- 05 2月, 2010 2 次提交
-
-
由 Rafael J. Wysocki 提交于
Add missing try_to_freeze() to one of the pktgen_thread_worker() code paths so that it doesn't block suspend/hibernation. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=15006Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl> Reported-and-tested-by: NCiprian Dorin Craciun <ciprian.craciun@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This change corrects an issue that will cause false hangs when using either 82575 or 82580 in legacy interrupt mode. The issue is caused when there is a slow traffic flow and an "ethtool -r" is executed while using legacy or MSI interrupts. MSI-X is not affected by this issue due to the fact that we were already reconfiguring the vectors after reset. If possible it would be best to push this for net-2.6 since it is resolving a bug but if that is not possible then net-next-2.6 will be fine. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 2月, 2010 11 次提交
-
-
One ioctl has been forgotten when the BKL was push down into irnet_ppp ioctl function. Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
Add the missing unlock_kernel in one ioctl operation. Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Krishna Kumar 提交于
a developer had complained of getting lots of warnings: "eth16 selects TX queue 98, but real number of TX queues is 64" http://www.mail-archive.com/e1000-devel@lists.sourceforge.net/msg02200.html As there was no follow up on that bug, I am submitting this patch assuming that the other return points will not return invalid txq's, and also that this fixes the bug (not tested). Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Anton Blanchard 提交于
Commit e5a43549 (ixgbe: remove skb_dma_map/unmap calls from driver) looks to have introduced a bug in ixgbe_tx_map. If we get an error from a PCI DMA call, we loop backwards through count until it becomes -1 and return that. The caller of ixgbe_tx_map expects 0 on error, so return that instead. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Amit Kumar Salecha 提交于
o context resources can be in used, while resource cleanup is in progress, during fw recover. o Null pointer execption can occur in send_cmd_desc, if fw recovery module frees tx ring without rtnl lock. o Same applies to ethtool register dump. Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Amit Kumar Salecha 提交于
For NX2031, first try to scrub interrupt before requesting firmware reset. Return statement was missing after scrubbbing interrupt. Signed-off-by: NVernon Mauery <vernux@us.ibm.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gerrit Renker 提交于
This fixes commit (38ff3e6b) ("dccp_probe: Fix module load dependencies between dccp and dccp_probe", from 15 Jan). It fixes the construction of the first argument of try_then_request_module(), where only valid return codes from the first argument should be returned. What we do now is assign the result of register_jprobe() to ret, without the side effect of the comparison. Acked-by: NGerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gerrit Renker 提交于
This fixes a bug introduced in commit de4ef86c ("dccp: fix dccp rmmod when kernel configured to use slub", 17 Jan): the vsnprintf used sizeof(slab_name_fmt), which became truncated to 4 bytes, since slab_name_fmt is now a 4-byte pointer and no longer a 32-character array. This lead to error messages such as FATAL: Error inserting dccp: No buffer space available >> kernel: [ 1456.341501] kmem_cache_create: duplicate cache cci generated due to the truncation after the 3rd character. Fixed for the moment by introducing a symbolic constant. Tested to fix the bug. Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
The book keeping structure for transmit always had the flags value cleared so transmit DMA maps were never released correctly. Based on patch by Jarek Poplawski, problem observed by Michael Breuer. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexey Dobriyan 提交于
