Both HDCP_{1.x,2.x} requires to select/deselect Multistream HDCP bit
in TRANS_DDI_FUNC_CTL in order to enable/disable stream HDCP
encryption over DP MST Transport Link.

HDCP 1.4 stream encryption requires to validate the stream encryption
status in HDCP_STATUS_{TRANSCODER,PORT} register driving that link
in order to enable/disable the stream encryption.

Both of above requirement are same for all Gen with respect to
B.Spec Documentation.

v2:
- Cosmetic changes function name, error msg print and
  stream typo fixes. [Uma]
v3:
- uniformity for connector detail in DMESG. [Ram]

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Tested-by: NKarthik B S <karthik.b.s@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-8-anshuman.gupta@intel.com

DP MST stream encryption status requires time of a link frame
in order to change its status, but as there were some HDCP
encryption timeout observed earlier, it is safer to use
ENCRYPT_STATUS_CHANGE_TIMEOUT_MS timeout for stream status too,
it requires to move the macro to a header.
It will be used by both HDCP{1.x,2.x} stream status timeout.

Related: 'commit 7e90e8d0 ("drm/i915: Increase timeout for Encrypt
status change")'
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Tested-by: NKarthik B S <karthik.b.s@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-7-anshuman.gupta@intel.com

Gen12 has H/W delta with respect to HDCP{1.x,2.x} display engine
instances lies in Transcoder instead of DDI as in Gen11.

This requires hdcp driver to use mst_master_transcoder for link
authentication and stream transcoder for stream encryption
separately.

This will be used for both HDCP 1.4 and HDCP 2.2 over DP MST
on Gen12.

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Tested-by: NKarthik B S <karthik.b.s@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-6-anshuman.gupta@intel.com

There can be situation when DP MST connector is created without
mst modeset being done, in those cases connector->encoder will be
NULL. MST connector->encoder initializes after modeset.
Don't enable HDCP in such cases to prevent any crash.

Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Juston Li <juston.li@intel.com>
Tested-by: NKarthik B S <karthik.b.s@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-5-anshuman.gupta@intel.com

Handle CP_IRQ in DEVICE_SERVICE_IRQ_VECTOR_ESI0
It requires to call intel_hdcp_handle_cp_irq() in case
of CP_IRQ is triggered by a sink in DP-MST topology.

Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Tested-by: NKarthik B S <karthik.b.s@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-4-anshuman.gupta@intel.com

Get DRM connector reference count while scheduling a prop work
to avoid any possible destroy of DRM connector when it is in
DRM_CONNECTOR_REGISTERED state.

Fixes: a6597faa ("drm/i915: Protect workers against disappearing connectors")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Tested-by: NKarthik B S <karthik.b.s@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-3-anshuman.gupta@intel.com

When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.

This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.

v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
  WARN_ON.

v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]

Fixes: 33f9a623 ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Tested-by: NKarthik B S <karthik.b.s@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com

DG1's vswing tables are the same for eDP and HDMI but have slight
differences from ICL/TGL for DP.

v2:
 - Use a "_hbr2_hbr3" suffix on the table name to make it more clear
   that the same table is used for both HBR2 and HBR3 link rates.
   (Swathi)

Bspec: 49291
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108222528.1954514-1-matthew.d.roper@intel.comReviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>

Some new eDP panels don't like to operate at the max parameters, and
instead we need to go for an optimal confiugration. That unfortunately
doesn't work with older eDP panels which are generally only guaranteed
to work at the max parameters.

To solve these two conflicting requirements let's start with the optimal
setup, and if that fails we start again with the max parameters. The
downside is probably an extra modeset when we switch strategies but
I don't see a good way to avoid that.

For a bit of history we first tried to go for the fast+narrow in
commit 7769db58 ("drm/i915/dp: optimize eDP 1.4+ link config
fast and narrow"). but that had to be reverted due to regression
on older panels in commit f11cb1c1 ("drm/i915/dp: revert back
to max link rate and lane count on eDP"). So now we try to get
the best of both worlds by using both strategies.

v2: Deal with output_bpp and uapi vs. hw state split
    Reword some comments
v3: Rebase

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Albert Astals Cid <aacid@kde.org> # v5.0 backport
Cc: Emanuele Panigati <ilpanich@gmail.com> # v5.0 backport
Cc: Matteo Iervasi <matteoiervasi@gmail.com> # v5.0 backport
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=105267
References: https://bugs.freedesktop.org/show_bug.cgi?id=109959
References: https://gitlab.freedesktop.org/drm/intel/issues/272Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107182026.24848-1-ville.syrjala@linux.intel.com

Eliminate checkpatch warnings from intel_cursor.c:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Possible repeated word: 'by'
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110175624.3524-2-ville.syrjala@linux.intel.comReviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>

There was some misinterpretation of specification, when DDIX_USED is
set, the next bit means 0 for DP and 1 for HDMI.

