Reviewed-by: NArun Parameswaran <aparames@broadcom.com>
Tested-by: NJonathan Richardson <jonathar@broadcom.com>
Reviewed-by: NJD (Jiandong) Zheng <jdzheng@broadcom.com>
Reviewed-by: NRay Jui <rjui@broadcom.com>
Signed-off-by: NScott Branden <sbranden@broadcom.com>

Document the device-tree binding of Marvell PXA based SoCs.
PXA clocks are mostly fixed rate and fixed ratio clocks derived from an
external oscillator, and gated by a register set (CKEN or CKEN*).
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The MBUS clock on sun8i is slightly different from the old mod0 clocks.
The divider is 3 bits wider, while also needing a divider table for the
higher 4 values, which all set the same divider.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The MMC clock we thought we had until now are actually not one but three
different clocks.

The main one is unchanged, and will have three outputs:
  - The clock fed into the MMC
  - a sample and output clocks, to deal with when should we output/sample data
    to/from the MMC bus

The phase control we had are actually controlling the two latter clocks, but
the main MMC one is unchanged.

We can adjust the phase with a 3 bits value, from 0 to 7, 0 meaning a 180 phase
shift, and the other values being the number of periods from the MMC parent
clock to outphase the clock of.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>

Even though the mbus clock is a regular module clock, given its nature, it
needs to be enabled all the time.

Introduce a new compatible, to differentiate it from the other module clocks.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>

The added gpio-gate-clock is a basic clock that can be enabled and
disabled trough a gpio output. The DT binding document for the clock
is also added. For EPROBE_DEFER handling the registering of the clock
has to be delayed until of_clk_get() call time.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Document the new compatible for clock in DMC (Dynamic Memory
Controller) domain of Exynos3250 Clock Management Unit (CMU).
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>

Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add Device Tree binding documentation for the clocks
outputs in the Maxim 77802 Power Management IC.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Like most clock drivers, the Maxim 77686 PMIC clock binding
follows the convention that the "#clock-cells" property is
used to specify the number of cells in a clock provider.

But the binding document is not clear enough that it shall
be set to 1 since the PMIC support multiple clocks outputs.

Also, explain that the clocks identifiers are defined in a
header file that can be included by Device Tree source with
client nodes to avoid using magic numbers.

Finally, add "clock-output-names" as an optional property
since now is supported by the clock driver.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Correct spelling typo in treewide.
Signed-off-by: NHayato Suzuki <hytszk@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch adds DT binding documentation for the Cirrus Logic
CLPS711X-based CPUs clock subsystem.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

A Flexgen structure is composed by:
- a clock cross bar (represented by a mux element)
- a pre and final dividers (represented by a divider and gate elements)
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Naming convention was changed in dts file but the
clock binding documentation hasn't been updated.
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch adds helper functions to configure clock parents and rates
as specified through 'assigned-clock-parents', 'assigned-clock-rates'
DT properties for a clock provider or clock consumer device.
The helpers are now being called by the bus code for the platform, I2C
and SPI busses, before the driver probing and also in the clock core
after registration of a clock provider.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch adds a driver for clock controller being a part of Audio
Subsystem present on S5PV210 and compatible SoCs. It is used to provide
clocks for other IP blocks of this subsystem.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds new, Common Clock Framework-based clock driver for Samsung
S5PV210 and compatible SoCs. The driver is just added, without enabling it yet.
Signed-off-by: NMateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
[t.figa: Added support for other SoC variants and clock output. Fixed
remaining minor issues.]
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Use clock defines in order to make devicetrees more human readable.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds devicetree support CCM module for i.MX21 CPUs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Instead of using enum for clock ID, let's switch imx6qdl clock driver to
use macro.  In this case, device tree can reuse these macros to improve
readability.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds devicetree support CCM module for i.MX1 (MC9328MX1) CPUs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This commit extends the existing clk-cpu driver used on Marvell Armada
XP platforms to support the dynamic frequency scaling of the CPU
clock. Non-dynamic frequency change was already supported (and used
before secondary CPUs are started), but the dynamic frequency change
requires a completely different procedure.

In order to achieve this, the clk_cpu_set_rate() function is reworked
to handle two separate cases:

 - The case where the clock is enabled, which is the new dynamic
   frequency change code, implemented in clk_cpu_on_set_rate(). This
   part will be used for cpufreq activities.

