmem_cache_alloc_trace+0x43/0xd8
Jun 27 08:15:24 home-t710 kernel: [11735.638782]  [<ffffffffa01fe469>] ? netif_wake_queue+0x3d/0x3d [bna]
Jun 27 08:15:24 home-t710 kernel: [11735.638787]  [<ffffffff810ab791>] request_threaded_irq+0xa1/0x113
Jun 27 08:15:24 home-t710 kernel: [11735.638798]  [<ffffffffa020f0c0>] bnad_pci_probe+0x612/0x8e5 [bna]
Jun 27 08:15:24 home-t710 kernel: [11735.638807]  [<ffffffffa01fe469>] ? netif_wake_queue+0x3d/0x3d [bna]
Jun 27 08:15:24 home-t710 kernel: [11735.638816]  [<ffffffff81482ef4>] ? _raw_spin_unlock_irqrestore+0x17/0x19
Jun 27 08:15:24 home-t710 kernel: [11735.638822]  [<ffffffff8124d17a>] local_pci_probe+0x44/0x75
Jun 27 08:15:24 home-t710 kernel: [11735.638826]  [<ffffffff8124dc06>] pci_device_probe+0xd0/0xff
Jun 27 08:15:24 home-t710 kernel: [11735.638832]  [<ffffffff812ef8ab>] driver_probe_device+0x131/0x213
Jun 27 08:15:24 home-t710 kernel: [11735.638836]  [<ffffffff812ef9e7>] __driver_attach+0x5a/0x7e
Jun 27 08:15:24 home-t710 kernel: [11735.638840]  [<ffffffff812ef98d>] ? driver_probe_device+0x213/0x213
Jun 27 08:15:24 home-t710 kernel: [11735.638844]  [<ffffffff812ee933>] bus_for_each_dev+0x53/0x89
Jun 27 08:15:24 home-t710 kernel: [11735.638848]  [<ffffffff812ef48a>] driver_attach+0x1e/0x20
Jun 27 08:15:24 home-t710 kernel: [11735.638852]  [<ffffffff812ef0ae>] bus_add_driver+0xd1/0x224
Jun 27 08:15:24 home-t710 kernel: [11735.638858]  [<ffffffffa01b8000>] ? 0xffffffffa01b7fff
Jun 27 08:15:24 home-t710 kernel: [11735.638862]  [<ffffffff812efe57>] driver_register+0x98/0x105
Jun 27 08:15:24 home-t710 kernel: [11735.638866]  [<ffffffffa01b8000>] ? 0xffffffffa01b7fff
Jun 27 08:15:24 home-t710 kernel: [11735.638871]  [<ffffffff8124e4c9>] __pci_register_driver+0x56/0xc1
Jun 27 08:15:24 home-t710 kernel: [11735.638875]  [<ffffffffa01b8000>] ? 0xffffffffa01b7fff
Jun 27 08:15:24 home-t710 kernel: [11735.638884]  [<ffffffffa01b8040>] bnad_module_init+0x40/0x60 [bna]
Jun 27 08:15:24 home-t710 kernel: [11735.638892]  [<ffffffff81002099>] do_one_initcall+0x7f/0x136
Jun 27 08:15:24 home-t710 kernel: [11735.638899]  [<ffffffff8108608b>] sys_init_module+0x88/0x1d0
Jun 27 08:15:24 home-t710 kernel: [11735.638906]  [<ffffffff81489682>] system_call_fastpath+0x16/0x1b
Jun 27 08:15:24 home-t710 kernel: [11735.639642] bnad_pci_probe : (0xffff880427f3e000, 0xffffffffa020f3e0) PCI Func : (3)
Jun 27 08:15:24 home-t710 kernel: [11735.639665] bna 0000:82:00.3: PCI INT A -> GSI 66 (level, low) -> IRQ 66
Jun 27 08:15:24 home-t710 kernel: [11735.639735] bar0 mapped to ffffc90014400000, len 262144
Signed-off-by: NShyam Iyer <shyam_iyer@dell.com>
Acked-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout.  Give
them an explicit include via the following $0.02 script.

