Although on HSW/BDW there is only a single display global power well,
it's programmed the same way as other GEN9+ power wells. This also
means we can get at the HSW/BDW request and status flags the same way
it's done on GEN9+ by assigning the corresponding HSW/BDW power well ID.
This ID was assigned in a recent patch, so we can now switch to using
the same macros everywhere on HSW+.

Updating the HSW power well control register with RMW is not strictly
necessary, but this will allow us to use the same code for GEN9+.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-13-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can reduce the code indentation by splitting the set helper to
separate enable/disable helpers. This also allows us to unify the
HSW/BDW and GEN9+ power well ops in follow-up patches, which introduces
some differences between the enable and disable helpers.

While at it also remove the redundant enable/disable debug messages,
the same info is printed already elsewhere.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-12-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similarly to the GEN9 power well toggling, saving an occasional extra
MMIO write is not worth the code complexity, let's simplify things.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-11-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Atm we enable/disable a power well only if it wasn't already
enabled/disabled respectively. The only reason for this I can think of
is to save the extra MMIO writes. Since the HW state matches the power
well's usage counter most of the time the overhead due to these MMIOs is
insignificant. Let's simplify the code by making the writes
unconditional.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-10-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We check already for power wells that are unexpectedly on (or forced on)
during power well disabling. Those checks also account for other
power well requesters like KVMR or DEBUG. As such this check is
redundant, let's remove it to simplify things.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-9-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Follow-up patches will add new fields to the i915_power_well struct that
are specific to the hsw_power_well_ops helpers. Prepare for this by
changing the generic 'data' field to a union of platform specific
structs.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-8-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Check that all the power well IDs are unique on the given platform.

v2:
- Fix using BIT_ULL() instead of BIT() for 64 bit mask.
v3:
- Move the check to a separate function. (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-4-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add an ID for the HSW/BDW global display power well for consistency. The
ID is selected so that it can be used to get at the HW request and
status flags with the corresponding GEN9+ macros. Unifying the HSW/BDW
and GEN9+ versions of these macros and the power well ops using them
will be done in follow-up patches.

v2:
- Rebased on v2 of patch 2.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-3-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make the I830 power well ID assignment explicit for consistency.

v2:
- s/GEN2/I830/ in the comment, since other GEN2s don't have the power
  well. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-2-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Power well IDs are used for lookup so they must be unique. To ensure
this assign the always-on power well ID everywhere where it's missing.
This didn't cause a problem so far, since we didn't need to look up
power wells that happened to share their IDs.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-4-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Atm, the power well IDs are defined in separate platform specific enums,
which isn't ideal for the following reasons:
- the IDs are used by helpers like lookup_power_well() in a platform
  independent way
- the always-on power well is used by multiple platforms and so needs
  now separate IDs, although these IDs refer to the same thing

To make things more consistent use a single enum instead of the two
separate ones, listing the IDs per platform (or set of very similar
platforms like all GEN9/10). Replace the separate always-on power
well IDs with a single ID.

While at it also add a note clarifying the distinction between regular
power wells that follow a common programming pattern and custom ones
that are programmed in some other way. The IDs for regular power wells
need to stay fixed, since they also define the request and state HW flag
positions in their corresponding power well control register(s).

v2:
- Add comment about id to req,status bit mapping to the enum. (Rodrigo)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-1-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The power well IDs are used for lookup, so they must be unique on a
given platform; ensure this on CHV. This didn't cause an actual problem
since we didn't need to look up power wells which happened to share an
ID.

Mark this new power well as custom, since its programming pattern
doesn't follow that of the rest of VLV/CHV power wells.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-2-git-send-email-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The crtc state starts out being bzero'd, so no need to clear
scaler_users. Also intel_crtc_init_scalers() knows already which
platforms have scalers, so no need for the platform check here.
Similarly intel_crtc_init_scalers() will init scaler_id as required,
so no need to do it here separately.

Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719225057.20131-2-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The scaler allocation code depends on a non-zero default value for the
crtc scaler_id, so make sure we initialize the scaler state accordingly
even if the crtc is off. This fixes at least an initial YUV420 modeset
(added in a follow-up patchset by Shashank) when booting with the screen
off: after the initial HW readout and modeset which enables the scaler a
subsequent modeset will disable the scaler which isn't properly
allocated. This results in a funky HW state where the pipe scaler HW
registers can't be modified and the normally black screen is grey and
shifted to the right or jitters.

The problem was revealed by Shashank's YUV420 patchset and first
reported by Ville.

v2:
- In the stable tag also include versions which need backporting (Jani)

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: <stable@vger.kernel.org> # 4.2.x
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Fixes: a1b2278e ("drm/i915: skylake panel fitting using shared scalers")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170720112820.26816-1-imre.deak@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If all goes well, resetting one engine should not affect the operation of
any others. So to test this, we setup a continuous stream of requests
onto to each of the "innocent" engines whilst constantly resetting our
target engine.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-16-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Triggering a GPU reset for one engine affects another, notably
corrupting the context status buffer (CSB) effectively losing track of
inflight requests.

Adding a few printks:
diff --git a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c
index ad41836fa5e5..a969456bc0fa 100644
--- a/drivers/gpu/drm/i915/i915_drv.c
+++ b/drivers/gpu/drm/i915/i915_drv.c
@@ -1953,6 +1953,7 @@ int i915_reset_engine(struct intel_engine_cs *engine)
                goto out;
        }

+       pr_err("Resetting %s\n", engine->name);
        ret = intel_gpu_reset(engine->i915, intel_engine_flag(engine));
        if (ret) {
                /* If we fail here, we expect to fallback to a global reset */
diff --git a/drivers/gpu/drm/i915/intel_lrc.c b/drivers/gpu/drm/i915/intel_lrc.c
index 716e5c9ea222..a72bc35d0870 100644
--- a/drivers/gpu/drm/i915/intel_lrc.c
+++ b/drivers/gpu/drm/i915/intel_lrc.c
@@ -355,6 +355,7 @@ static void execlists_submit_ports(struct intel_engine_cs *engine)
                                execlists_context_status_change(rq, INTEL_CONTEXT_SCHEDULE_IN);
                        port_set(&port[n], port_pack(rq, count));
                        desc = execlists_update_context(rq);
+                       pr_err("%s: in (rq=%x) ctx=%d\n", engine->name, rq->global_seqno, upper_32_bits(desc));
                        GEM_DEBUG_EXEC(port[n].context_id = upper_32_bits(desc));
                } else {
                        GEM_BUG_ON(!n);
@@ -594,9 +595,23 @@ static void intel_lrc_irq_handler(unsigned long data)
                        if (!(status & GEN8_CTX_STATUS_COMPLETED_MASK))
                                continue;

+                       pr_err("%s: out CSB (%x head=%d, tail=%d), ctx=%d, rq=%d\n",
+                                       engine->name,
+                                       readl(csb_mmio),
+                                       head, tail,
+                                       readl(buf+2*head+1),
+                                       port->context_id);
+
                        /* Check the context/desc id for this event matches */
-                       GEM_DEBUG_BUG_ON(readl(buf + 2 * head + 1) !=
-                                        port->context_id);
+                       if (readl(buf + 2 * head + 1) != port->context_id) {
+                               pr_err("%s: BUG CSB (%x head=%d, tail=%d), ctx=%d, rq=%d\n",
+                                               engine->name,
+                                               readl(csb_mmio),
+                                               head, tail,
+                                               readl(buf+2*head+1),
+                                               port->context_id);
+                               BUG();
+                       }

                        rq = port_unpack(port, &count);
                        GEM_BUG_ON(count == 0);

Results in:

[ 6423.006602] Resetting rcs0
[ 6423.009080] rcs0: in (rq=fffffe70) ctx=1
[ 6423.009216] rcs0: in (rq=fffffe6f) ctx=3
[ 6423.009542] rcs0: out CSB (2 head=1, tail=2), ctx=3, rq=3
[ 6423.009619] Resetting bcs0
[ 6423.009980] rcs0: BUG CSB (0 head=1, tail=2), ctx=0, rq=3

Note that this bug may be affect all machines and not just Broxton,
Broxton is just the first machine on which I have confirmed this bug.

