Use the ftrace infrastructure to conditionally trace ufs command events.
New trace event is created, which samples the following ufs command data:
- device name
- optional identification string
- task tag
- doorbell register
- number of transfer bytes
- interrupt status register
- request start LBA
- command opcode

Currently we only fully trace read(10) and write(10) commands.
All other commands which pass through ufshcd_send_command() will be
printed with "-1" in the lba and transfer_len fields.

Usage:
	echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
	cat /sys/kernel/debug/tracing/trace_pipe
Signed-off-by: NLee Susman <lsusman@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds the profiling support for some of the time critical
operations like hibern8 enter/exit, clock gating & clock scaling.
Reviewed-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Immediately after successful UFS link startup, UFS link power mode would
be in PWM-G1, 1-lane, SLOW-AUTO mode. But currently we are doing few
of the DME local/peer attributes access before setting the "hba->pwr_info"
to default power mode. If we are doing link startup as part of error
recovery then old power mode might be set to FAST mode and doing DME peer
access (after link startup but before updating "hba->pwr_info" to default
power mode) unintentionally tries to switch from FAST to FAST_AUTO mode (if
UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE quirk is enabled).

Above issue is fixed by setting the default power mode immediately after
successful link startup.
Reviewed-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

UFS device requires to perform bkops (back ground operations) periodically
but host can control (via auto-bkops parameter of device) when device can
perform bkops based on its performance requirements. In general, host
would like to enable the device's auto-bkops only when it's not doing any
regular data transfer but sometimes device may not behave properly if host
keeps the auto-bkops disabled. This change adds the capability to let the
device auto-bkops always enabled except suspend.
Reviewed-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

UFS device and link can be put in multiple different low power modes hence
UFS driver supports multiple different low power modes.
This change sets the default UFS power management level which should put
the link hibernate state and device in sleep state. This default power
management level gives good  power savings with relatively less enter/exit
latencies.
Reviewed-by: NYaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch provides the sysfs attribute to choose the power management
level for UFS runtime and system suspend.
Reviewed-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Provide an option to enable/disable clock scaling during runtime.
Write 1/0 to "clkscale_enable" sysfs node to enable/disable clock
scaling.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Provide an option to enable/disable clock gating during runtime.
Write 1 or 0 to "clkgate_enable" sysfs node to enable/disable
clock gating.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When a command to a W-LU is timed out via scsi, error handling
will treat it as any other LU and send commands such as
START_STOP with wrong format or task abort. Those commands are
illegal for W-LU according to the UFS spec.
To solve it, when an error is recognized those steps are skipped
and the last step, reset and restore process, is initiated.
Signed-off-by: NDolev Raviv <draviv@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This change adds the ftrace support for following:
1. UFS initialization time
2. Clock gating states
3. Clock scaling states
4. Power management APIs latency
5. BKOPs enable/disable

Usage:
	echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
	cat /sys/kernel/debug/tracing/trace_pipe
Reviewed-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Inserts driver dumps for UFS Host Controller registers, Transfer Requests
and Task Management Requests.
The dumps will occur on driver initialization failure, ufshcd_abort() and
on error handling path.
Signed-off-by: NDolev Raviv <draviv@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NCao jin <caoj.fnst@cn.fujitsu.com>
Acked-by: NNilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Although on most systems va_end is a no-op, it is good practice to use
va_end on the function return path, especially since the va_start
documenation states:

  "Each invocation of va_start() must be matched by a corresponding
   invocation of va_end() in the same function."

Found with static analysis by CoverityScan, CIDs 1389477-1389479
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NManish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Version 11.2.1.0
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add a warning message to indicate obsolete/unsupported
BE2 Adapter Family devices
Signed-off-by: NKetan Mukadam <ketan.mukadam@avagotech.com>
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After TPE recovery, CID table needs to be repopulated as per CIDs in
WRBQ creation responses.

SGL handles table needs to be recreated for posting and its indices need
to be resetted.