Netlink code does module autoload if protocol userspace is asking for is not ready. However, module can dissapear right after it was autoloaded. Example: modprobe/rmmod stress-testing and xfrm_user.ko providing NETLINK_XFRM. netlink_create() in such situation _will_ create userspace socket and _will_not_ pin module. Now if module was removed and we're going to call ->netlink_rcv into nothing: BUG: unable to handle kernel paging request at ffffffffa02f842a ^^^^^^^^^^^^^^^^ modules are loaded near these addresses here IP: [<ffffffffa02f842a>] 0xffffffffa02f842a PGD 161f067 PUD 1623063 PMD baa12067 PTE 0 Oops: 0010 [#1] PREEMPT SMP DEBUG_PAGEALLOC last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/uevent CPU 1 Pid: 11515, comm: ip Not tainted 2.6.33-rc5-netns-00594-gaaa5728-dirty #6 P5E/P5E RIP: 0010:[<ffffffffa02f842a>] [<ffffffffa02f842a>] 0xffffffffa02f842a RSP: 0018:ffff8800baa3db48 EFLAGS: 00010292 RAX: ffff8800baa3dfd8 RBX: ffff8800be353640 RCX: 0000000000000000 RDX: ffffffff81959380 RSI: ffff8800bab7f130 RDI: 0000000000000001 RBP: ffff8800baa3db58 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000011 R13: ffff8800be353640 R14: ffff8800bcdec240 R15: ffff8800bd488010 FS: 00007f93749656f0(0000) GS:ffff880002300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: ffffffffa02f842a CR3: 00000000ba82b000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process ip (pid: 11515, threadinfo ffff8800baa3c000, task ffff8800bab7eb30) Stack: ffffffff813637c0 ffff8800bd488000 ffff8800baa3dba8 ffffffff8136397d <0> 0000000000000000 ffffffff81344adc 7fffffffffffffff 0000000000000000 <0> ffff8800baa3ded8 ffff8800be353640 ffff8800bcdec240 0000000000000000 Call Trace: [<ffffffff813637c0>] ? netlink_unicast+0x100/0x2d0 [<ffffffff8136397d>] netlink_unicast+0x2bd/0x2d0 netlink_unicast_kernel: nlk->netlink_rcv(skb); [<ffffffff81344adc>] ? memcpy_fromiovec+0x6c/0x90 [<ffffffff81364263>] netlink_sendmsg+0x1d3/0x2d0 [<ffffffff8133975b>] sock_sendmsg+0xbb/0xf0 [<ffffffff8106cdeb>] ? __lock_acquire+0x27b/0xa60 [<ffffffff810a18c3>] ? might_fault+0x73/0xd0 [<ffffffff810a18c3>] ? might_fault+0x73/0xd0 [<ffffffff8106db22>] ? __lock_release+0x82/0x170 [<ffffffff810a190e>] ? might_fault+0xbe/0xd0 [<ffffffff810a18c3>] ? might_fault+0x73/0xd0 [<ffffffff81344c77>] ? verify_iovec+0x47/0xd0 [<ffffffff8133a509>] sys_sendmsg+0x1a9/0x360 [<ffffffff813c2be5>] ? _raw_spin_unlock_irqrestore+0x65/0x70 [<ffffffff8106aced>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff813c2bc2>] ? _raw_spin_unlock_irqrestore+0x42/0x70 [<ffffffff81197004>] ? __up_read+0x84/0xb0 [<ffffffff8106ac95>] ? trace_hardirqs_on_caller+0x145/0x190 [<ffffffff813c207f>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff8100262b>] system_call_fastpath+0x16/0x1b Code: Bad RIP value. RIP [<ffffffffa02f842a>] 0xffffffffa02f842a RSP <ffff8800baa3db48> CR2: ffffffffa02f842a If module was quickly removed after autoloading, return -E. Return -EPROTONOSUPPORT if module was quickly removed after autoloading. Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexey Dobriyan 提交于
1. After sock_register() returns, it's possible to create sockets, even if module still not initialized fully (blame generic module code for that!) 2. Consequently, pfkey_create() can be called with pfkey_net_id still not initialized which will BUG_ON in net_generic(): kernel BUG at include/net/netns/generic.h:43! 3. During netns shutdown, netns ops should be unregistered after key manager unregistered because key manager calls can be triggered from xfrm_user module: general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC pfkey_broadcast+0x111/0x210 [af_key] pfkey_send_notify+0x16a/0x300 [af_key] km_state_notify+0x41/0x70 xfrm_flush_sa+0x75/0x90 [xfrm_user] 4. Unregister netns ops after socket ops just in case and for symmetry. Reported by Luca Tettamanti. Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Tested-by: NLuca Tettamanti <kronos.it@gmail.com> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 2月, 2010 2 次提交
-
-
由 Evgeniy Polyakov 提交于
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote: > > There are at least two ways to fix it: using a big cannon and a small > > one. The former way is to disable notification registration, since it is > > not used by anyone at all. Second way is to check whether calling > > process is root and its destination group is -1 (kind of priveledged > > one) before command is dispatched to workqueue. > > Well if no one is using it, removing it makes the most sense, right? > > No objection from me, care to make up a patch either way for this? Getting it is not used, let's drop support for notifications about (un)registered events from connector. Another option was to check credentials on receiving, but we can always restore it without bugs if needed, but genetlink has a wider code base and none complained, that userspace can not get notification when some other clients were (un)registered. Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the code. Signed-off-by: NEvgeniy Polyakov <zbr@ioremap.net> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 2月, 2010 1 次提交
-
-
由 Sathya Perla 提交于
cev-isr reg offset for each function is better calculated using (any) eq-id alloted to that function instead of using pci-func number(which does not work in some configurations...) Signed-off-by: NSathya Perla <sathyap@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 2月, 2010 1 次提交
