Smatch shows the following warnings:

  CHECK   drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c +1315 ath9k_htc_configure_filter(27) warn: inconsistent returns mutex:&priv->mutex: locked (1303) unlocked (1315)

  CHECK   drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c +3321 ar9300_eeprom_restore_internal(20) warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.

Debugfs file location:
    <debugfs_mnt>/ieee80211/phy#/ath9k/samples
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent commit "ath9k: Send legacy rated frames as unaggregated"
introduced a check to ensure that packets with non-MCS rates set in
the rate series will not be aggregated. However, it failed to check
if the rate series is valid before testing the flags, thus breaking
aggregation for normal MCS-only packets if the last series is unset.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize 9us slot time as that is what is used mostly
(for non-ERP cases) and also to be in sync with initvals.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was tested on three BCM4331 devices, code has been written from MMIO
dumps only, but seems to be quite stable.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When 64-bit DMA was first used, there were problems with the
BCM4311 (14e4:4311). The problem was "fixed" by using the GFP_DMA
flag in the allocation of coherent ring descriptor memory.

The original problem is now believed to have been due to bugs in
the 64-bit DMA implementation in the rest of the kernel, and that
those bugs have been fixed. Accordingly, the requirement for the
descriptors to be in the DMA zone is relaxed.

Bounce buffers are left in the DMA zone.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since commit e0626e38 (spi: prefix modalias with "spi:"),
the spi modalias is prefixed with "spi:".

This patch adds "spi:" prefix for modalias of stlc45xx.
Also move it to be group with other modalias.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-By: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to implement support for GO powersave on
the P2P client side, the ucode needs to know what
GO we're trying to authenticate/associate with,
it needs to have a station entry and the BSSID in
the RXON set.

Implement the new mac80211 callbacks to give this
data to the device.

Since this is also useful for the device when a
normal connection is established, also program it
with the information in that case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This finalizes the move of the data path to the transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

priv->mac80211_registered and priv->hw needed to move to shared.
stop_queue API was added in order to allow the upper layer to stop
the SW queues for regulatory purposes.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This one is really transport related.

==== moves Stanislaw's code to BSD area ====
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This one is really transport related.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove a few dereferences of priv from the transport layer while
at it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since all the check_empty logic is now in the transport layer,
the upper layer doesn't need to know anything about tx queues.
The disable aggregation flow was the last to know what a tx queue
is, so move it too.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This logic is responsible to tell mac80211 when the HW queues are
empty and the BA session can be started / torn down.

Fix a bug on the way:
When the the Tx BA session is stopped and the HW queues aren't empty,
we stop the SW queue to drain the HW queue and then switch to the
legacy HW queue. This is the IWL_EMPTYING_HW_QUEUE_DELBA state.

While in this state, we never wake the SW queue, even when the HW
queue is almost empty, since we need to drain it completely. Look
at iwl_trans_pcie_reclaim regarding this.

Once the HW queue is really empty, we must wake the SW queue in order
to get traffic to the legacy queue.
This step was missing leading to an odd situation were the traffic
would just stall after we tore down a Tx BA session while the HW
queue was not empty.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queues and all the related logic suits to the transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This mapping is transport related.
This allows us to remove the notion of tx queue from the tx path in
the upper layer.
iwl_wake_any_queue moved to transport layer since it needs to access
these mappings.
The TX API is nicer now:

int (*tx)(struct iwl_trans *trans, struct sk_buff *skb,
		struct iwl_device_cmd *dev_cmd, u8 ctx, u8 sta_id);
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a near future, the upper layer won't be aware of the tx queues.
This allows to remove one place where the upper layer needed to
provide the tx queue index to the transport layer.
This also saves around 1.5MB.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the mapping tx_queue -> fifo is really transport related. The upper
layer should be involved in such things.

Note that upon agg_disable, the queue is always mapped to fifo 0, but
this doesn't matter since when the queue will be setup again for a
new BA session, it will be configured to the good fifo anyway.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the need for iwl_tx_info.
Each tx queue holds an array of skbs, the transport layer doesn't
need to know anything about the context in which a specific skb is
sent.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we remove the module, we free all the tx and rx resources.
Before doing that, we'd better stop the tx / rx activity. Calling
iwl_trans_stop_device in iwl_remove helps also to remove a few API
functions:
 * rx_free:		happens in iwl_trans_free
 * tx_free:		happens in iwl_trans_free
 * disable_sync_irq:	happens in iwl_trans_stop_device
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are still quite a few, but much less.
A few fields have been moved /copied to hw_params which sits in the
shared area:
 * priv->cfg->base_params->num_of_ampdu_queues
 * priv->cfg->base_params->shadow_reg_enable
 * priv->cfg->sku
 * priv->ucode_owner
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rate scaling and the transport need to access the data in
iwl_tid_data, hence the move.

Note that the only component in the upper layer that needs this data
is the rate scaling. Refactoring the rate scaling may help to move
iwl_tid_data from the shared area to the transport area.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

One more sku for 2000 series with different Subsystem ID
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move all the iwlXXX_abgn_cfg forward declaration to a separate file
so that iwl-pci.c doesn't need to include iwl-agn.h that includes
all iwl-dev.h
This allows to provide real encapsulation. Dereferencing iwl_priv
in the bus layer will now lead to a compilation error.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CC [M]  drivers/net/wireless/iwlwifi/iwl-pci.o
  drivers/net/wireless/iwlwifi/iwl-pci.c:506: warning: ‘iwl_pci_suspend’ defined but not used
  drivers/net/wireless/iwlwifi/iwl-pci.c:519: warning: ‘iwl_pci_resume’ defined but not used

These are only used if CONFIG_PM_SLEEP is enabled. CONFIG_PM depends
(CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME), so it can be set without
CONFIG_PM_SLEEP selected.
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Which means that iwl-io.c doesn't need to include iwl-dev.h any more.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

a few h files weren't self contained. Fix that.
Move iwl_dma_ptr to transport layer since it is not used by the upper layer
any more.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is relevant for PCIe only.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since iwl-fh.h contains transport related data, it shouldn't be included by the
upper layer.
Only the transport layer and iwl-agn-ucode.c includes it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of them weren't used at all, the others always had the same value since
the driver split.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Continue to the clean up of the priv dereferencing from the transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are transport layer related. Move also the corresponding debugfs handlers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since it is needed for host commands only, it is needed in transport layer only
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change a lot of functions to have them receive iwl_trans and not iwl_priv.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helper is used by the transport and the upper layer.
Kill __iwl_free_pages which was used in the transport only.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Logic move after all priv->status moved to struct iwl_shared
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BUILD_BUG_ON(ARRAY_SIZE(iwlagn_ipan_queue_to_tx_fifo) !=
						IWLAGN_FIRST_AMPDU_QUEUE);

This check can be buggy. IWLAGN_FIRST_AMPDU_QUEUE has to be greater than the
ARRAY_SIZE of iwlagn_ipan_queue_to_tx_fifo.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>