This is achieved by calling beiscsi_cleanup_port when disabling and
beiscsi_init_port in enabling port.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Set CID slot to 0xffff to indicate empty.
Check if connection already exists in conn_table before binding.
Check if endpoint already NULL before putting back CID.
Break ep->conn link in free_ep to ignore completions after freeing.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

wq_name is used only to set WQ name when its being allocated.
Remove it from beiscsi_hba structure and define locally.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix errors reported in static analysis.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This duplicate code got added during manual merging.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Prepare the IOCTL with appropriate sizes of buffers of V0 and V1.
Set missing chute number in V1 IOCTL.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added check in beiscsi_process_cq for pio_handle.
pio_handle is cleared in beiscsi_put_wrb_handle.
This catches any case where task gets cleaned up just before completion.

Use back_lock before accessing pio_handle.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

invalid bit in WRB indicates to FW that IO was invalidated before WRB
was fetched from host memory.

For SkyHawk, this invalid bit in WRB is at a different offset.
Use amap_iscsi_wrb_v2 to mark invalid bit for SkyHawk.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Hold the reference of iscsi_task till invalidation completes.
This prevents use of ICD when invalidation of that ICD is being processed.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

System crashes when sg_reset is executed in a loop.
CPU: 13 PID: 7073 Comm: sg_reset Tainted: G            E   4.8.0-rc1+ #4
RIP: 0010:[<ffffffffa0825370>]  [<ffffffffa0825370>]
beiscsi_eh_device_reset+0x160/0x520 [be2iscsi]
Call Trace:
[<ffffffff814c7c77>] ? scsi_host_alloc_command+0x47/0xc0
[<ffffffff814caafa>] scsi_try_bus_device_reset+0x2a/0x50
[<ffffffff814cb46e>] scsi_ioctl_reset+0x13e/0x260
[<ffffffff814ca477>] scsi_ioctl+0x137/0x3d0
[<ffffffffa05e4ba2>] sg_ioctl+0x572/0xc20 [sg]
[<ffffffff8123f627>] do_vfs_ioctl+0xa7/0x5d0

The accesses to beiscsi_io_task is being protected in device reset handler
with frwd_lock but the freeing of task can happen under back_lock.

Hold the reference of iscsi_task till invalidation completes.
This prevents use of ICD when invalidation of that ICD is being processed.
Use frwd_lock for iscsi_tasks looping and back_lock to access
beiscsi_io_task structures.

Rewrite mgmt_invalidation_icds to handle allocation and freeing of IOCTL
buffer in one place.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove shared structure inv_tbl in phba for all sessions to post
invalidation IOCTL.
Always allocate and then free the table after use in reset handler.
Abort handler needs just one instance so define it on stack.
Add checks for BE_INVLDT_CMD_TBL_SZ to not exceed invalidation
command table size in IOCTL.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are two places where adpt_i2o_online_hba() is called.  Both
callers call adpt_i2o_delete_hba(pHba) if adpt_i2o_online_hba() fails
and since we also free it here that causes a double free bug.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch remove linux/miscdevice.h from mptlan.h since mptlan.h does
not contain any miscdevice.  The only user of it is mptctl.c which
already include linux/miscdevice.h So no need to include it twice.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

lpfc version change to 11.2.0.4
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On loosely ordered memory systems (PPC for example), the WQE elements
were being updated in memory, but not necessarily flushed before the
separate doorbell was written to hw which would cause hw to dma the
WQE element. Thus, the hardware occasionally received partially
updated WQE data.

Add the memory barrier after updating the WQE memory.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Correct oops on vport port resets. Incorrect WQE type, thus the clearing
code actually overstepped the WQE.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Deprecate lpfc_prot_sg_seg_cnt parameter. Eliminates driver from
unnecessarily limiting DIF s/g list length.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix Xlane dynamic LUN set for LUN priority. Dynamic changing of the
priority was not getting reflected on the LUN.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

FCoE VPort enable-disable does not bring up the VPort.
VPI structure needed to be initialized before being re-registered.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Correct host name in symbolic_name field of nameserver registrations
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Correct issue leading to oops during link reset. Missing vport pointer.

[mkp: fixed typo]
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Deprecate lpfc_soft_wwn parameter.
No longer allow override of hw-assigned wwns
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Correct error in setting OS Driver Version with FW.  Prior length was
too short.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@Suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>