-
- 30 1月, 2010 5 次提交
-
-
由 Bastien Nocera 提交于
In commit 2da31939, support for Bluetooth hid_output_raw_report was added, but it pushes the data to the interrupt channel instead of the contol one. This patch makes hid_output_raw_report use the control channel instead. Using the interrupt channel was a mistake. Signed-off-by: NBastien Nocera <hadess@hadess.net> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Vikram Kandukuri 提交于
Signed-off-by: NVikram Kandukuri <vikram.kandukuri@atheros.com> Signed-off-by: NAlicke Xu <sxu@atheros.com> Reviewed-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Mike Frysinger 提交于
Commit ac019360 changed the irq handler logic to BUG_ON rather than returning IRQ_NONE when the incoming argument is invalid. While this works in most cases, it doesn't work when the IRQ is shared with other devices (or when DEBUG_SHIRQ is enabled). So revert the previous change and replace the warning message with a comment explaining that we want this behavior. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Andrei Emeltchenko 提交于
Move skb_clone after error confition check so it is not going potentially out of the scope. Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com> Acked-by: NGustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
由 Andrei Emeltchenko 提交于
Trivial fix for double free of SKB pointer with kfree_skb to make code simplier and cleaner. Remove unused variable err. Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com> Acked-by: NGustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
-
- 29 1月, 2010 2 次提交
-
-
由 Ben Hutchings 提交于
Commit 37e8273c ("usbnet: Set link down initially for drivers that update link state") changed the initial link state in cdc_ether and other drivers based on the understanding that the devices they support generate link change interrupts. However, this is optional in the CDC Ethernet protocol, and two users have reported in <http://bugzilla.kernel.org/show_bug.cgi?id=14791> that the link state for their devices remains down. Therefore, revert the change in cdc_ether. Signed-off-by: NBen Hutchings <ben@decadent.org.uk> Tested-by: NAvi Rozen <avi.rozen@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Noticed by Ben Hutchings. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 1月, 2010 7 次提交
-
-
由 stephen hemminger 提交于
The convention for API functions in kernel is to return errno value; bond_open would return -1 if alb setup failed. The only reason that could happen is if kmalloc() failed. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John Fastabend 提交于
Call ixgbe_copy_dcb_cfg() earlier in the ixgbe_dcbnl_set_all() so that we can learn if this is going to fail as early as possible. Previously, ixgbe_down or ixgbe_close were being called before this check and the IXGBE_RESETTING bit was being set and cleared. Worse if this failed the corresponding ixgbe_up/ndo_open would not called. Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Acked-by: NPJ Waskiewicz <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John Fastabend 提交于
Set the correct bit BIT_PG_TX when tx PG settings are set. Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Acked-by: NPJ Waskiewicz <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This change fixes an issue in igbvf with mapped_as_page being left set after a page is unmapped which results in buffers which are mapped via map single being unmapped as page. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Choi, David 提交于
Hello David Miller, I fix a bug in ks8851_mll driver, which has existed since 2.6.32-rc6. >From : David J. Choi <david.choi@micrel.com> Fix a bug that the data pointers in the interrupt handler are set wrong, which is related with the 5th parameter of request_irq(). Signed-off-by : David J. Choi <david.choi@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
Bug fix in be2net for newer generation of BladeEngine ASIC. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 1月, 2010 3 次提交
-
-
由 Ben Hutchings 提交于
netdev_open() will return without cleaning up net device or hardware state if firmware loading fails. This results in a BUG() on a second attempt to bring the interface up, reported in <http://bugzilla.kernel.org/show_bug.cgi?id=15091>, and probably has even worse effects if the driver is removed afterwards. Call netdev_close() to clean up on failure. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15091Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Reported-by: NMichael Moffatt <michael@moffatt.org.nz> Tested-by: NMichael Moffatt <michael@moffatt.org.nz> Cc: "David S. Miller" <davem@davemloft.net> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Zhu Yi 提交于
