This device presents a total of 5 interfaces with ff/ff/ff
class/subclass/protocol. The last one of these is verified
to be a QMI/wwan combined interface which should be handled
by the qmi_wwan driver, so we blacklist it here.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0d905fd5 "USB: option: convert Huawei K3765, K4505, K4605
reservered interface to blacklist" accidentally ANDed two
blacklist tests by leaving out a return.  This was not noticed
because the two consecutive bracketless if statements made it
syntactically correct.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: <stable@vger.kernel.org> # 3.2.y, 3.3.y
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NMichał Wróbel <michal.wrobel@flytronic.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add PID 0x6015, corresponding to the new series of FT-X chips
(FT220XD, FT201X, FT220X, FT221X, FT230X, FT231X, FT240X).  They all
appear as serial devices, and seem indistinguishable except for the
default product string stored in their EEPROM.  The baudrate
generation matches FT232RL devices.

Tested with a FT201X and FT230X at various baudrates (100 - 3000000).

Sample dmesg:
    ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
    usb 2-1: new full-speed USB device number 6 using ohci_hcd
    usb 2-1: New USB device found, idVendor=0403, idProduct=6015
    usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    usb 2-1: Product: FT230X USB Half UART
    usb 2-1: Manufacturer: FTDI
    usb 2-1: SerialNumber: DC001WI6
    ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected
    drivers/usb/serial/ftdi_sio.c: ftdi_sio_port_probe
    drivers/usb/serial/ftdi_sio.c: ftdi_determine_type: bcdDevice = 0x1000, bNumInterfaces = 1
    usb 2-1: Detected FT-X
    usb 2-1: Number of endpoints 2
    usb 2-1: Endpoint 1 MaxPacketSize 64
    usb 2-1: Endpoint 2 MaxPacketSize 64
    usb 2-1: Setting MaxPacketSize 64
    drivers/usb/serial/ftdi_sio.c: read_latency_timer
    drivers/usb/serial/ftdi_sio.c: write_latency_timer: setting latency timer = 1
    drivers/usb/serial/ftdi_sio.c: create_sysfs_attrs
    drivers/usb/serial/ftdi_sio.c: sysfs attributes for FT-X
    usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0
Signed-off-by: NJim Paris <jim@jtan.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A MCS7820 device supports two serial ports and a MCS7840 device supports
four serial ports. Both devices use the same driver, but the attach function
in driver was unable to correctly handle the port numbers for MCS7820
device. This problem has been fixed in this patch and this fix has been
verified on x86 Linux kernel 3.2.9 with both MCS7820 and MCS7840 devices.
Signed-off-by: NDonald Lee <donald@asix.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NMichał Wróbel <michal.wrobel@flytronic.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This properly ties the driver into the dynamic debug system and provides
the needed device identification when the messages are printed out.

It also removes a ton of checkpatch warnings as well, which is always a
nice validation that it's the correct thing to do.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should use kzalloc() instead of kmalloc() and memset(), and remove an
unneeded void * cast as well.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

They aren't needed, make the checkpatch tool unhappy, and in some
places, aren't even correct.  So just remove them, they get in the way
and are messy.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

By rearranging the functions a bit, we can remove all function
prototypes.

Note, this also deleted the _close function, as it wasn't needed, it was
doing the same thing the cleanup function did, so just call that
instead.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes up all of the coding style errors, and removes the initial,
unneeded comments on how to load the module and the old changelog which
are no longer needed.

There are still a number of coding style warnings left, I'll get to them
later.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A driver doesn't need a .h file just for simple things like vendor ids
and a private structure.  So move it into the .c file instead, saving
some overall lines.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that we aren't doing anything special in the init function, move to
use the easier module_usb_serial_driver() call instead, saving a lot of
lines of unnecessary code.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All new usb serial drivers should be using the dynamic id function, not
having module parameters for this type of thing.  So remove them before
anyone gets used to them being there.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the metro-usb driver to the build system properly.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The usb serial core has changed how the driver is to be registered and
unregistered recently.  Make these changes to the driver so that it will
properly build and work.

Cc: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver is for the Metrologic barcode scanner.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Microchip VID (0x04d8) was mislabeled as Hornby VID according to USB-IDs.

A Full Speed USB Demo Board PID (0x000a) was mislabeled as
Hornby Elite (an Digital Command Controller Console for model railways).

Most likely the Hornby based their design on
PIC18F87J50 Full Speed USB Demo Board.
Signed-off-by: NBruno Thomsen <bruno.thomsen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.

pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch updates the cp210x driver to support CP210x multiple
interface devices devices from Silicon Labs. The existing driver
always sends control requests to interface 0, which is hardcoded in
the usb_control_msg function calls. This only allows for single
interface devices to be used, and causes a bug when using ports on an
interface other than 0 in the multiple interface devices.

Here are the changes included in this patch:
- Updated the device list to contain the Silicon Labs factory default
  VID/PID for multiple interface CP210x devices
- Created a cp210x_port_private struct created for each port on
  startup, this struct holds the interface number
- Added a cp210x_release function to clean up the cp210x_port_private
  memory created on startup
- Modified usb_get_config and usb_set_config to get a pointer to the
  cp210x_port_private struct, and use the interface number there in the
  usb_control_message wIndex param
Signed-off-by: NPreston Fick <preston.fick@silabs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

BeagleBone changed to the default FTDI 0403:6010 id in rev A5 to make life
easier for Windows users, so we need a similar workaround as the Calao
board to support it.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding PID for Telit CC864-SINGLE, CC864-DUAL and DE910-DUAL
modems
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is the first cut at a driver for the Fintek F81232 USB to serial
single port converter.  This provides the initial framework for the
device, and some data can move through it, but no line settings are
handled, so it's not that useful yet.  It does give people a starting
place to work from.

Thank to Fintek for providing samples and specifications, without which,
this driver would have never been able to be written.

Cc: Amanda Ying <Amanda_Ying@fintek.com.tw>
Cc: Tom Tsai <Tom_Tsai@fintek.com.tw>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the zio.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the whiteheat.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Support Department <support@connecttech.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the vivopay-serial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the usb_debug.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the symbolserial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the ssu100.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the spcp8x5.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the sierra.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the siemens_mpi.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the qcserial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Steven Hardy <shardy@redhat.com>
CC: Thomas Tuttle <ttuttle@chromium.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the qcaux.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Dan Williams <dcbw@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the oti6858.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the option.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the opticon.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Julia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the omninet.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the navman.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This converts the moto_modem.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Elizabeth Jennifer Myers <elizabeth@sporksirc.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>