 =========================================
 #!/bin/bash
 MANUAL=""
 for i in `git grep -l 'prefetch(.*)' .` ; do
 	grep -q '<linux/prefetch.h>' $i
 	if [ $? = 0 ] ; then
 		continue
 	fi

 	(	echo '?^#include <linux/?a'
 		echo '#include <linux/prefetch.h>'
 		echo .
 		echo w
 		echo q
 	) | ed -s $i > /dev/null 2>&1
 	if [ $? != 0 ]; then
 		echo $i needs manual fixup
 		MANUAL="$i $MANUAL"
 	fi
 done
 echo ------------------- 8\<----------------------
 echo vi $MANUAL
 =========================================
Signed-off-by: NPaul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
  non-network drivers and the fib_trie.c case    - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout.  Give
them an explicit include via the following $0.02 script.

 =========================================
 #!/bin/bash
 MANUAL=""
 for i in `git grep -l 'prefetch(.*)' .` ; do
 	grep -q '<linux/prefetch.h>' $i
 	if [ $? = 0 ] ; then
 		continue
 	fi

 	(	echo '?^#include <linux/?a'
 		echo '#include <linux/prefetch.h>'
 		echo .
 		echo w
 		echo q
 	) | ed -s $i > /dev/null 2>&1
 	if [ $? != 0 ]; then
 		echo $i needs manual fixup
 		MANUAL="$i $MANUAL"
 	fi
 done
 echo ------------------- 8\<----------------------
 echo vi $MANUAL
 =========================================
Signed-off-by: NPaul <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The memory leak was caused by unintentional assignment of the Rx path
destroy callback function pointer to NULL just after correct
initialization.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note: looks like bnad->conf_mutex is duplicating rtnl_lock.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DMA API as PCI equivalents will be deprecated.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Made IOC auto_recovery synchronized and not timer based.
	- Only one PCI function will attempt to recover and reinitialize
	the ASIC on a failure, that too after all the active PCI
	functions acknowledge the IOC failure.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Retrieve the VLAN configuration from the networking stack
	and apply it to the base interface during ifconfig up
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Call netif_wake_queue() if we have freed up sufficient elements
	at the end of completion processing
	- Add netif_queue_stopped counter back to bnad_drv_stats {}
	- Get netif_queue_stopped value from stack
	- Remove BUG_ON() on value returned by pci_unmap_addr()
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Removed semaphore register dump from ethtool
	- Moved netif_carrier_off() call to before calling bna_init()
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Check HW ready condition before accessing h/w register in data-path
	- Postpone clean-up of data buffers to the data-path restart path and
	wait in the cleanup routines for in-flight DMA to complete
	- Separate out Tx completion processing from Rx poll routine
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb.  There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances.  However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by Stephen Hemminger:
1) Made functions and data structures static wherever possible.
2) Removed unused code.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fix handles the case when IRQ handler is called (for shared IRQs)
even before the driver is ready to handle interrupts.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnad_set_rx_mode omit to unlock bna_lock on one fail path. Fix that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Debashis Dutt <ddutt@brocade.com>
Cc: Rasesh Mody <rmody@brocade.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fresh skbs have ip_summed set to CHECKSUM_NONE (0)

We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.

Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.

Change most occurrences of :

skb->ip_summed = CHECKSUM_NONE;

by :

skb_checksum_none_assert(skb);
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

get_stats() method incorrectly clears a global array before folding
various stats. This can break SNMP applications.

Switch to 64 bit flavor to work on a user supplied buffer, and provide
64bit counters even on 32bit arches.

Fix a bug in bnad_netdev_hwstats_fill(), for rx_fifo_errors, missing a
folding (only the last counter was taken into account)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the patch to fix the build break caused by multiple
definitions of symbols between Brocade's FC/FCOE driver(BFA)
and 10G Networking Driver(BNA).

Changes are:

1. locally used functions are made static 

2. unused functions are removed

3. using unique namespaces for the function names that must be
globally visible
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is patch 1/6 which contains linux driver source for
Brocade's BR1010/BR1020 10Gb CEE capable ethernet adapter.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>