Fixes: 142bc7d9 ("drm/i915: Modify error handler for per engine hang recovery")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Acked-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-13-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Although a banned context will be told to -EIO off if they try to submit
more requests, we have a discrepancy between whole device resets and
per-engine resets where we report the GPU reset but not the engine
resets. This leaves a bit of mystery as to why the context was banned,
and also reduces awareness overall of when a GPU (engine) reset occurs
with its possible side-effects.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-13-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since we make call i915_gem_context_mark_guilty() concurrently when
resetting different engines in parallel, we need to make sure that our
updates are safe for the unlocked access.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-12-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When the GPU is reset, we want to discard all pending notifications as
either we have manually completed them, or they are no longer
applicable. Make sure we do reset the engine->irq_posted prior to
re-enabling the engine (e.g. the interrupt tasklets) in
i915_gem_reset_finish_engine().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-11-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should only ever do nop_submit_request when the machine is wedged, so
assert it is so.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-10-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After setting the WEDGED bit, make sure that we do wake up waiters as
they may not be waiting for a request completion yet, just for its
execution.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-9-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_engine_init_globa_seqno() may be called from an uncontrolled
set-wedged path where we have given up waiting for broken hw and declare
it defunct. Along that path, any sanity checks that the hw is idle
before we adjust its state will expectedly fail, so we simply cannot.
Instead of asserting inside init_global_seqno, we move them to the
normal caller reset_all_global_seqno() as it handles runtime seqno
wraparound.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-8-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we wedge the device, we clear out the in-flight requests and
advance the breadcrumb to indicate they are complete. However, the
breadcrumb advance includes an assert that the engine is idle, so that
advancement needs to be the last step to ensure we pass our own sanity
checks.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-7-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Including a check against the execlist queue before calling the engine
idle and passing hangcheck.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-6-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Before we declare an engine as idle, check if there are any pending
execlist context-switches and if the ring itself reports as idle.
Otherwise, we may be left in a situation where we miss a crucial
execlist event (or something more sinister) yet the requests complete.
Since the seqno write happens, we believe the engine to be truly idle.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-5-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When doing a GPU reset, the CSB register will be trashed and we will
lose any context-switch notifications that happened since the tasklet
was disabled. If we find that all requests on this engine were
completed, we want to make sure that the ELSP tracker is similarly empty
so that we do not feed back in the completed requests upon recovering
from the reset.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-4-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We rely on disabling the execlists (by stopping the tasklet) to prevent
new requests from submitting to the engine ELSP before we are ready.
However, we re-enable the engine before we call init_hw which gives
userspace the opportunity to subit a new request which is then
overwritten by init_hw -- but not before the HW may have started
executing. The subsequent out-of-order CSB is detected by our sanity
checks in intel_lrc_irq_handler().

Fixes: a1ef70e1 ("drm/i915: Add support for per engine reset recovery")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-3-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We try to fixup the context image after the reset to ensure that there
are no more pending writes from the hw that may conflict and to fixup
any that were in flight.

Fixes: a1ef70e1 ("drm/i915: Add support for per engine reset recovery")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-2-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As part of the knowing whether there is outstanding data in the CSB,
also check whether there is an outstanding IRQ notification.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-1-chris@chris-wilson.co.ukSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We cannot reference priv->fbdev outside of the #ifdef:

drivers/net/virtio_net.c:1881:12: error: 'virtnet_restore_up' defined but not used [-Werror=unused-function]
 static int virtnet_restore_up(struct virtio_device *vdev)
drivers/net/virtio_net.c:1859:13: error: 'virtnet_freeze_down' defined but not used [-Werror=unused-function]
 static void virtnet_freeze_down(struct virtio_device *vdev)

As the #ifdef is a bit annoying here, this removes it entirely
and uses an IS_ENABLED() check in it place where needed.

Fixes: b4dd9f1ffaba ("drm/hisilicon: Remove custom FB helper deferred setup")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[danvet: One step further, also remove the IS_ENABLED checks, core
no-ops out the fb helper functions that the cma helpers use. Discussed
with Arnd on dri-devel.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725180555.3699056-1-arnd@arndb.deSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The current drm_atomic_helper_commit_tail helper works only if the CRTC is
accessible, and documents an alternative implementation that is supposed to
be used if that happens.