Anyways this misinterpretation is not causing any issues, this change
is just to comply with specification.
Also as for us it do not matters if it is HDMI or DP, not checking the
port type that HTI is using.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108134802.21280-1-jose.souza@intel.com

The pch_get_backlight(), lpt_get_backlight(), and lpt_set_backlight()
functions operate directly on the hardware registers. If inverting the
value is needed, using intel_panel_compute_brightness(), it should only
be done in the interface between hardware registers and
panel->backlight.level.

The CPU mode takeover code added in commit 5b1ec9ac
("drm/i915/backlight: Fix backlight takeover on LPT, v3.") reads the
hardware register and converts to panel->backlight.level correctly,
however the value written back should remain in the hardware register
"domain".

This hasn't been an issue, because GM45 machines are the only known
users of i915.invert_brightness and the brightness invert quirk, and
without one of them no conversion is made. It's likely nobody's ever hit
the problem.

Fixes: 5b1ec9ac ("drm/i915/backlight: Fix backlight takeover on LPT, v3.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108152841.6944-1-jani.nikula@intel.com

We need a power_domain wakeref in pps_{lock,unlock} to prevent
a race while resetting pps state in intel_power_sequencer_reset().

intel_power_sequencer_reset() need a pps_mutex to access pps_pipe
but it can't grab pps_mutex due to deadlock with power_well
functions are called while holding pps_mutex.
intel_power_sequencer_reset() is called by power_well function
associated with legacy platforms like vlv and chv therefore re-use
the POWER_DOMAIN_DISPLAY_CORE power domain, which only used
by vlv and chv display power domain.

This will avoids the unnecessary noise of unrelated power wells
in pps_{lock,unlock}.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210107112500.16216-1-anshuman.gupta@intel.com

drm/i915/dsi: Use unconditional msleep for the panel_on_delay when there is no reset-deassert MIPI-sequence

Commit 25b4620e ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
added an intel_dsi_msleep() helper which skips sleeping if the
MIPI-sequences have a version of 3 or newer and the panel is in vid-mode;
and it moved a bunch of msleep-s over to this new helper.

This was based on my reading of the big comment around line 730 which
starts with "Panel enable/disable sequences from the VBT spec.",
where the "v3 video mode seq" column does not have any wait t# entries.

Given that this code has been used on a lot of different devices without
issues until now, it seems that my interpretation of the spec here is
mostly correct.

But now I have encountered one device, an Acer Aspire Switch 10 E
SW3-016, where the panel will not light up unless we do actually honor the
panel_on_delay after exexuting the MIPI_SEQ_PANEL_ON sequence.

What seems to set this model apart is that it is lacking a
MIPI_SEQ_DEASSERT_RESET sequence, which is where the power-on
delay usually happens.

Fix the panel not lighting up on this model by using an unconditional
msleep(panel_on_delay) instead of intel_dsi_msleep() when there is
no MIPI_SEQ_DEASSERT_RESET sequence.

Fixes: 25b4620e ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118124058.26021-1-hdegoede@redhat.com

The bspec has been updated with new vswing programming for RKL DP.  No
data is provided for HDMI or eDP, so for now we'll continue to assume
that those are the same as TGL.

Bspec: 49291
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218040535.45492-1-matthew.d.roper@intel.comReviewed-by: NSwathi Dhanavanthri <swathi.dhanavanthri@intel.com>

After boot into kernel. Driver configured ddc pin mapping based on
predefined table in parse_ddi_port(). Now driver configure rkl
ddc pin mapping depends on icp_ddc_pin_map[]. Then this table will
give incorrect gmbus port number to cause HDMI can't work.

Refer to commit cd0a8952 ("drm/i915/rkl: Add DDC pin mapping").
Create two ddc pin table for rkl TGP and CMP pch. Then HDMI can
works properly on rkl.

v2: update patch based on latest dinq branch.
v3: update ddc table for RKL+TGP sku.
    RKL+CNP sku will load cnp_ddc_pin_map[] setting.
v4: modify the if/else judgment to avoid nesting.
v5: fix typo in v4.