I got below kernel oops when I try to bring down the network interface if ftrace is enabled. The root cause is drv_ampdu_action() is passed with a NULL ssn pointer in the BA session tear down case. We need to check and avoid dereferencing it in trace entry assignment. BUG: unable to handle kernel NULL pointer dereference Modules linked in: at (null) IP: [<f98fe02a>] ftrace_raw_event_drv_ampdu_action+0x10a/0x160 [mac80211] *pde = 00000000 Oops: 0000 [#1] SMP DEBUG_PAGEALLOC [...] Call Trace: [<f98fdf20>] ? ftrace_raw_event_drv_ampdu_action+0x0/0x160 [mac80211] [<f98dac4c>] ? __ieee80211_stop_rx_ba_session+0xfc/0x220 [mac80211] [<f98d97fb>] ? ieee80211_sta_tear_down_BA_sessions+0x3b/0x50 [mac80211] [<f98dc6f6>] ? ieee80211_set_disassoc+0xe6/0x230 [mac80211] [<f98dc6ac>] ? ieee80211_set_disassoc+0x9c/0x230 [mac80211] [<f98dcbb8>] ? ieee80211_mgd_deauth+0x158/0x170 [mac80211] [<f98e4bdb>] ? ieee80211_deauth+0x1b/0x20 [mac80211] [<f8987f49>] ? __cfg80211_mlme_deauth+0xe9/0x120 [cfg80211] [<f898b870>] ? __cfg80211_disconnect+0x170/0x1d0 [cfg80211] Cc: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: NZhu Yi <yi.zhu@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Patrick McHardy 提交于
The protocol number is not initialized, so userspace can't interpret the layer 4 data properly. Signed-off-by: NPatrick McHardy <kaber@trash.net>
-
- 26 1月, 2010 6 次提交
-
-
由 Shan Wei 提交于
The commit 0b5ccb2e(title:ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery) has broken the saddr&&daddr member of nf_ct_frag6_queue when creating new queue. And then hash value generated by nf_hashfn() was not equal with that generated by fq_find(). So, a new received fragment can't be inserted to right queue. The patch fixes the bug with adding member of user to nf_ct_frag6_queue structure. Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com> Acked-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
I have seen RX stalls on a machine that experienced a suspected OOM. After the stall, the RX buffer is empty on the guest side and there are exactly 16 entries available on the host side. As the number of entries is less than that required by a maximal skb, the host cannot proceed. The guest did not have a refill job scheduled. My diagnosis is that an OOM had occured, with the delayed refill job scheduled. The job was able to allocate at least one skb, but not enough to overcome the minimum required by the host to proceed. As the refill job would only reschedule itself if it failed completely to allocate any skbs, this would lead to an RX stall. The following patch removes this stall possibility by always rescheduling the refill job until the ring is totally refilled. Testing has shown that the RX stall no longer occurs whereas previously it would occur within a day. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Acked-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ben Hutchings 提交于
The low-level MCDI code always uses 32-bit MMIO operations, and callers must pad input and output buffers to multiples of 4 bytes. The MCDI NVRAM functions are not doing this. Also, their buffers are declared as variable-length arrays with no explicit maximum length. Switch to a fixed buffer size based on the chunk size used by the MTD driver (which is a multiple of 4). Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guido Barzini 提交于
Due to a hardware bug in the SFC9000 family, the firmware must transfer raw GMAC statistics to host memory before aggregating them into the cooked (speed-independent) MAC statistics. Extend the stats buffer to support this. The length of the buffer is explicit in the MAC_STATS command, so this change is backward-compatible on both sides. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
By rounding up the buffer size to power of 2, several expensive modulus operations can be avoided. This patch also solves a bug where the gap need when ring gets full was not being accounted for. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Breno Leitao 提交于
Currently qlge tries to release regions even if they were not allocated. This causes messages like the following in the kernel log Trying to free nonexistent resource <00000000006af400-00000000006af4ff> Trying to free nonexistent resource <00003c04ff9f4000-00003c04ff9f7fff> Trying to free nonexistent resource <00003c04ffc00000-00003c04ffcfffff> This patch fixes the goto logic in order to not release the resources if they were not allocated. Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-