That implementation is then duplicated by some drivers. Instead of
documenting it, let's implement an helper that all the relevant users can
use directly.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a8f92dc70048bab746e94dadd1c23200626aff60.1500555652.git-series.maxime.ripard@free-electrons.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Explain better when the drm_modeset_acquire_ctx parameter can
be skipped for drm_modeset_lock() call.
Signed-off-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170720160748.12856-1-Liviu.Dudau@arm.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The FB helper core now supports deferred setup, so the driver's custom
implementation can be removed.

v2: Dont' resurrect drm_vblank_cleanup.

Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Thierry Reding <treding@nvidia.com> (v1)
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170706130023.28417-5-daniel.vetter@ffwll.chSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The FB helper core now supports deferred setup, so the driver's custom
implementation can be removed.

v2: Drop NULL check, drm_fb_helper_hotplug_event handles that already.

Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com> (v1)
Reviewed-by: NInki Dae <inki.dae@samsung.com>
Tested-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170706130023.28417-4-daniel.vetter@ffwll.chSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

FB helper code falls back to a 1024x768 mode if no outputs are connected
or don't report back any modes upon initialization. This can be annoying
because outputs that are added to FB helper later on can't be used with
FB helper if they don't support a matching mode.

The fallback is in place because VGA connectors can happen to report an
unknown connection status even when they are in fact connected.

Some drivers have custom solutions in place to defer FB helper setup
until at least one output is connected. But the logic behind these
solutions is always the same and there is nothing driver-specific about
it, so a better alterative is to fix the FB helper core and add support
for all drivers automatically.

This patch adds support for deferred FB helper setup. It checks all the
connectors for their connection status, and if all of them report to be
disconnected marks the FB helper as needing deferred setup. Whet setup
is deferred, the FB helper core will automatically retry setup after a
hotplug event, and it will keep trying until it succeeds.

v2: Rebase onto my entirely reworked fbdev helper locking. One big
difference is that this version again drops&reacquires the fbdev lock
(which is now fb_helper->lock, but before this patch series it was
mode_config->mutex), because register_framebuffer must be able to
recurse back into fbdev helper code for the initial screen setup.

v3: __drm_fb_helper_initial_config must hold fb_helper->lock upon
return, I've fumbled that in the deferred setup case (Liviu).

v4: I was blind, redo this all. __drm_fb_helper_initial_config
shouldn't need to reacquire fb_helper->lock, that just confuses
callers. I myself got confused by kernel_fb_helper_lock and somehow
thought it's the same as fb_helper->lock. Tsk.

Also simplify the logic a bit (we don't need two functions to probe
connectors), we can stick much closer to the existing code. And update
some comments I've spotted that are outdated.

v5: Don't pass -EAGAIN to drivers, it's just an internal error code
(Liviu).

v6: Add _and_unlock suffix to clarify locking (Maarten)

Cc: Liviu Dudau <liviu@dudau.co.uk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com> (v1)
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@intel.com>
Reviewed-by: NLiviu Dudau <liviu@dudau.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170706130023.28417-3-daniel.vetter@ffwll.chSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Partially-Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul changed subject prefix and fixed conflict in stm/ltdc.c]
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

make htmldocs helps with catching these.

Cc: Dave Airlie <airlied@gmail.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170718074113.5554-1-daniel.vetter@ffwll.chSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-13-maarten.lankhorst@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drm_atomic_helper_swap_state() will be changed to interruptible waiting
in the next few commits, so all drivers have to be changed to handling
failure.

VC4 has its own nonblocking modeset tracking through the vc4->async_modeset
semaphore, so it doesn't need to stall in swap_state. Pass stall = false
and BUG_ON when it returns an error. This should never happen for !stall.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-11-maarten.lankhorst@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drm_atomic_helper_swap_state() will be changed to interruptible waiting
in the next few commits, so all drivers have to be changed to handling
failure.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-10-maarten.lankhorst@linux.intel.comReviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>