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2577Signed-off-by: NLee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117142629.28729-1-shawn.c.lee@intel.com

It programs Plane's calculated x, y, offset to Plane SF register.
It does the calculation of x and y offsets using
skl_calc_main_surface_offset().

v3: Update commit message

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-4-jose.souza@intel.com

The calculation the offsets of the main surface will be needed by PSR2
selective fetch code so here splitting and exporting it.
No functional changes were done here.

v3: Rebased

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-3-jose.souza@intel.com

Now using plane damage clips property to calcualte the damaged area.
Selective fetch only supports one region to be fetched so software
needs to calculate a bounding box around all damage clips.

Now that we are not complete fetching each plane, there is another
loop needed as all the plane areas that intersect with the pipe
damaged area needs to be fetched from memory so the complete blending
of all planes can happen.

v2:
- do not shifting new_plane_state->uapi.dst only src is in 16.16 format

v4:
- setting plane selective fetch area using the whole pipe damage area
- mark the whole plane area damaged if plane visibility or alpha
changed

v5:
- taking in consideration src.y1 in the damage coordinates
- adding to the pipe damaged area planes that were visible but are
invisible in the new state

v6:
- consider old state plane coordinates when visibility changes or it
moved to calculate damaged area
- remove from damaged area the portion not in src clip

v7:
- intersec every damage clip with src to minimize damaged area

v8:
- adjust pipe_damaged area to 4 lines grouping
- adjust calculation now that is understood that uapi.src is the
framebuffer coordinates that plane will start to fetch from

v9:
- Only add plane dst or src to damaged_area if visible
- Early skip plane damage calculation if it was not visible in old and
new state

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-2-jose.souza@intel.com

Since multiple connectors may run intel_dp_aux_xfer conncurrently, a
single global pm_qos does not suffice. (One connector may disable the
dma-latency boost prematurely while the second is still depending on
it.) Instead of a single global pm_qos, track the pm_qos request for
each intel_dp.

v2: Move the pm_qos setup/teardown to intel_dp_aux_init/fini

Fixes: 9ee32fea ("drm/i915: irq-drive the dp aux communication")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201230202309.23982-1-chris@chris-wilson.co.uk

No functional changes yet, this just adds definitions for all of the
known DPCD registers used by Intel's HDR backlight interface. Since
we'll only ever use this in i915, we just define them in
intel_dp_aux_backlight.c
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-7-lyude@redhat.com

Since we're about to add support for a second type of backlight control
interface over DP AUX (specifically, Intel's proprietary HDR backlight
controls) let's rename all of the current backlight hooks we have for
vesa to make it clear that they're specific to the VESA interface and
not Intel's.

v3:
* Rebase
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-6-lyude@redhat.com

Instead of using intel_panel->backlight.level, have the caller provide us
with the current panel backlight value. We'll need this for when we
separate PWM-related backlight callbacks from other means of backlight
control (like DPCD backlight controls), as the caller of each PWM callback
will be responsible for converting the current brightness value to it's
respective PWM level.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-4-lyude@redhat.com

Since we're going to need to add a set of lower-level PWM backlight
control hooks to be shared by normal backlight controls and HDR
backlight controls in SDR mode, let's add a prefix to the external PWM
backlight functions so that the difference between them and the high
level PWM-only backlight functions is a bit more obvious.

This introduces no functional changes.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-3-lyude@redhat.com

Since we're about to start adding support for Intel's magic HDR
backlight interface over DPCD, we need to ensure we're properly
programming this field so that Intel specific sink services are exposed.
Otherwise, 0x300-0x3ff will just read zeroes.

We also take care not to reprogram the source OUI if it already matches
what we expect. This is just to be careful so that we don't accidentally
take the panel out of any backlight control modes we found it in.

v2:
* Add careful parameter to intel_edp_init_source_oui() to avoid
  re-writing the source OUI if it's already been set during driver
  initialization
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-2-lyude@redhat.com

If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.

v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.

v3: Fixed typo in condition for printing one of the error msg.

v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-16-ankit.k.nautiyal@intel.com

When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.

This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.

v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message

v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com

The DP-HDMI2.1 PCON spec provides way for a source to set PPS
parameters: slice height, slice width and bits_per_pixel, based on
the HDMI2.1 sink capabilities. The DSC encoder of the PCON will
respect these parameters, while preparing the 128 byte PPS.

