"unsigned" translates to "unsigned int", but this value holds an
address. We always want to use unsigned long for addresses since
it will change size to fit the machine.

This just convert the one address holder to unsigned long.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This modifies SMD to use either the package v3 or package v4,
but not both. The current code tries to allocate as v4 on all
system which can produce a scary looking error message on boot up,

smem_find(16, 40): wrong size 16424
smd_alloc_channel() cid=02 size=08192 'SMD_RPCCALL'

With this error the code then falls back on the package v3 allocation
method. This method is inefficient because it causes a slow down
on some systems even when the allocation method can be determined
at compile time. It also causes a kernel size increase that effects
all system and is not needed.

This change corrects the allocation to use one method or the other
and not both.
Signed-off-by: NDaniel Walker <c_dwalke@quicinc.com>

This cleans up coding style. There are no run time changes.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Forcing the alignment prevents gcc from generating byte reads for word
member variables. Lack of this caused issues when the app processor
modified struct members and the modem saw a partial word write.
Signed-off-by: NDima Zavin <dima@android.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Signed-off-by: NDima Zavin <dima@android.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Some smd clients may write from multiple threads, in which case it's
not safe to call smd_write without holding a lock.  smd_write_atomic()
provides the same functionality as smd_write() but obtains the smd
lock first.
Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Signed-off-by: NIliyan Malchev <malchev@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Don't mark a channel as allocated if we failed to allocate it
(perhaps the modem updated one table but not the other, etc)
Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

When we read data out of the sender's fifo, we need to advance the sender's
tail pointer, not the receiver's.
Signed-off-by: NHaley Teng <Haley_Teng@htc.com>
Acked-by: NDima Zavin <dima@android.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

- QSD8250 has a DSP that speaks SMD, in addition to the modem
- handle a separate list of modem vs dsp channels
- install dsp smd irq handler as necessary
Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

- pull debug code into smd_debug.c
- move necessary structures and defines into smd_private.h
- fix some comment formatting, etc
Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Signed-off-by: NArve Hjønnevåg <arve@android.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

The new protocol require writing to two state fields, and reading
several fields.
Signed-off-by: NArve Hjønnevåg <arve@android.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

- support both v2 and v1 style smd channels
- support both v2 and v1 smsm shared state
- update smsm state defines and smem item enum
- prep work for dealing with smd to qdsp6
- simplify some smem access to minimize use of smem_alloc() at runtime
Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This code provides the low level interface to the "shared memory
state machine" (smsm), and the virtual serial channels (smd), used
to communicate with the baseband processor.  Higher level transports
(rpc, ethernet, AT command channel, etc) ride on top of this.
Signed-off-by: NBrian Swetland <swetland@google.com>

Also, convert all SDCC IRQ resources to be named. No longer pass status_irq
in the platform_data
Signed-off-by: NDima Zavin <dima@android.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Signed-off-by: NSan Mehat <san@google.com>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This adds a basic board file without Kconfig changes.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Signed-off-by: NWillie Ruan <wruan@quicinc.com>

Support independent enable and disable by clients for common
vreg. First enable switches on and last disable switches off.

This change has no check for voltage level so clients
must agree on level for common vreg.
Signed-off-by: NMatthew Wilson <mtwilson@quicinc.com>

Fixes the following warning,

arch/arm/mach-msm/acpuclock-arm11.c:138: warning: 'freq_table' defined but not used

when CONFIG_CPU_FREQ_TABLE is not enabled.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Keep track of the success/failure of the last vreg proc comm
command, and return that on debugfs reads.
Signed-off-by: NSteve Muckle <smuckle@quicinc.com>

Signed-off-by: NSteve Muckle <smuckle@quicinc.com>

Move the naming of this board file back to the original Google naming.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This adds acpuclock-arm11.c from Google. This provides control
over the cpu frequency for arm11 cpu's.

This has shared authorship between Google, and Qualcomm. Most
of it was written by Mike Chan at Google.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Avoids problems on the scorpion core.
Signed-off-by: NBrian Swetland <swetland@google.com>

Signed-off-by: NArve Hjønnevåg <arve@android.com>

Signed-off-by: NArve Hjønnevåg <arve@android.com>

Signed-off-by: NDima Zavin <dima@android.com>

Signed-off-by: NBrian Swetland <swetland@google.com>

Signed-off-by: NArve Hjønnevåg <arve@android.com>

This adds a basic board file without Kconfig changes.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This adds a basic board file without Kconfig changes.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This adds a basic board file without Kconfig changes.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This adds a basic board file without Kconfig changes.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

ARCH_MSM supports armv7 cpus, so we're pushed the CPU_V6/CPU_V7 selection
down into the arch/arm/mach-msm/Kconfig.

Also update the description to be a bit more accurate.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

This allows the procfs vmallocinfo file to show who created the ioremap
regions.  Note: __builtin_return_address(0) doesn't do what's expected
if its used in an inline function, so we leave __arm_ioremap callers
in such places alone.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.

NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:

$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
	arch/arm/*/include/*/debug-macro.S
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>