Updated the device trees to have the PCI nodes be at the same level as
the SOC node.  This is to make it so that the SOC nodes children address
space is just on chip registers and not other bus memory as well.

Also, for PCIe nodes added a P2P bridge to handle the virtual P2P bridge
that exists in the PHB.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Removed the following cruft from .dts files:
* 32-bit in cpu node -- doesn't exist in any spec and not used by kernel
* removed built-in (chrp legacy)
* Removed #interrupt-cells in places they don't need to be set
* Fixed ranges on lite5200*
* Removed clock-frequency from i8259 pic node, not sure where this came from
* Removed big-endian from i8259 pic nodes, this was just bogus
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Added basic board port for MPC8572 DS reference platform that is
similiar to the MPC8544/33 DS reference platform in uniprocessor mode.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. Fix RTC type - it is a rs5c372a, not rs5c372b
2. Configure both UART interrupts edge-triggered
3. Add a license header to ls_uart.c
4. Check for running on linkstation in a late_initcall() function. Needed
   for multiplatform builds, even though linkstation doesn't support them
   yet
5. Remove unneeded #include from linkstation.c
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This replaces the binding for flash chips in booting-without-of.txt
with an clarified and improved version.  It also makes
drivers/mtd/maps/physmap_of.c recognize this new binding.  Finally it
revises the Ebony device tree source to use the new binding as an
example.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NSegher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some firmwares (such as PlanetCore) only provide a base MAC address, and
expect the kernel to set certain bits to generate the addresses for the
other ports.  As such, MAC addresses are generated that may not correspond
to actual hardware.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This will be used by the PlanetCore firmware support to construct
a linux,stdout-path from the serial node that it finds.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This will be needed by PlanetCore firmware support.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

1. ft_create_node was returning the internal pointer rather than a phandle.
2. ft_find_device_rel was treating a "top" phandle of NULL as an error,
rather than as the root of the tree.  The old, absolute ft_find_device
is removed, and the relative version is renamed to ft_find_device().
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently the bootwrapper has implementations of strchr() and
strncmp(), but they're inlines in flatdevtree_env.h, rather than in
string.S with all the rest of the string functions.  This moves
them to string.S.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add zImage wrapper for walnut board
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

Device tree source file for the PPC405 Walnut evaluation board.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

The patch below removes the dtc incantation instructions from the
in-kernel DTS files.  It's not needed, and is prone to being
out-of-date most of the time.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

Bootwrapper code for AMCC PPC440EPx Sequoia.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

AMCC PPC440EPx Sequoia device tree.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This allows booting on legacy, non-device-tree aware versions of U-boot.

It also fixes up the hardware to match the PCI and chipselect information
in the device tree, as u-boot is inconsistent in setting these up
correctly (or at all).
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This allows booting on legacy, non-device-tree aware versions of U-boot.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Most of these were previously used by numerous C files and
redeclared in each one.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This serial port is used on all 8xx, many 82xx, and some 85xx chips.

The driver requires that the port has already been set up by the firmware
and/or platform code.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Declarations in various users are removed.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

1. Search the entire compatible list for serial devices.

The serial code previously did a simple strcmp on the compatible
node; this fails when the match string is not the first compatible
listed.  Use dt_is_compatible() instead.

2. Don't call serial_edit_cmdline if getc isn't defined.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

U-boots more recent than when ppcboot.h was forked allow the board config
file to enable additional ethernet ports explicitly, rather than
using a hardcoded list of targets.  This allows bootwrapper platform
files to do the same.

Fortunately, nothing after the ethernet addresses is of interest to
cuboot platforms, so the inevitable mismatches won't be too catastrophic.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Also, include types.h from io.h, so callers don't have to.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This can be used rather than doing a simple strcmp, which will fail to
handle multiple compatible entries.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

1. The check whether ranges fits in the buffer was using elements rather
than bytes.
2. Empty ranges were not properly treated as transparent, and missing
ranges were treated as transparent.
3. The loop terminated when translating from the root rather than to.  Once
bug #2 was fixed, it failed due to a missing ranges in the root node.
4. In decoding the ranges property, the #size-cells used was that of
the parent, not the child.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This lets udelay() work properly on platforms which use dt_fixup_cpu_clocks.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

All cuImage types are ignored, as well as preprocessed .lds files,
and the forthcoming zImage.bin files and embedded planet board images.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add a bootwrapper for the AMCC 440EP Bamboo Eval board.  This also adds a
common fixup_clock function for all 440EP(x) chips.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

AMCC Bamboo board DTS
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Make the fixup_memsize function common for all of 4xx as several chips share
the same SDRAM controller.  Also add functions to reset 40x chips and quiesce
the ethernet.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Rename the 44x.c wrapper file to 4xx.c.  This will allow us to add common
functions in a single file that can be shared across all of 4xx.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function.  Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:

PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15

Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.

Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.

Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch contains a handful of small fixes to allow the Ebony's
flash to be exposed as MTD devices via the physmap_of driver.
Specifically it:
	- Makes a small addition to the device tree and zImage wrapper
to record the correct address for the flash in the device tree based
on the board switches as reported via an FPGA register.
	- Prohibits building the old hard-coded "Ebony" flash map on
arch/powerpc kernels, in favour of using physmap_of's device tree
based approach.
	- Enables MTD and physmap_of in the Ebony defconfig.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

AFAICT, nobody is using ft_ordered(), and it causes a build warning
to be generated.  This patch cleans that up by removing the function
and the commented-out code that calls it.
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the RTC on linkstation ppc machines again, and updates the
device tree: add rtc nodes on i2c, remove bogus 0-size cache-line
declarations, rename interrupt-controller nodes, remove erroneous
interrupt-parent line, accidentally introduced by a recent patch.
Signed-off-by: NG. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add global-utilities node with has-rstcr on MPC8544 DS and MPC8568 MDS
boards so they are able to reset properly.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix mpc7448hpc2 tsi108 device_type bug.
Wrong device type will break the board startup.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC8544 dts needed to set the new phy-connection-type to rgmii-id
for the Vitesse PHY on the board to work properly.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>