This patch adds helper functions to calculate these PPS paremeters as
per the HDMI2.1 specification.

v2: Addressed review comments given by Uma Shankar:
-added documentation for functions
-fixed typos and errors
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch SUSPECT_CODE_INDENT, TYPO_SPELLING]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-14-ankit.k.nautiyal@intel.com

This patch adds support to read and store the DSC capabilities of the
HDMI2.1 PCon encoder. It also adds a new field to store these caps,
The caps are read during dfp update and can later be used to get the
PPS parameters for PCON-HDMI2.1 sink pair. Which inturn will be used
to take a call to override the existing PPS-metadata, by either
writing the entire new PPS metadata, or by writing only the
PPS override parameters.

v2: Restructured the code to read all capability DPCDs at once and store
in an array in intel_dp structure.

v3: rebase
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-13-ankit.k.nautiyal@intel.com

In this patch enables support for detecting link failures between
PCON and HDMI sink in i915 driver. HDMI link loss indication to
upstream DP source is indicated via IRQ_HPD. This is followed by
reading of HDMI link configuration status (HDMI_TX_LINK_ACTIVE_STATUS).
If the PCON → HDMI 2.1 link status is off; reinitiate frl link
training to recover. Also, report HDMI FRL link error count range for
each individual FRL active lane is indicated by
DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.

v2: Checked for dpcd read and write failures and added debug message.
(Uma Shankar)

v3: Rearranged code to re-start FRL link training or fall back to
TMDS mode.

v4: Resused function to check frl which inturn restarts FRL and
fallback to TMDS mode.
Signed-off-by: NSwati Sharma <swati2.sharma@intel.com>
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-12-ankit.k.nautiyal@intel.com

This patch calls functions to check FRL training requirements
for an HDMI2.1 sink, when connected through PCON.
The call is made before the DP link training. In case FRL is not
required or failure during FRL training, the TMDS mode is selected
for the pcon.

v2: moved check_frl_training() just after FEC READY, before
starting DP link training.

v3: rebase
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-11-ankit.k.nautiyal@intel.com

This patch adds functions to start FRL training for an HDMI2.1 sink,
connected via a PCON as a DP branch device.
This patch also adds a new structure for storing frl training related
data, when FRL training is completed.

v2: As suggested by Uma Shankar:
-renamed couple of variables for better clarity
-tweaked the macros used for correct semantics for true/false
-fixed other styling issues.

v3: Completed the TODO for condition for going to FRL mode.
Modified the condition to determine the required FRL b/w
based only on the Pcon and Sink's max FRL values.
Moved the frl structure initialization to intel_dp_init_connector().

v4: Fixed typo in initialization of frl structure.

v5: Always use FRL if its possible, instead of enabling only for
higher modes as done in v3.
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
[Jani: Fixed checkpatch BRACES, CONSTANT_COMPARISON.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-10-ankit.k.nautiyal@intel.com

HDMI2.1 PCON advertises Max FRL bandwidth supported by the PCON.

This patch captures this in dfp cap structure in intel_dp and uses
this to prune connector modes that cannot be supported by the PCON
and FRL bandwidth.

v2: Addressed review comments from Uma Shankar:
-tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
-minor modification of field names and comments.
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-9-ankit.k.nautiyal@intel.com

Ville suggested this as a good idea, let's move this before moving
the crtc code.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed i915xx_plane.h standalone build.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201221110957.18215-1-jani.nikula@intel.com

This file is a monster, let's start simple, the cursor plane code
seems pretty standalone, and splits out easily enough.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
[Jani: cleaned up intel_cursor.h a bit.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201221090449.8288-4-jani.nikula@intel.com

There is no need for a comma use here.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201221090449.8288-3-jani.nikula@intel.com

This will be used for some refactoring in other files, so move it
first.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201221090449.8288-2-jani.nikula@intel.com

This function is going to be used in a later change, so clean it
up first before moving it.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201221090449.8288-1-jani.nikula@intel.com

Nothing uses the result and nothing should ever use it in driver code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20201210194043.862572239@linutronix.de

To support legacy gamma ioctls the drivers need to set
drm_crtc_funcs.gamma_set either to a custom implementation or to
drm_atomic_helper_legacy_gamma_set. Most of the atomic drivers do the
latter.

We can simplify this by making the core handle it automatically.

Move the drm_atomic_helper_legacy_gamma_set() functionality into
drm_color_mgmt.c to make drm_mode_gamma_set_ioctl() use
drm_crtc_funcs.gamma_set if set or GAMMA_LUT property if not.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NPhilippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201211114237.213288-2-tomi.valkeinen@ti.com