 - The case where the clock is disabled, which is the existing
   frequency change code, moved in clk_cpu_off_set_rate(). This part
   is already used to set the clock frequency of the secondary CPUs
   before starting them.

In order to implement the dynamic frequency change function, we need
to access the PMU DFS registers, which are outside the currently
mapped "Clock Complex" registers, so a new area of registers is now
mapped. This affects the Device Tree binding, but we are careful to do
it in a backward-compatible way (by allowing the second pair of
registers to be non-existent, and in this case, ensuring
clk_cpu_on_set_rate() returns an error).

Note that technically speaking, the clk_cpu_on_set_rate() does not do
the entire procedure needed to change the frequency dynamically, as it
involves touching a number of PMSU registers. This is done through a
clock notifier registered by the PMSU driver in followup commits.

Cc: <devicetree@vger.kernel.org>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404920715-19834-4-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The APQ8064 multimedia clock controller is fairly similar to the
8960 multimedia clock controller, except that gfx2d0/1 has been
removed and the gfx3d frequency is slightly faster when using the
newly introduced PLL15. We also add vcap clocks and a couple new
TV clocks.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Add a driver for the global clock controller found on IPQ8064 based
platforms. This should allow most non-multimedia device drivers to probe
and control their clocks.

This is currently missing clocks for USB HSIC and networking devices.
Signed-off-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Add support for the multimedia clock controller found on the APQ8084
based platforms. This will allow the multimedia device drivers to
control their clocks.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
[sboyd: Rework parent mapping to avoid conflicts]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

This patch adds "allwinner,sun8i-a23-apb0-gates-clk", a A23 specific
compatible to the sun6i-a31-apb0-gates clock driver, along with the
gate bitmap.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds the dt-binding documentation for the clock and reset unit found on
Rockchip rk3288 SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This add bindings documentation for the clock and reset unit found on
rk3188 and rk3066 SoCs from Rockchip.

Also deprecate the old gate clock binding, as these shouldn't be used
in the future.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add the compatible string for the APQ8084 global clock controller
to the clock binding documentation.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

The A23 has an almost identical PRCM clock tree. The difference in
the APB0 clock is the smallest divisor is 1, instead of 2.

This patch adds a separate sun8i-a23-apb0-clk driver to support it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The clock control unit on the A23 is similar to the one found on the A31.

The AHB1, APB1, APB2 gates on the A23 are almost identical to the ones
on the A31, but some outputs are missing.

The main CPU PLL (PLL1) however is like that on older Allwinner SoCs,
such as the A10 or A20, but the N factor starts from 1 instead of 0.

This patch adds support for PLL1 and all the basic clock muxes and gates.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Palmas class of devices can provide 32K clock(s) to be used by other devices
on the board. Depending on the actual device the provided clocks can be:
CLK32K_KG and CLK32K_KGAUDIO
or only one:
CLK32K_KG (TPS659039 for example)

Use separate compatible flags for the two 32K clock.
A system which needs or have only one of the 32k clock from
Palmas will need to add node(s) for each clock as separate section
in the dts file.
The two compatible property is:
"ti,palmas-clk32kg" for clk32kg clock
"ti,palmas-clk32kgaudio" for clk32kgaudio clock

Apart from the register control of the clocks - which is done via
the clock API there is a posibility to enable the external sleep
control. In this way the clock can be enabled/disabled on demand by the
user of the clock.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Document new compatible strings for clock provided by the PRCM
(Power/Reset/Clock Management) unit.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

Support for the USB gates and resets on A31 has been recently added
using a new compatible, so let's document it here.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

MPU DPLL on OMAP5, DRA75x, DRA72x has a limitation on the maximum
frequency it can be locked at. Duty Cycle Correction circuit is used
to recover a correct duty cycle for achieving higher frequencies
(hardware internally switches output to M3 output(CLKOUTHIF) from M2
output (CLKOUT)).

So provide support to setup required data to handle Duty cycle by
the setting up the minimum frequency for DPLL. 1.4GHz is common
for all these devices and is based on Technical Reference Manual
information for OMAP5432((SWPU282U) chapter 3.6.3.3.1 "DPLLs Output
Clocks Parameters", and equivalent information from DRA75x, DRA72x
documentation(SPRUHP2E, SPRUHI2P).
Signed-off-by: NNishanth Menon <nm@ti.com>
[t-kristo@ti.com: updated for latest dpll init API call]
Signed-off-by: NTero Kristo <t-kristo@ti.com>

The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: NTarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: NVyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>